6d86db3977
rename edpt_dir/number/addr to tu_edpt_*
2018-12-12 11:51:31 +07:00
e3514b8054
rename hcd_device_remove to hcd_device_close
2018-12-12 11:34:09 +07:00
607658d047
rename MODE_HOST_SUPPORTED to TUSB_OPT_HOST_ENABLED
2018-12-07 23:38:52 +07:00
e019916263
clean up ehci, support only 1 controller
2018-12-07 23:35:42 +07:00
2aa21a14e6
lpc17 ohci failed to execute control transfer !!
2018-12-07 18:49:26 +07:00
d524da0c94
enable all warnings
2018-12-07 14:49:55 +07:00
2fa32bd949
able to build host lpc18xx
2018-12-05 20:39:52 +07:00
9f3e91a934
update nrf errata
2018-12-05 14:30:47 +07:00
a73017fdc2
hal clean up
...
- replace tusb_hal_int_enable/disable to dcd_int_enable/disable,
hcd_int_enable/disable
- remove tusb_hal_init(), this will be part of dcd_init/hcd_init,
anything beyond dcd/hcd should be inited by bsp
2018-12-05 13:20:25 +07:00
6048a3bff4
remove dcd_connect/disconnect since there is no usage now
2018-12-05 12:22:33 +07:00
c1336dff03
lpc move Chip_USB_Init() out of stack to bsp
2018-12-05 11:53:56 +07:00
9176b7b1da
renane file
2018-12-05 08:51:11 +07:00
dd9c7b4249
lpc40xx device work, moving Chip_USB_Init out of tinyusb
2018-12-05 08:47:23 +07:00
fe8346e642
move pinmux out of dcd into bsp
2018-12-04 18:38:01 +07:00
6c2404ca49
adding ea4088 quickstart, able to blink
2018-12-04 16:32:20 +07:00
261e0f9801
adding lpc40xx support
2018-12-04 16:06:50 +07:00
7120e12971
add mcb1800, blink led ok
2018-12-04 13:17:12 +07:00
bf5ac608ff
rename dcd 18 43
2018-12-04 12:47:58 +07:00
1d6bbd9990
clean up dcd 43
2018-12-03 23:18:51 +07:00
29f721ba2c
dcd lpc43 clean up
2018-12-03 23:06:28 +07:00
9fec39d893
use lpcopen for lpc43x, work well
2018-12-03 22:58:21 +07:00
bb7123eed1
use lpcopen for ea4357, blinky ok
2018-12-03 21:22:11 +07:00
7f55bbaf05
clean up
2018-12-03 18:32:06 +07:00
9e33f19378
clean up
2018-12-03 17:47:37 +07:00
63faea3929
migrate lpc17 to lpcopen, usb device work ok
2018-12-03 17:43:16 +07:00
66bd9f0a16
wrap up lpc11u port
2018-12-03 13:15:28 +07:00
f28a15a886
clean up dcd lpc11u
2018-12-03 12:31:03 +07:00
57f7c18d77
dcd lpc11u6x work with cdc + msc
2018-12-03 00:04:55 +07:00
5848dd2895
lpc11u use USBSRAM, able to response with 1st request
2018-12-02 02:13:48 +07:00
fb842bb804
lp11u able to receive setup packet
2018-12-01 22:21:54 +07:00
d246cc2e6c
lpc13xx build ok (not work) with lpcopen
2018-11-30 23:39:18 +07:00
1f076bd945
rename cont
2018-11-30 12:59:23 +07:00
0ab62e6fa2
more rename
2018-11-30 12:57:44 +07:00
658c2ff570
rename
2018-11-30 12:56:09 +07:00
723e02780d
clean up
2018-11-30 12:51:54 +07:00
d96347a0f5
rename OPT_MCU_LPC13UXX to OPT_MCU_LPC13XX
2018-11-30 12:48:06 +07:00
522b0c11ef
move nvic prio in hal/dcd to bsp for portability
2018-11-29 22:59:00 +07:00
57b85262b2
added & tested lpc17xx freertos device example
...
- add USB priority check for freeRTOS config
2018-11-29 21:41:09 +07:00
15e4b97e36
lpc17xx add dcd_edpt_stalled
2018-11-29 20:09:02 +07:00
a76c5bf154
dcd lpc17xx, route control endpoint to EP_FAST
2018-11-29 19:58:17 +07:00
ed65a43977
clean up
2018-11-29 13:09:58 +07:00
402a5fee90
dcd lpc17xx enable EpIntEn for non-control IN after DMA complete
...
all transfer work well
2018-11-29 12:56:02 +07:00
c3140af274
correct TUD_OPT_HIGH_SPEED
2018-11-28 17:54:11 +07:00
772b2b692f
more dcd lpc17xx clean up
2018-11-28 17:31:15 +07:00
4a521d5085
clean up
2018-11-28 17:02:46 +07:00
04ad5da820
improve non-control xfer for lpc17xx
2018-11-28 16:53:36 +07:00
a3cc52829b
clean up
2018-11-27 23:55:10 +07:00
16b3f11d9f
clean up
2018-11-27 21:53:36 +07:00
15f704b623
improve dcd control lpc17xx
2018-11-27 21:51:02 +07:00
038851c362
enhance dcd lpc17xx. Able to pass enumeration
2018-11-27 20:48:46 +07:00
hathach