hathach
706413f751
add tud_speed_get()
...
- define both fs and hs configuration descriptor
- rename CFG_TUD_CDC_EPSIZE to CFG_TUD_CDC_EP_BUFSIZE with default size of 64 for FS, and 512 for HS
2020-07-16 00:44:09 +07:00
Craig Hutchinson
323ae5a84f
Improve comment on CDC tud_cdc_write_available()
...
Fixes #460
2020-07-10 12:24:09 +01:00
Ha Thach
81392da1ea
Merge pull request #456 from me-no-dev/esp32-s2-epin-to
...
ESP32-S2: Detect EP IN Xfer Timeout
2020-07-10 12:29:06 +07:00
Ha Thach
dbced9911d
Merge pull request #447 from hathach/add-stm-hs
...
Add support for STM32 OTG HS core
2020-07-08 19:47:24 +07:00
hathach
0fd074afd8
change REDUCE_SPEED=0/1 to explicitly SPEED=high/full
...
update readme, boards.md to add link to new stm boards
2020-07-08 16:29:48 +07:00
Ha Thach
a192d99bf0
Merge pull request #457 from UweBonnes/add-stm-hs
...
Add stm hs
2020-07-05 14:07:08 +07:00
Uwe Bonnes
fd38178189
STM32/OTG_HS: Allow OTG_HS port to run at FS speed.
...
Add "REDUCE_SPEED=1" to the compile options.
2020-07-03 10:52:57 +02:00
hathach
ad5ae8c31d
update per review
2020-07-03 14:50:39 +07:00
hathach
a09a86d299
fix NVIC disable typo
2020-07-03 01:19:02 +07:00
me-no-dev
d493724a7b
ESP32-S2: Detect EP IN Xfer Timeout
...
In some rare ocasions (bad cable, noise, etc.) data transfer might timeout and hang the endpoint, unless the interrupt flag is cleared.
This pull request targets to solve that case.
2020-07-02 13:05:17 +03:00
hathach
4cec866994
correct HSE_VALUE in hal_conf
...
- although it is define in CFLAGS, it is worth to correct to be
consistent with other build
- extract set_speed()
2020-07-02 14:57:00 +07:00
hathach
9a290febcd
change default port some stm bsp
...
- f769disco default port is highspeed port1
- remove PORT0 on stlink since the board only populated HS connector
2020-07-02 11:58:40 +07:00
hathach
4966fb2e13
clean up
2020-07-02 01:25:21 +07:00
hathach
c2289777f7
Merge branch 'add-stm-hs' of github.com:hathach/tinyusb into add-stm-hs
2020-07-01 23:53:33 +07:00
Uwe Bonnes
196bdbc702
st/synopsys/dcd_synopsys.c: Remove USBC PHY PLL stabilization delay for now
...
While the ST code has a 2 ms stabilization delay for the USBC PHY PLL,
running without this delay showed no problem for at leat 10 USB un/replug
cycles. Observe for problems!
2020-07-01 14:45:07 +02:00
hathach
d2450abaaf
only set turnaround in reset complete
2020-07-01 18:51:04 +07:00
hathach
e3974d6869
correctly set turn around according to cpu clock
...
help to run with low speed mcu
2020-07-01 18:44:52 +07:00
hathach
a512a31c9d
Merge branch 'master' into add-stm-hs
2020-07-01 17:58:02 +07:00
hathach
ed1b670c55
clean up code
2020-07-01 17:57:37 +07:00
me-no-dev
6178f8de2f
ESP32-S2: Handle the fact that available EP IN FIFOs are less than the number of available EP INs
...
ESP32-S2 has only 5 available endpoint-in FIFOs (including EP0) but 7 available EP IN numbers. This change decouples the fifo number from the endpoint number, providing FIFO numbers until they reach the limit, at which point it will return false and assert an error that too many endpoints were allocated.
2020-07-01 13:38:59 +03:00
Ha Thach
0c9932440b
Merge pull request #452 from hathach/fix-dfu-rt
...
Fix dfu rt
2020-07-01 15:24:39 +07:00
hathach
12a145b27d
fix dfu-rt to response to SET_INTERFACE and DFU_GETSTATUS
...
fix #450
2020-07-01 01:33:02 +07:00
Jan Dümpelmann
378e6aab8c
Clear ep0_pending if rx short packet
2020-06-30 17:56:25 +02:00
Jan Dümpelmann
9e35ef73f7
Fix receiving of short packet data (ep out)
2020-06-30 12:55:39 +02:00
Uwe Bonnes
30a18e2605
stm32f723disco: USB HS enumerates.
