hathach
752aea7d72
enhance samg
2019-12-09 23:58:13 +07:00
hathach
fa96078882
clear data toggle in clear stall, also set config bit
2019-12-09 23:21:06 +07:00
hathach
75a2157715
fix samd using TUSB_REQ_SET_ADDRESS in dcd_edpt0_status_complete
2019-12-09 23:20:21 +07:00
hathach
0316e0ecd4
update descriptor, enhance ep in transfer
2019-12-09 22:48:35 +07:00
hathach
759fa76280
implementing dcd_edpt_open
2019-12-09 21:36:15 +07:00
hathach
988edce745
fix build
2019-12-09 18:49:38 +07:00
hathach
208a77678c
clean up, switch and update submodule samd to circuitpython branch
2019-12-09 18:37:54 +07:00
Sean Cross
26dcc19b18
valentyusb: eptri: don't double-advance read buffer
...
Due to an error, we were double-advancing the FIFO buffer. The end
result was that the second half of most reads were getting ignored.
This wasn't found during earlier testing because only 64-byte buffers
were tested.
This corrects this error by avoiding double-advancing the buffer.
Signed-off-by: Sean Cross <sean@xobs.io>
2019-11-29 18:14:23 +08:00
hathach
e9725dcdbe
use dcd_edpt0_status_complete() to prepare for setup packet for samd21/samd51
2019-11-28 13:48:55 +07:00
hathach
d7558e8a0f
use dcd_edpt0_status_complete() to set address without blocking for samd21/samd51/stm32_fsdev
2019-11-28 13:39:29 +07:00
hathach
ac701c398b
clean up
2019-11-28 12:18:56 +07:00
hathach
552cc3ef33
implement dcd_edpt_stall
2019-11-28 11:56:35 +07:00
hathach
5dc04887e2
get passed set address
2019-11-28 11:48:08 +07:00
hathach
6bc245cb36
add dcd_edpt0_status_complete() which is useful for several mcu port
2019-11-28 11:46:36 +07:00
hathach
40b454cf28
get passed first get device descriptor
2019-11-27 23:20:48 +07:00
hathach
6225d5bcfd
able to handle setup packet
2019-11-27 16:01:25 +07:00
hathach
bc21714c7e
detect bus reset
2019-11-27 14:49:19 +07:00
hathach
745f0b4521
clean up
2019-11-27 11:02:24 +07:00
hathach
c691dc4cb2
update
2019-11-25 10:42:32 +07:00
hathach
58e8265964
usb hw init OK
2019-11-24 23:46:28 +07:00
hathach
24b2cea139
Merge branch 'master' into port-samg55
2019-11-24 21:22:42 +07:00
hathach
d991466a8e
fix rt1010 rt1020 only has 1 usb controller, rt1050 rt1060 has 2
2019-11-23 00:48:56 +07:00
hathach
38b14725f7
rename OPT_MCU_IMXRT10XX to OPT_MCU_MIMXRT10XX
2019-11-22 17:40:12 +07:00
hathach
281e8cd9ec
rename OPT_MCU_RT10XX to OPT_MCU_IMXRT10XX
2019-11-22 15:42:46 +07:00
Ha Thach
ca741dfc2a
Merge pull request #220 from hathach/develop
...
Port NXP iMX RT10XX
2019-11-22 15:16:41 +07:00
hathach
6123b600fc
rename dcd_lpc18_43 to dcd_transdimension
2019-11-22 14:47:07 +07:00
hathach
a0b2561a2d
move nxp dcd ehci controller reset and modde into dcd
...
rt1064 work with cdc msc example
2019-11-22 14:20:10 +07:00
hathach
fca4653b95
able to compile dcd 18/43 with rt1064
2019-11-22 12:34:41 +07:00
hathach
2ead26a12d
more clean up
2019-11-22 12:26:40 +07:00
hathach
ccb09db3b7
more clean up
2019-11-22 12:16:47 +07:00
hathach
7e16a9a1db
more constant rename clean up
2019-11-22 12:14:55 +07:00
hathach
8aacd1eacd
refactor dcd_lpc18_43, making it capatible with rt10xx
2019-11-22 12:11:13 +07:00
hathach
623b16af2e
clean up dcd lpc18_43
...
drop supporting both device mode on both ports.
