port 318LPW1K-L code for ACT-34B remote
This commit is contained in:
parent
84e3c79435
commit
011b6edeab
|
@ -0,0 +1,174 @@
|
||||||
|
/* micro-controller firmware fot the Linear ACT-34B remote
|
||||||
|
Copyright (C) 2014 Kévin Redon <kingkevin@cuvoodoo.info>
|
||||||
|
|
||||||
|
This program is free software; you can redistribute it and/or modify
|
||||||
|
it under the terms of the GNU General Public License as published by
|
||||||
|
the Free Software Foundation; either version 3 of the License, or
|
||||||
|
(at your option) any later version.
|
||||||
|
|
||||||
|
This program is distributed in the hope that it will be useful,
|
||||||
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||||
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||||
|
GNU General Public License for more details.
|
||||||
|
|
||||||
|
You should have received a copy of the GNU General Public License
|
||||||
|
along with this program; if not, write to the Free Software Foundation,
|
||||||
|
Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
|
||||||
|
*/
|
||||||
|
/* libraries */
|
||||||
|
#define __12f617
|
||||||
|
#include <pic12f617.h>
|
||||||
|
#include <stdint.h>
|
||||||
|
|
||||||
|
/* the peripherals connected to the pins */
|
||||||
|
#define SWITCH1 _GP0
|
||||||
|
#define SWITCH2 _GP3
|
||||||
|
// note: SWITCH3 will behave as pressed when SWITCH4 is pressed
|
||||||
|
#define SWITCH3 _GP1
|
||||||
|
#define SWITCH4 _GP2
|
||||||
|
// note: CLOCK will be enable also if only TX is enabled
|
||||||
|
#define CLOCK _GP5
|
||||||
|
#define TX _GP4
|
||||||
|
|
||||||
|
/* simple functions */
|
||||||
|
#define clock_on() GPIO |= CLOCK;
|
||||||
|
#define clock_off() GPIO &= ~CLOCK;
|
||||||
|
#define tx_on() GPIO |= TX;
|
||||||
|
#define tx_off() GPIO &= ~TX;
|
||||||
|
#define sleep() __asm sleep __endasm
|
||||||
|
|
||||||
|
/* variables */
|
||||||
|
// a megacode is 3 bytes long (MSB of byte 1 is 1)
|
||||||
|
# define CODE 0xc917c2
|
||||||
|
// transmitting (0: do not transmit, 1: transmit, -1: finish transmiting)
|
||||||
|
volatile int8_t transmit = 0;
|
||||||
|
// the 4 phases of the bit (2ms pause, 1ms pulse, 2ms pause, 1ms pulse. only transmit during one of the two pulse periode depending on the bit value)
|
||||||
|
volatile uint8_t phase = 0;
|
||||||
|
// save the GPIO state to be able to figure out which changed
|
||||||
|
volatile last_gpio = GPIO;
|
||||||
|
|
||||||
|
/* configuration bits */
|
||||||
|
uint16_t __at(_CONFIG) __CONFIG = _WRT_OFF & // entire memory write protected
|
||||||
|
_BOREN_OFF & // brown-out reset off
|
||||||
|
_IOSCFS_4MHZ & // set internal oscillator to 4MHz
|
||||||
|
_CP_OFF & // no code protection
|
||||||
|
_MCLRE_OFF & // disable master clear reset
|
||||||
|
_PWRTE_ON & // enable power-up timer
|
||||||
|
_WDTE_OFF & // disable watchdog
|
||||||
|
_INTRC_OSC_NOCLKOUT; // use internal oscillator and both I/O pins
|
||||||
|
|
||||||
|
/* set timer in ms */
|
||||||
|
#define TICKS_PER_MS 125UL // the number of timer 1 ticks to wait for 1ms, using the internal 4MHz clock and a prescaler of 8, and hand tuning
|
||||||
|
|
||||||
|
void timer_1ms() {
|
||||||
|
TMR1ON = 0; // disable timer 1 (to write value safely)
|
||||||
|
TMR1L = (0xffff-1*TICKS_PER_MS); // set time
|
||||||
|
TMR1H = (0xffff-1*TICKS_PER_MS)>>8; // set time
|
||||||
|
TMR1ON = 1; // start timer 1
|
||||||
|
}
|
||||||
|
|
||||||
|
void timer_2ms() {
|
||||||
|
TMR1ON = 0; // disable timer 1 (to write value safely)
|
||||||
|
TMR1L = (0xffff-2*TICKS_PER_MS); // set time
|
||||||
|
TMR1H = (0xffff-2*TICKS_PER_MS)>>8; // set time
|
||||||
|
TMR1ON = 1; // start timer 1
|
||||||
|
}
|
||||||
|
|
||||||
|
/* transmit the megacode */
|
||||||
|
void megacode (void) {
|
||||||
|
uint8_t bit = phase/4;
|
||||||
|
if (transmit != 0) {
|
||||||
|
if (bit<24) { // transmit bit
|
||||||
|
if (phase%2) {
|
||||||
|
uint8_t pulse = (CODE>>(23-bit))&0x01;
|
||||||
|
if ((phase%4==1 && !pulse) || (phase%4==3 && pulse)) {
|
||||||
|
tx_on();
|
||||||
|
}
|
||||||
|
timer_1ms();
|
||||||
|
} else {
|
||||||
|
tx_off();
|
||||||
|
timer_2ms();
|
||||||
|
}
|
||||||
|
} else if (bit==24) { // 25th bit is a blank
|
||||||
|
tx_off();
|
||||||
|
timer_2ms();
|
||||||
|