2020-06-30 11:07:53 +02:00
Uwe Bonnes
05bfd9ac4a
dcd_synopsys: Handle HS and FS IP in one device
...
FIXME: Allow run-time selection to allow to handle both HS and FS with
one file
F746 HS port enumerates with error
config 1 interface 2 altsetting 0 bulk endpoint 0x3 has invalid maxpacket 64
2020-06-30 11:02:41 +02:00
hathach
ab75998316
Merge branch 'master' into add-stm-hs
2020-06-30 01:55:57 +07:00
Ha Thach
05996aee64
Merge pull request #427 from kasjer/kasjer/add-da1469x-support
...
Support for DA1469x MCU from Dialog Semiconductor
2020-06-30 01:20:56 +07:00
Ha Thach
268ab9eaa8
Merge pull request #399 from duempel/redesign_synopsys_receive
...
Improvements to Synopsys EP OUT
2020-06-29 16:02:40 +07:00
Jan Dümpelmann
99df7789a7
Add author name to dcd_synopsys.c
2020-06-29 10:55:03 +02:00
Jan Dümpelmann
4f69bcea7e
Remove EP0 remaining bytes manipulation
...
Renaming edpt_xact to edpt_schedule_packets
2020-06-26 17:18:25 +02:00
Jeff Epler
b2ef8cdd42
dcd_samd: Provide implementation for OPT_MCU_SAME5X
2020-06-25 18:51:04 -05:00
hathach
d4d6e06c1d
added OPT_MCU_SAME5X option
2020-06-24 00:53:17 +07:00
Gavin Li
7ae47a9397
Call tud_cdc_tx_cb right after flush to keep tx fifo full
2020-06-20 22:12:10 -07:00
Jan Dümpelmann
067287ef91
Add transaction (edpt_xact) as sub transfer
...
A transfer can have one or multiple transactions.
Usually only EP0 splits one xfer into multiple xact.
2020-06-18 17:18:28 +02:00
Mengsk
9ffb9b69a4
Disable SOF in dcd_stm32_fsdev
...
Signed-off-by: Mengsk <admin@hifiphile.com>
2020-06-18 14:18:00 +02:00
Gavin Li
8fe887198b
Add tx callback to cdc device
...
Useful for continuous transmission of data, which is difficult currently
because there is no notification of tx completion.
2020-06-18 01:13:44 -07:00
Mengsk
57b553e023
Fix IAR warnings.
...
Pa039 : use of address of unaligned structure member.
Pe188: enumerated type mixed with another type.
2020-06-17 10:08:33 +02:00
hathach
2b1c7730b7
fix hs port1 build with net endpoint
2020-06-16 00:53:06 +07:00
hathach
667eaa6dd6
fix stm32h743 priority with freeRTOS
2020-06-16 00:03:52 +07:00
hathach
2dd1be13e5
Enhance EP FIFO allocation for both Fullspeed and Highspeed
...
- Update shared RX FIFO calculation with FS/HS
- IN FIFO EP
- Interrupt -> use EPSize
- Bulk/ISO -> use max(EPSize, remaining-fifo / non-opened-EPIN)
2020-06-15 23:17:49 +07:00
Reinhard Panhuber
bc7e24b659
Fix wrong comment for IAD checks.
2020-06-14 14:22:10 +02:00
Jan Dümpelmann
4399dd1b06
cherry pick PR399 commit : Interrupt time improvements
2020-06-14 19:13:31 +07:00
hathach
f438aedccb
overwrite setup packet
2020-06-14 18:29:38 +07:00
hathach
95966c2201
improve usbd log for control transfer
2020-06-14 18:29:02 +07:00
hathach
a347de6e50
revert CFG_TUSB_RHPORT0_MODE to previous way
2020-06-14 18:28:45 +07:00
Reinhard Panhuber
b25bbf4776
Fix alignment.
2020-06-14 12:58:16 +02:00
Reinhard Panhuber
3012175351
Fix alignment.
2020-06-14 12:57:00 +02:00
Reinhard Panhuber
48b2e6cf78
Fix too strict checks on subclass and interface of iad descriptor.
