add test for mutex in test_osal_none.c
implement usbh_control_xfer using mutex to get access to queue xfer on control pipe
(while semaphore is used to sync with hcd DMA)
failed to issue control xfer: set idle & get report descriptor in hidh_open_subtask (more to work on)
add interface number to hidh_interface_info_t
refractor hidh_open_subtask to be a true subtask
cannot run with set idle code ON because of semaphore misuse
refractor usbh class driver indexing
opt out periodic list code in EHCI (need to refractor/group later)
[device lpc176x] rename dcd_endpoint_configure to dcd_pipe_open
add usbd_pipe_open to manage pipe
implementing dcd_lpc175x_6x.c
add usbd_dcd.h
add usbd_isr with TUSB_EVENT_SETUP_RECEIVED & TUSB_EVENT_BUS_RESET event
parameterize TUSB_CFG_DEVICE_CONTROL_PACKET_SIZE (replace USB_MAX_PACKET0)
--> able to get interrupt and receive setup packet, but SET ADDRESS (expected get device descriptor).
uncomment write zero length will cause issue, no more interrupt ?
add a bunch of stub header for dcd (175x_6x, 13xx, 18xx_43xx)
add dcd_nxp_romdriver for handling usb rom driver
add BIT_TEST_ in binary.h
remove mw_usbd_hid.h include due to lexical conflict
NOTES: print_greeting if is executed before the start of freeRTOS scheduler --> hardfault
- print_greeting->vsprintf->systick -> bunch of ISR --> hardfault.
printf using serial after the start of scheduler is ok though
- add new error enum TUSB_ERROR_OSAL_TASK_CREATE_FAILED
- move usbh_enumeration_task prototype to usbh.h
- change OSAL_SUBTASK_INVOKED_AND_WAIT behavior, will not "return" in calling task when subtask got error status.
calling task need to do that after the call
- osal_queue_receive signature from uint32_t* to void*
- implement osal_freertos.h for FreeRTOS 7.3 --> able to compile & build host_freertos
+ OSAL_TASK_FUNCTION
+ turn on FPU for M4 in both host_os_none & host_freertos (freertos requires FPU to be on to compile)
+ osal_task_create
+ OSAL_SUBTASK_INVOKED_AND_WAIT
+ SUBTASK_ASSERT
+ osal_semaphore_reset
+ osal_queue_flush
+ adding heap_1.c for memory management
implementing freeRTOS integration
change get_period_frame_list from using lst_idx to hostid (fix bug)
adding polling interval supported for interrupt: 1ms, 2ms, 4ms, 8ms
- add interval_ms to get_period_head function
- add bInterval to qhd_init
- add support for sub-frame (less than 8 micro frames) interval
- add bunch of test for interrupt different intervals
- add hal_debugger_is_attached & hal_debugger_breakpoint
- assert will suspend (place breakpoint) if the condition is failed and debugger is attached. Otherwise, a message to uart is printed
- fix get control qhd function when dev_addr is not zero (shifted 1)
- fix wrong logic for unsupported class
- add tests for pipe_close (while TDs are active)
- add tests for device unplugged
add tesst & implement the async_advance_isr to clean up "REMOVING" queue head
- add helper find previous qhd
- add remove qhd from async list
- add is_removing field for async advance isr to clean up
add pipe close for control pipe & bulk pipe (with tests)
add helper get qhd from pipe_handle
add osal_queue_send in usbh_device_plugged
add macro for placing breakpoint macros
fix ehci init:
- regs->cmd or (add run_stop)
- enable port power in portsc
add tusb_task_runner in main loop
fix binary.h compiler specific
add hal_init code to reset & set usbmode --> able to get USB ISR
remove const qualifier from return function of
- get_operational_register
- get_period_frame_list
- get_async_head
- get_period_head
- get_control_qhd
add stub for
- hcd_port_connect_status
- hcd_port_speed
hathach