} else { // restart after 25th bit
|
||||||
|
phase = 0xff; // phase will be 0 after incrementing
|
||||||
|
if (transmit == -1) { // stop transmiting if requested
|
||||||
|
transmit = 0; // stop transmiting
|
||||||
|
clock_off(); // stop clock
|
||||||
|
}
|
||||||
|
timer_1ms();
|
||||||
|
}
|
||||||
|
phase++; // go to next phase
|
||||||
|
}
|
||||||
|
}
|
||||||
|
|
||||||
|
/* initialize micro-conroller */
|
||||||
|
void init (void) {
|
||||||
|
ANSEL = 0; // all pins are digital
|
||||||
|
TRISIO |= SWITCH1|SWITCH2|SWITCH3|SWITCH4; // switches are inputs (per default)
|
||||||
|
TRISIO &= ~(CLOCK|TX); // all other are outputs
|
||||||
|
NOT_GPPU = 0; // enable global weak pull-up for inputs
|
||||||
|
WPU |= SWITCH1|SWITCH3|SWITCH4; // use internal pull-up on switches (the external are weak)
|
||||||
|
// SWITCH2 pull-up is not enabled because pins is not used as MCLR
|
||||||
|
GPIO &= ~(CLOCK|TX); // clear output
|
||||||
|
|
||||||
|
IOC |= (SWITCH1|SWITCH2|SWITCH3|SWITCH4); // enable interrupt for the switches
|
||||||
|
GPIE = 1; // enable interrupt on GPIO
|
||||||
|
last_gpio = GPIO; // save current state
|
||||||
|
|
||||||
|
T1CON = _T1CKPS1 | _T1CKPS0; // set prescaler to 8
|
||||||
|
// 0 is set per default, but just be sure
|
||||||
|
TMR1ON = 0; // stop timer 1
|
||||||
|
TMR1GE = 0; // enable timer 1
|
||||||
|
TMR1CS = 0; // use internal clock / 4 (=1MHz)
|
||||||
|
TMR1IF = 0; // clear interrupt
|
||||||
|
PIE1 = 1; // enable timer 1 interrupt
|
||||||
|
PEIE = 1; // enable timer interrupt
|
||||||
|
|
||||||
|
GIE = 1; // enable interrups
|
||||||
|
|
||||||
|
}
|
||||||
|
|
||||||
|
// funcion called on interrupts
|
||||||
|
// interrupt 0 is only one on PIC12
|
||||||
|
static void interrupt(void) __interrupt 0
|
||||||
|
{
|
||||||
|
if (GPIF) { // pin state changed
|
||||||
|
last_gpio ^= GPIO; // figure out which GPIO changed
|
||||||
|
if (last_gpio&SWITCH2) { // switch 1 (bigger button on top right) changed
|
||||||
|
if (GPIO&SWITCH2) { // button released, stop transmission
|
||||||
|
if (transmit == 1) { // currently transmitting
|
||||||
|
transmit = -1; // stop transmitting after last transmition
|
||||||
|
}
|
||||||
|
} else { // switch is pressed, start transmission
|
||||||
|
if (transmit == 0) { // only transmit if code is loaded
|
||||||
|
transmit = 1; // start transmission procedure
|
||||||
|
phase = 0; // start from beginning
|
||||||
|
clock_on(); // start clock and leave it on during the whole transmission
|
||||||
|
megacode(); // start sending megacode
|
||||||
|
}
|
||||||
|
}
|
||||||
|
}
|
||||||
|
last_gpio = GPIO; // save current state
|
||||||
|
GPIF = 0; // clear interrupt
|
||||||
|
}
|
||||||
|
if (TMR1IF) { // timer 1 overflow
|
||||||
|
megacode(); // continue sending megacode
|
||||||
|
TMR1IF = 0; // clean interrupt
|
||||||
|
}
|
||||||
|
|
||||||
|
}
|
||||||
|
|
||||||
|
void main (void)
|
||||||
|
{
|
||||||
|
init(); // configure micro-controller
|
||||||
|
transmit = 0; // disable transmission initialy
|
||||||
|
|
||||||
|
while (1) { // a microcontroller runs forever
|
||||||
|
if (transmit == 0) {
|
||||||
|
// sleep(); // sleep to save power. this will shut down timer 1, but button press will wake it up
|
||||||
|
}
|
||||||
|
}
|
||||||
|
}
|
|
@ -0,0 +1,32 @@
|
||||||
|
# variables
|
||||||
|
TARGET = ACT-34B
|
||||||
|
PIC = 12f617
|
||||||
|
# software verion used:
|
||||||
|
# pk2cmd: 1.21
|
||||||
|
# sdcc: 3.4.0
|
||||||
|
# gputils: 1.3.0
|
||||||
|
|
||||||
|
all: off flash on
|
||||||
|
|
||||||
|
# flash program
|
||||||
|
flash: $(TARGET).hex
|
||||||
|
pk2cmd -PPIC$(PIC) -F$< -M
|
||||||
|
|
||||||
|
# power on remote
|
||||||
|
on:
|
||||||
|
pk2cmd -PPIC$(PIC) -T
|
||||||
|
|
||||||
|
# power off remote
|
||||||
|
off:
|
||||||
|
pk2cmd -PPIC$(PIC) -V0
|
||||||
|
|
||||||
|
# compile program
|
||||||
|
compile: $(TARGET).hex
|
||||||
|
|
||||||
|
# compile program C source code (includes a default code)
|
||||||
|
$(TARGET).hex: $(TARGET).c
|
||||||
|
sdcc --std-c99 --opt-code-size --use-non-free -mpic14 -p$(PIC) $<
|
||||||
|
|
||||||
|
# remove temporary files
|
||||||
|
clean:
|
||||||
|
rm -f $(TARGET).hex $(TARGET).lst $(TARGET).asm $(TARGET).adb $(TARGET).o $(TARGET).cod
|
Loading…
Reference in New Issue