2020-06-13 13:51:50 +02:00
Jerzy Kasenberg
0635bafe0a
Add DCD for Dialog DA1469x MCU
...
Dialog Semiconductor's BLE MCU DA1469x comes with full speed USB.
It's base on National Semiconductor discrete USB controller USBN9603/4.
This adds support for:
- control/interrupt/bulk endpoints (up to 64 bytes)
- ISO endpoint were not tested and may not work correctly
- reset/sleep/wakeup are handled
- code for VBUS changes is provided
2020-06-09 15:55:46 +02:00
hathach
e92118635c
adding speed detect on bus reset
2020-06-01 13:40:18 +07:00
hathach
710c54f8cb
allow hs ep open with 512 bytes
2020-06-01 01:36:09 +07:00
hathach
f771afe6af
fixed EP0 size to 64 since LS is not supported in device mode
...
- set turn-around and report actual speed in Enum Done
- add dcd_event_bus_reset() helper to report speed
2020-05-31 23:43:29 +07:00
hathach
5ffba8536d
able to detect as hs
2020-05-31 19:41:22 +07:00
Ha Thach
5efeaf2ac1
Merge pull request #413 from kasjer/kasjer/ble-over-usb
...
Bluetooth HCI transport over USB
2020-05-31 15:07:56 +07:00
hathach
d6d29897f3
add get device qualifier descriptor
2020-05-28 23:16:16 +07:00
Jerzy Kasenberg
56d46483e4
Add bt hci device class
...
Code implements USB transport for bluetooth HCI.
2020-05-28 10:58:49 +02:00
Jerzy Kasenberg
077437b3dc
Add non standard request handling in class
...
For some reason bluetooth stack implementations send class requests
to device instead of interface.
To implement HCI interface over USB non device addressed requests
for class need to be handled.
2020-05-28 10:11:37 +02:00
hathach
53b749fd72
check max_len for vendor and hid
2020-05-28 14:44:26 +07:00
hathach
fb214f7cf7
rename to drv_len to be consistent
2020-05-28 13:57:49 +07:00
hathach
10cd3f24bf
initial transfer failed in open() shouldn't cause the driver open to fail.
2020-05-28 13:48:02 +07:00
hathach
c1db36a15c
update vendor open()
2020-05-28 12:19:06 +07:00
hathach
bec5b5f9da
update usbtmc open()
2020-05-28 12:13:48 +07:00
hathach
13860e9f94
update net open()
2020-05-28 11:51:25 +07:00
hathach
8f560bf275
update midi open()
2020-05-28 11:41:37 +07:00
hathach
89a3d1f6d1
update hid open()
2020-05-28 11:19:12 +07:00
hathach
7a15d2e0d2
improve msc
2020-05-28 00:56:33 +07:00
hathach
2eeeda1bcf
change signature for dfu runtime
2020-05-28 00:46:32 +07:00
hathach
e340404968
changing usbd driver open() return type, add max_len
...
only done with cdc and msc, push this interim for feedback first
2020-05-27 19:01:59 +07:00
hathach
d4bf777c94
try to get synopsys work with OTG HS + external PHY
2020-05-27 11:01:33 +07:00
hathach
b4804d1592
random clean up for tdi
2020-05-26 22:15:38 +07:00
hathach
0482f0d686
update h743eval with rhport=1 highspeed
2020-05-26 22:15:00 +07:00
hathach
947c3eb10d
multiple port support for global otg base
2020-05-26 16:07:48 +07:00
hathach
b7ab60aa44
suporting multiple port (OTG FS + HS) for stm32
2020-05-26 15:52:02 +07:00
hathach
fad088719e
merge CFG_TUSB_RHPORT1_MODE into CFG_TUSB_RHPORT0_MODE
...
each port is 1 byte for easy maintenance
2020-05-26 15:21:23 +07:00
hathach
d108ea4326
implement hcd_uframe_number for ohci
...
able to get 8 byte descriptors using LPC1769 + base, but failed to reset
and set address.
2020-05-22 21:45:34 +07:00
hathach
f308990ab5
Merge branch 'master' into update-host
2020-05-22 15:28:22 +07:00
hathach
ff9994116e
fix nrf hanged (blocking wait) when called within critical section
2020-05-21 21:22:12 +07:00
hathach
8b66098335
fix freeRTOS logic
2020-05-20 15:21:11 +07:00
hathach
a0fe3a80e7
remove queue lock/unlock per review
2020-05-20 15:09:46 +07:00
hathach
d8a15aca77
remove osal_queue_t const qhdl from osal API
...
since it doesn't make any differences.