2019-11-22 00:58:18 +07:00
hathach
1f52273d99
move dcd_lpc18_43.h into .c file
2019-11-22 00:38:22 +07:00
hathach
f5d737aa7e
moving irq to bsp for lpc17/40
2019-11-21 23:19:38 +07:00
hathach
043697ab95
rename lpc 17/18 irq to dcd_isr/hcd_isr
2019-11-21 16:08:08 +07:00
Sean Cross
a9282eab51
eptri: clear proper endpoint when opening IN port
...
When opening a USB port, we ensure the buffer is NULL and has
a length of 0.
Due to a mistake in specifying the endpoint type, we never actually
cleared the value when opening an IN endpoint. This patch fixes
the comparison when opening an IN endpoint.
This fixes issue #218 .
Signed-off-by: Sean Cross <sean@xobs.io>
2019-11-20 17:45:21 +08:00
Sean Cross
8c5f02960b
valentyusb: rename from `foosn`
...
While Fomu is produced by Foosn, the actual name of the hardware
block is `valentyusb`. Rename the module to match that.
Signed-off-by: Sean Cross <sean@xobs.io>
2019-11-13 09:08:47 -08:00
Sean Cross
e05e9801e4
fomu: gate debug/logging features
...
This gates the majority of the debug and logging features behind
testable macros.
Signed-off-by: Sean Cross <sean@xobs.io>
2019-11-13 09:08:47 -08:00
Sean Cross
3292920933
fomu: first stable working commit
...
This appears to be stable, and works well.
Signed-off-by: Sean Cross <sean@xobs.io>
2019-11-13 09:08:47 -08:00
Sean Cross
1882a87212
fomu: remove reference to SETUP_CTRL.ACK
...
THis bit isn't used anymore, so remove it.
Signed-off-by: Sean Cross <sean@xobs.io>
2019-11-13 09:08:47 -08:00
Sean Cross
729c8d073c
fomu: dcd_fomu: add next_ev support
...
Now that we have the `USB_NEXT_EV` register, take advantage of
it to work around issue #207 .
Signed-off-by: Sean Cross <sean@xobs.io>
2019-11-13 09:09:38 -08:00
Sean Cross
913032ae1d
dcd_fomu: nearly there
...
Signed-off-by: Sean Cross <sean@xobs.io>
2019-11-13 09:08:01 -08:00
Sean Cross
835a72c595
fomu: semi-working dcd file
...
Signed-off-by: Sean Cross <sean@xobs.io>
2019-11-13 09:08:01 -08:00
Sean Cross
843136d0e4
fomu: commit latest version
...
Signed-off-by: Sean Cross <sean@xobs.io>
2019-11-13 09:08:01 -08:00
Sean Cross
22fd7bf85e
fomu: first fully-working release
...
This is able to transfer lots of data back and forth across MSC.
Signed-off-by: Sean Cross <sean@xobs.io>
2019-11-13 09:08:01 -08:00
Sean Cross
0559fd13fb
fomu: fix some issues with dcd_fomu
...
Signed-off-by: Sean Cross <sean@xobs.io>
2019-11-13 09:08:01 -08:00
Sean Cross
32bb68409e
portable: fomu: get msc to enumerate
...
Signed-off-by: Sean Cross <sean@xobs.io>
2019-11-13 09:03:12 -08:00
Sean Cross
36ede44885
fomu: wip support
...
Signed-off-by: Sean Cross <sean@xobs.io>
2019-11-13 09:03:12 -08:00
hathach
4008f0d1e6
update dcd nrf5x to be indepent from nrf_usbd.h
...
fix build error with nrfx 2.0
2019-11-11 00:01:12 +07:00
hathach
6baa79b330
board test works
2019-11-04 14:54:04 +07:00
William D. Jones
5d585c03bd
dcd_msp430x5xx: Improve comments regarding SETUP packet handling.
2019-10-29 14:08:39 -04:00
William D. Jones
3f0f7cfd07
dcd_msp430x5xx: Clarify hardware STALL behavior and current vs ideal
...
behavior of driver in comments.
2019-10-29 12:52:56 -04:00
hathach
4e8c57171c
Merge branch 'master' into cr1901-msp430f5529
2019-10-25 21:20:05 +07:00
William D. Jones
d0146be00b
dcd_msp430x5xx: Fix typo in copy-paste in transmit_packet.