2020-05-20 14:38:34 +07:00
hathach
88a455a9b9
added tud_task_event_ready()
...
to check if there is pending events in the tud task without executing
it. Useful to check before entering low power mode with WFI/WFE
2020-05-20 14:31:45 +07:00
hathach
4e8d414bc6
added osal_queue_empty() API
...
ported for osal none/freertos/mynewt
2020-05-20 13:38:41 +07:00
hathach
58cedf4c06
usb0 host on mcb1800 work with fullspeed mode.
...
use usbh_edpt_open() to correctly map ep2drv[]
2020-05-19 00:55:43 +07:00
hathach
81b1f97ef7
suppress cast-align warnings for net device driver
2020-05-18 13:23:40 +07:00
hathach
550746097b
fix cast-align warning for nuc505
2020-05-18 13:03:41 +07:00
hathach
1a8ce043ed
enable -Wcast-align
...
suppress vendor sdk driver at board.mk
2020-05-17 14:24:15 +07:00
Jan Dümpelmann
42edbc0006
Allow EP0 to use xfer sizes larger than one packet
2020-05-15 22:26:14 +02:00
Jan Dümpelmann
28696de390
Interrupt time improvements
2020-05-15 18:21:44 +02:00
hathach
b0d49e55de
refactor copy to and from fifo
2020-05-14 14:24:55 +07:00
Mengsk
46875a3912
Optimize FIFO for byte transfer.
...
Signed-off-by: Mengsk <admin@hifiphile.com>
2020-05-13 23:54:23 +02:00
Ha Thach
4e6aa0d81d
Merge pull request #390 from hathach/detect-nrf-softdevice
...
detect if SD is actually present on the flash using SD magic
2020-05-12 14:35:45 +07:00
Jan Dümpelmann
3401e0f6ff
Synopsys OUT EP improvements:
...
- Use register based XFRSIZ to determine transfer complete
(xfer->queued_len and xfer->short_packet were deleted)
- Pop out as many RxFIFO data entries as available within a IRQ call
- less application interruption due to XFRC calls
2020-05-08 18:10:48 +02:00
Mengsk
f02ad1d0dc
Add IAR compiler attribute and endian support.
2020-05-08 13:29:33 +02:00
hathach
eeb076454b
add CFG_TUSB_DEBUG_PRINTF() for log retargeting
2020-05-08 12:56:32 +07:00
Ha Thach
f9f0873b72
Merge pull request #393 from xobs/fix-debug-warning
...
device: fix build warning when CFG_TUSB_DEBUG >= 2
2020-05-08 12:38:50 +07:00
Sean Cross
63bd8d2e44
device: fix build warning when CFG_TUSB_DEBUG >= 2
...
The function is defined inside of a function body which generates a
warning. Circuit Python treats these warnings as errors, and so
refuses to build with debugging enabled:
../../lib/tinyusb/src/device/usbd_control.c: In function 'usbd_control_xfer_cb':
../../lib/tinyusb/src/device/usbd_control.c:195:19: error: nested extern declaration of 'usbd_driver_print_control_complete_name' [-Werror=nested-externs]
195 | extern void usbd_driver_print_control_complete_name(bool (*control_complete) (uint8_t, tusb_control_request_t const *));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make: *** [../../py/mkrules.mk:55:
build-simmel/lib/tinyusb/src/device/usbd_control.o] Error 1
Move the declaration to the top of the function to silence this warning.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-05-07 19:03:40 +08:00
hathach
58b99e59d4
detect if SD is actually present on the flash using SD magic
...
even with SOFTDEVICE_PRESENT defined, SD may not be present on actual
flash.
2020-05-05 23:07:56 +07:00
Ha Thach
101f234a16
Merge pull request #387 from duempel/redesign_transmit_synopsys
...
Redesign of Synopsys device transmission
2020-05-04 14:41:20 +07:00
hathach
905a80d1b2
temporarily remove osal_task_delay() from osal
...
- add hcd_uframe_number() API, update EHCI to return uframe number
- get host running on ea4357
2020-05-04 14:11:58 +07:00