2019-10-10 04:19:48 -04:00
William D. Jones
c8e899fef0
dcd_msp430x5xx: Improve SETUP packet and EP0 NAK interactions, per
...
42.3.1.3 in Reference Manual; fix is incomplete but works.
2019-10-10 04:02:35 -04:00
hathach
c42edc080c
Merge branch 'master' into develop
2019-10-09 11:03:55 +07:00
Kamil Tomaszewski
0cea82568c
Disable/enable only USB interrupt
2019-10-08 09:58:56 +02:00
Kamil Tomaszewski
9923604221
Send SUSPEND and RESUME signals
2019-10-07 14:04:48 +02:00
Kamil Tomaszewski
b3872febe2
Disable/enable interrupt
2019-10-07 14:03:02 +02:00
Kamil Tomaszewski
0747c4b61b
Add Spresense board
2019-10-04 13:19:34 +02:00
hathach
281cd858b0
adding lpc1549, but couldnt recieve setup packet, though setup received interrupt is triggered
2019-10-04 15:56:45 +07:00
William D. Jones
5ee1070c16
Merge remote-tracking branch 'origin' into msp430f5529
2019-10-02 23:18:49 -04:00
William D. Jones
05914de109
dcd_msp430x5xx: Fix typos in dcd_edpt_clear_stall.
2019-10-02 22:36:45 -04:00
William D. Jones
3edb5548e9
dcd_msp430x5xx: Ensure DBUF bit is cleared on endpoint open, as it
...
could get spuriously set in debugging sessions. cdc_msc functional.
2019-10-02 01:19:12 -04:00
hathach
820a3705f5
Merge branch 'master' into develop
2019-10-02 12:13:47 +07:00
hathach
0673be7724
ported stm32f1, tested with f103 blue pill
2019-10-02 12:01:34 +07:00
Nathan Conrad
1e193212d7
Add testcase for EP0 stall recovery to USBTMC test script.
2019-10-02 00:31:47 -04:00
Nathan Conrad
e5f38e3e86
Remove references to EP kind.
2019-10-02 00:11:16 -04:00
Nathan Conrad
838cfe02c1
Merge remote-tracking branch 'origin/master' into ST_FSDEV_EP0
2019-10-02 00:09:07 -04:00
William D. Jones
19ee519926
dcd_msp430x5xx: Correct byte count masks in transmit/receive routines.
2019-10-02 00:01:58 -04:00
William D. Jones
54478aaa2a
dcd_msp430x5xx: Add STALL support for nonzero endpoints.
2019-10-01 23:28:41 -04:00
William D. Jones
fad44c03c8
dcd_msp430x5xx: Fix TOGGLE bit behavior, clear stall when endpoint
...
opened due to reset potentially not resetting everything.
2019-10-01 23:03:39 -04:00
hathach
d27291f288
Merge branch 'master' into develop
2019-09-30 14:45:34 +07:00
William D. Jones
b623e3023e
dcd_msp430x5xx: Implement receive_packet for all endpoints, correct
...
some mistakes in transmit_packet.
2019-09-29 03:58:30 -04:00
William D. Jones
549ad1d9b6
dcd_msp430x5xx: Fix missing mask when posting IN xfer events.
2019-09-29 03:02:59 -04:00
William D. Jones
838b431fac
dcd_msp430x5xx: Implement transmit_packet for nonzero endpoints. Untested.
2019-09-29 02:43:05 -04:00
William D. Jones
2247f132ca
Implement dcd_edpt_xfer for nonzero endpoints.
2019-09-29 02:22:09 -04:00
William D. Jones
ea0e799df6
dcd_msp430x5xx: Fix clear stall logic.
2019-09-29 02:17:59 -04:00
William D. Jones
529efcc0d2
dcd_msp430x5xx: Implement dcd_edpt_open.
2019-09-29 00:21:40 -04:00
William D. Jones
5d9f833915
dcd_msp430x5xx: Implement STALL logic for EP 0.
2019-09-28 02:09:03 -04:00
William D. Jones
63c94ff684
dcd_msp430x5xx: Improve EP0 IN handling (reuse short_packet field).
2019-09-28 01:51:05 -04:00
William D. Jones
030560792d
dcd_msp430x5xx: Implement dcd_set_address.
2019-09-27 21:59:45 -04:00
William D. Jones
3ac43076da
dcd_msp430x5xx: Implement EP0 IN xfers, clean up.
2019-09-27 21:22:19 -04:00
Nathan Conrad
c4483d244b
Fix typo of CFG_TUD_ENDOINT0_SIZE.
2019-09-27 21:22:19 -04:00
Nathan Conrad
4ccdc5522d
Fix typo of CFG_TUD_ENDOINT0_SIZE.
2019-09-27 12:41:46 -04:00
hathach
6183dbd0ce
add -Wextra for more warnings to example
...
non-stack warning (probably mcu driver) should be suppressed in the
board.mk
2019-09-27 00:15:43 +07:00
Nathan Conrad
f19082f02d
Reset TX and RX endpoints to NAK when receiving setup packet.
2019-09-25 20:55:15 -04:00
Nathan Conrad
048e0448c0
ST FSDEV:Remove setting the EP kind, as I think it was causing issues during enumeration (sometimes). Also move a membar.
2019-09-25 20:54:59 -04:00
William D. Jones
01b4115b0b
dcd_msp430x5xx: Fix Setup packet delay by actually enabling
...
corresponding interrupt.
2019-09-24 04:06:34 -04:00
William D. Jones
550e8215f3
dcd_msp430x5xx: Setup packets are now received successfully (with delay).
2019-09-24 03:43:51 -04:00
William D. Jones
d2e4af5a7b
msp430f5529: Change EP0 size to 8, implement interrupt logic up to bus
...
reset detection.
2019-09-24 02:41:11 -04:00
William D. Jones
950614a841
msp430f5529: Implement dcd_int_enable/disable.
2019-09-23 22:58:49 -04:00
William D. Jones
a6a79df9fb
msp430f5529: Enable clocks/PLL for msp_exp430f5529lp and enable USB
...
module in dcd_msp430x5xx; device does not enumerate.
2019-09-23 18:53:31 -04:00
William D. Jones
907bc3df9b
msp430f5529: Ensure cdc_msc demo compiles.
2019-09-23 17:48:18 -04:00
hathach
7ba8e81852
Merge pull request #177 from cr1901/fifo-fix
...
dcd_synopsys: Fix off-by-one error in FIFO allocation.
2019-09-22 11:38:54 +07:00
William D. Jones
108f756e22
dcd_synopsys: Fix off-by-one error in FIFO allocation.
2019-09-21 23:01:06 -04:00
Nathan Conrad
ce9f133d25
FSDEV: go to NAK when unstalling; on reset, set EP0 to NAK, prioritize reset interrupt, fix small typos.
2019-09-21 12:00:04 -04:00
hathach
94c9cf0eff
doc update
2019-09-20 16:14:35 +07:00
hathach
7b2f8cc73a
added stm32 L0 support
...
close #125
2019-09-20 13:49:33 +07:00
Nathan Conrad
525b4cdb72
Use ESOF for wakeup timing.
2019-09-19 09:51:40 -04:00
Nathan Conrad
642afeea8b
s/static const/define/
2019-09-19 09:30:16 -04:00
Nathan Conrad
85623584f9
Remove debug assertions.
2019-09-19 09:24:52 -04:00
Nathan Conrad
5fcc1468eb
Merge branch 'master' into fsdev_smallPacket
2019-09-19 09:16:48 -04:00
Nathan Conrad
89ffe78f84
ST FSDEV: No need to always reset the interrupt priority, also add some synchronization primitives after disabling interrupts.
2019-09-16 22:56:17 -04:00
Nathan Conrad
a33a854793
Include board header file... :X
2019-09-16 20:56:57 -04:00
Nathan Conrad
d341337c6a
Implement remote wakeup + perhaps better sleep?
2019-09-16 20:25:50 -04:00
Nathan Conrad
6b9783cead
s/unsigned int/uint32_t/
2019-09-16 09:20:15 -04:00
hathach
0c70948d0d
Merge pull request #163 from hathach/develop
...
fix #143
2019-09-16 16:37:27 +07:00
hathach
a37d2d64be
fix #143
2019-09-16 13:32:47 +07:00
Nathan Conrad
05c13342a3
Implement EP with size <64.
2019-09-15 23:51:42 -04:00
Nathan Conrad
18303e742e
Covert macros to inline functions.
2019-09-15 23:46:03 -04:00
Nathan Conrad
ae873a709e
Wrote TX instead of RX.
2019-09-15 23:33:36 -04:00
William D. Jones
6280e4e7cb
msp430f5529: Add empty msp_exp430f5529lp BSP and DCD.
2019-09-14 18:02:17 -04:00
Nathan Conrad
4ea212a432
This demonstrates that I don't pre-build things before committing them... oops.
2019-09-13 23:52:43 -04:00
Nathan Conrad
c831311a12
Off-by-one error in Synopsys assertions. (and move some braces to their own lines.
2019-09-13 23:38:58 -04:00
hathach
986beda9eb
adding stm32l4 support, board test run with stm32l476disco, usb doens't work yet
2019-09-13 11:22:44 +07:00
hathach
ff7261600c
ported stm32f2, added board stm32f207zg nucleo
...
close #127
2019-09-12 10:41:03 +07:00
Nathan Conrad
d3507b0787
Merge remote-tracking branch 'origin/master' into stfsdev_cleanups
2019-09-11 20:36:48 -04:00
Nathan Conrad
3326b9d008
Use types with explicit bit widths.
2019-09-11 20:33:47 -04:00
hathach
7f166d860d
stm32f7 work with dcd synopsis
...
close #124
2019-09-11 22:48:07 +07:00
Nathan Conrad
7b93177890
Use TU_VERIFY_STATIC, use more uint instead of uint8_t/uint16_t. Create reg16_clear_bits function to reduce typec conversion warnings.
2019-09-11 09:45:48 -04:00
Nathan Conrad
784dc52b62
Update header comments.
2019-09-11 09:44:25 -04:00
Nathan Conrad
4cf2b30759
Fix bug where the EPREGs were not being initialized as expected.
2019-09-11 09:43:57 -04:00
hathach
678ba586df
Merge pull request #122 from cr1901/synopsys
...
Synopsys Refactor
2019-09-11 10:37:49 +07:00
Nathan Conrad
4f6bedeac9
Rename the STM32 MCU options.
2019-09-10 12:57:43 -04:00
Nathan Conrad
23d39f2b15
Remove OPT_MCU_STM for L and G series.
2019-09-10 12:13:36 -04:00
Nathan Conrad
65e72de7ce
Move interrupt handler into device driver, and rename the OPT_MCU_STM32 constants.
2019-09-10 09:35:52 -04:00
Nathan Conrad
49c58be4ce
Fix silly typo in the F3xx support.
2019-09-10 01:31:14 -04:00
Nathan Conrad
bc2a65b20b
A few bug fixes, remove the unstested device notices, note supported boards in READMEs, and implement PMA
...
access stride (used on MCU's with 512 byte USB buffers).
2019-09-10 01:03:24 -04:00
Nathan Conrad
f7b0aeec52
Start clock on F0 and F0, and handle USB interrupts.
2019-09-09 19:20:26 -04:00
Nathan Conrad
d1976a30b3
Update F3 BSP and create F070RB BSP. Both are untested (but compile).
2019-09-09 16:14:38 -04:00
Nathan Conrad
5ec59c2a30
Add STM32 FSDEV driver.
2019-09-09 14:55:39 -04:00
Nathan Conrad
b4c8a09f20
Remove STM32 F3 port.
2019-09-09 13:29:26 -04:00
William D. Jones
1385d7c494
stm32: Refactor so F4 and H7 use a single Synopsys IP source file.
2019-09-09 10:48:14 -04:00
William D. Jones
82cd4b5350
dcd_stm32f4: Merge relevant changes from dcd_stm32h7.
2019-09-09 10:27:46 -04:00
William D. Jones
3efc81b285
dcd_stm32h7: Merge relevant changes from dcd_stm32f4. USB2 -> USB works as alias.
2019-09-09 10:14:20 -04:00
hathach
e123cad7bb
enhance dcd stm32f4 to support max 4 or 6 endpoints on 407 or 412
2019-09-08 23:10:51 +07:00
hathach
4663f9084d
ported board stm32f412g discovery
...
- added soft connect for enable pull up register dcd stm32f4
2019-09-08 21:57:02 +07:00
hathach
56f1ccd68a
fix #97
2019-09-05 21:59:19 +07:00
hathach
143a138028
Merge pull request #116 from hathach/develop
...
Board update
2019-09-05 16:18:34 +07:00
hathach
a90e2aa2ce
55s69 device work with usb0
2019-09-05 16:12:13 +07:00
hathach
7350e9c25c
Merge pull request #114 from cr1901/stm32h7
...
STM32H7 Support
2019-09-05 15:29:13 +07:00
William D. Jones
8f8ca77a91
stm32h7: Mark USB FIFOs as volatile, otherwise optimizations will remove
...
reads/writes to the FIFOs.
2019-09-04 01:06:07 -04:00
William D. Jones
910fd867c7
stm32h7: Fix indentation error where OUT XFER interrupt wasn't handled
...
in the correct scope.
2019-09-03 01:37:44 -04:00
William D. Jones
1a3dc9cba1
stm32h7: USB_OTG_FS -> USB2_OTG_FS.
2019-09-03 01:28:41 -04:00
William D. Jones
f703a74daa
stm32h7: Implement STALL logic for endpoints.
2019-09-03 01:28:41 -04:00
William D. Jones
28b131ea94
stm32h7: Implement dcd_edpt_open. cdc_msc_hid demo functional.
2019-09-03 00:37:50 -04:00
William D. Jones
d4302dacc5
stm32h7: Fix accidental overwrite of STUPCNT field in DOEPTSIZ register.
2019-09-03 00:25:21 -04:00
William D. Jones
9210167603
stm32h7: Implement dcd_set_address.
2019-09-02 21:00:30 -04:00
William D. Jones
0d0b802ee0
stm32h7: Implement IN and OUT receive for EP0; device descriptor returned.
2019-09-02 19:32:11 -04:00
William D. Jones
f602534536
stm32h7: Implement setup packet events.
2019-09-02 13:34:33 -04:00
hathach
074681da8b
dma of lpc54114 can also execute up to 64 bytes each transfer
...
There is still issue with cdc_msc_hid example
2019-09-01 17:05:34 +07:00
hathach
aeea6754af
rename lpc_usbd to lpc_ip3511
2019-09-01 16:44:40 +07:00
hathach
3067809957
adding lpc54xxx to dcd, able to go through enumeration
2019-09-01 16:15:23 +07:00
hathach
957201fc58
fix undef __ARM_ARCH_6M__
2019-09-01 11:59:50 +07:00
hathach
2d041aaa1d
clean up
2019-09-01 08:11:22 +07:00
hathach
30f707cad2
rename lpc11_13_15 to simply lpc_usbd since it is almost used by in recent year for nxp mcu
2019-09-01 00:51:58 +07:00
hathach
bac75a81fd
support LPC51u68 #100
2019-08-31 22:44:08 +07:00
William D. Jones
8b165e1024
stm32h7: Ensure FS (and the only) PHY is selected for OTG_HS2.
2019-08-30 22:07:35 -04:00
William D. Jones
7153561984
stm32h7: Enable USB peripheral (device does not enumerate yet).
2019-08-30 21:57:06 -04:00
William D. Jones
0fb9ab9a09
stm32h7: Add empty template cdc_msc_hid example for STM32H743 Nucleo board that compiles.
2019-08-24 12:40:18 -04:00
hathach
47cd08d526
clean up
2019-08-05 22:31:41 +07:00
hathach
d1df041519
nrf5x remove the depenedent on nrfx_power.h
2019-08-05 22:09:37 +07:00
hathach
d211035a0a
merge dcd/hal_nrf5x.c into dcd/dcd_nrf5x.c
2019-08-05 21:54:20 +07:00
hathach
ed6fa460e9
stm32 minor change
2019-07-19 10:59:35 +07:00
hathach
f16ebd512b
indent clean up
2019-07-04 18:45:10 +07:00
hathach
73d7ab201e
remove dcd_edpt_busy()
2019-06-10 22:29:18 +07:00
hathach
13e01c7dca
add TU_ prefix to compiler ATTR to prevent name conflict with application
2019-06-06 10:39:37 +07:00
hathach
3e6d911ce9
more clean up use inline bit funciton instead of macros
2019-05-14 12:54:29 +07:00
hathach
61ec407752
update license year to 2019
2019-05-14 11:48:05 +07:00
hathach
667133304b
fix samd dcd_clear_stall also reset data toggle
2019-05-10 00:10:18 +07:00
hathach
77bc421359
fix clear stall usage, fix reset data toggle with dcd_clear_stall for nrf52
2019-05-09 23:31:18 +07:00
hathach
2050778763
clean up
2019-05-01 20:41:26 +07:00
hathach
64bed848d0
fix #53 use nrfx_usbd_errata.h
2019-04-08 17:36:12 +07:00
hathach
dd9c441a61
samd support suspend and resume. Though cannot distinguish between Suspend and Disconnect
...
should work with #47
2019-04-02 02:14:22 +07:00
hathach
06e1fac7c5
nrf5x enable suspend after set address, instead of set config
2019-04-02 01:20:34 +07:00
hathach
2cc4ab2aef
nrf5x added LOWPOWER when suspend/resume
2019-03-31 23:57:38 +07:00
hathach
eabfc53f38
added tud_suspended() and tud_ready()
2019-03-30 23:01:23 +07:00
hathach
b28cc6ddb1
added dcd_remote_wakeup() stub for all ports
2019-03-30 14:47:11 +07:00
hathach
93a853cd5b
usbd add connected, suspended, remote_wakeup
...
- remove use of osal_queue_reset
2019-03-30 02:26:15 +07:00
hathach
1c2beba85c
working on suspend and resume
...
change dcd_init signature
2019-03-29 16:23:00 +07:00
hathach
0bdd4bd550
added Suspend and Resume event for nrf5x port
...
also rename DCD_EVENT_SUSPENDED to DCD_EVENT_SUSPEND
2019-03-29 01:34:53 +07:00
hathach
1e9848d917
replace dcd_edpt_(clear)stall by usbd_edpt_(clear)stall
...
- remove dcd_edpt_stalled() from dcd porting
2019-03-27 16:09:49 +07:00
hathach
4722376654
remove dcd_get_frame_number()
2019-03-27 01:01:48 +07:00
hathach
18f248b142
remove tusb_hal_millis() usage, less work for porting
2019-03-24 01:19:32 +07:00
hathach
43eb1a8b16
added stub for dcd_stm32f3
2019-03-22 23:57:56 +07:00
hathach
ba1bea5d53
simplify board API, adding stm32f3 discovery
...
- remove board header since it is not used
2019-03-22 22:06:48 +07:00
hathach
da55610f43
clean up
2019-03-20 20:19:21 +07:00
hathach
c211ee19dd
migrate license from BSD 3 clause to MIT
2019-03-20 16:11:42 +07:00
hathach
f932cf3854
stm32 update fifo in comment
2019-03-17 15:16:52 +07:00
hathach
5e92d67015
stm32 update TX Fifo for edpt IN, both CDC + MSC work great
...
- call dcd_event_xfer_complete() when enough bytes received
- add dcd_get_frame_number()
2019-03-15 18:43:09 +07:00
hathach
eda56769b9
dcd_set_address include status response, usbd control stall both control in and out
2019-03-13 23:14:48 +07:00
hathach
195a44172a
update stm32 dcd stall control endpoint
2019-03-13 16:54:10 +07:00
hathach
8418cb816b
Merge branch 'master' into stm32f4
2019-03-05 05:45:42 -08:00
William D. Jones
c95ad426c6
stm32f4: Refactor IN and OUT endpoint interrupt handling into their own functions.
2019-02-27 11:01:08 -05:00
William D. Jones
f43161353c
stm32f4: Refactor RX FIFO read into its own function; remove RXFLVL
...
resetting (read only) and masking (no nested ints).
2019-02-27 10:39:37 -05:00
William D. Jones
c51b11f103
Move all paths using "stm" to "st" subdirectories, update config.mk.
2019-02-27 09:15:07 -05:00
William D. Jones
5a1c5cf0b7
stm32f4: Clarify comments and disable OTGINT; fixes stack reset on
...
cable disconnect, and we don't use OTG right now.
2019-02-14 23:41:16 -05:00
William D. Jones
5a34a9de69
stm32f4: Implement STALL logic for endpoints.
2019-02-08 16:46:12 -05:00