correct LED, button and uart for feather_stm32f405
This commit is contained in:
hathach
parent
3c49ff153e
commit
943b7467d8
|
|
@ -20,7 +20,8 @@ SRC_C += \
|
|||
$(ST_HAL_DRIVER)/Src/stm32f4xx_hal.c \
|
||||
$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_cortex.c \
|
||||
$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_rcc.c \
|
||||
$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_gpio.c
|
||||
$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_gpio.c \
|
||||
$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_uart.c
|
||||
|
||||
SRC_S += \
|
||||
$(ST_CMSIS)/Source/Templates/gcc/startup_stm32f405xx.s
|
||||
|
|
@ -46,5 +47,5 @@ JLINK_IF = swd
|
|||
STM32Prog = STM32_Programmer_CLI
|
||||
|
||||
# flash target using on-board stlink
|
||||
flash: $(BUILD)/$(BOARD)-firmware.elf
|
||||
$(STM32Prog) --connect port=swd --write $< --go
|
||||
flash: $(BUILD)/$(BOARD)-firmware.bin
|
||||
dfu-util -R -a 0 --dfuse-address 0x08000000 -D $<
|
||||
|
|
|
|||
|
|
@ -31,7 +31,7 @@
|
|||
|
||||
// Blue LED is chosen because the other LEDs are connected to ST-LINK lines.
|
||||
#define LED_PORT GPIOC
|
||||
#define LED_PIN GPIO_PIN_4
|
||||
#define LED_PIN GPIO_PIN_1
|
||||
#define LED_STATE_ON 1
|
||||
|
||||
// Pin D5
|
||||
|
|
@ -39,6 +39,24 @@
|
|||
#define BUTTON_PIN GPIO_PIN_7
|
||||
#define BUTTON_STATE_ACTIVE 0
|
||||
|
||||
#define UARTx USART3
|
||||
#define UART_GPIO_PORT GPIOB
|
||||
#define UART_GPIO_AF GPIO_AF7_USART3
|
||||
#define UART_TX_PIN GPIO_PIN_10
|
||||
#define UART_RX_PIN GPIO_PIN_11
|
||||
|
||||
UART_HandleTypeDef UartHandle;
|
||||
|
||||
|
||||
// enable all LED, Button, Uart, USB clock
|
||||
static void all_rcc_clk_enable(void)
|
||||
{
|
||||
__HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D-
|
||||
__HAL_RCC_GPIOC_CLK_ENABLE(); // LED, Button
|
||||
__HAL_RCC_GPIOB_CLK_ENABLE(); // Uart tx, rx
|
||||
__HAL_RCC_USART3_CLK_ENABLE(); // Uart module
|
||||
}
|
||||
|
||||
/**
|
||||
* @brief System Clock Configuration
|
||||
* The system Clock is configured as follow :
|
||||
|
|
@ -104,14 +122,13 @@ void board_init(void)
|
|||
#endif
|
||||
|
||||
SystemClock_Config();
|
||||
|
||||
// Notify runtime of frequency change.
|
||||
SystemCoreClockUpdate();
|
||||
|
||||
all_rcc_clk_enable();
|
||||
|
||||
GPIO_InitTypeDef GPIO_InitStruct;
|
||||
|
||||
// LED
|
||||
__HAL_RCC_GPIOC_CLK_ENABLE();
|
||||
GPIO_InitStruct.Pin = LED_PIN;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
||||
GPIO_InitStruct.Pull = GPIO_PULLUP;
|
||||
|
|
@ -121,19 +138,25 @@ void board_init(void)
|
|||
board_led_write(false);
|
||||
|
||||
// Button
|
||||
//__HAL_RCC_GPIOC_CLK_ENABLE();
|
||||
GPIO_InitStruct.Pin = BUTTON_PIN;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
|
||||
GPIO_InitStruct.Pull = GPIO_PULLUP;
|
||||
GPIO_InitStruct.Speed = GPIO_SPEED_FAST;
|
||||
HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct);
|
||||
|
||||
// Uart
|
||||
GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
|
||||
GPIO_InitStruct.Pull = GPIO_PULLUP;
|
||||
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
|
||||
GPIO_InitStruct.Alternate = UART_GPIO_AF;
|
||||
HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct);
|
||||
|
||||
// Enable USB OTG clock
|
||||
__HAL_RCC_USB_OTG_FS_CLK_ENABLE();
|
||||
|
||||
// USB Pin Init
|
||||
// PA9- VUSB, PA10- ID, PA11- DM, PA12- DP
|
||||
__HAL_RCC_GPIOA_CLK_ENABLE();
|
||||
|
||||
/* Configure DM DP Pins */
|
||||
GPIO_InitStruct.Pin = GPIO_PIN_11 | GPIO_PIN_12;
|
||||
|
|
@ -180,8 +203,8 @@ int board_uart_read(uint8_t* buf, int len)
|
|||
|
||||
int board_uart_write(void const * buf, int len)
|
||||
{
|
||||
(void) buf; (void) len;
|
||||
return 0;
|
||||
HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff);
|
||||
return len;
|
||||
}
|
||||
|
||||
#if CFG_TUSB_OS == OPT_OS_NONE
|
||||
|
|
|
|||
|
|
@ -75,7 +75,7 @@
|
|||
/* #define HAL_MMC_MODULE_ENABLED */
|
||||
/* #define HAL_SPI_MODULE_ENABLED */
|
||||
/* #define HAL_TIM_MODULE_ENABLED */
|
||||
/* #define HAL_UART_MODULE_ENABLED */
|
||||
#define HAL_UART_MODULE_ENABLED
|
||||
/* #define HAL_USART_MODULE_ENABLED */
|
||||
/* #define HAL_IRDA_MODULE_ENABLED */
|
||||
/* #define HAL_SMARTCARD_MODULE_ENABLED */
|
||||
|
|
@ -199,6 +199,8 @@
|
|||
#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */
|
||||
#define USE_HAL_SWPMI_REGISTER_CALLBACKS 0U /* SWPMI register callback disabled */
|
||||
#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */
|
||||
#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */
|
||||
#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */
|
||||
#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */
|
||||
|
||||
/* ########################## Assert Selection ############################## */
|
||||
|
|
|
|||
|
|
@ -43,9 +43,9 @@
|
|||
#define UART_TX_PIN GPIO_PIN_9
|
||||
#define UART_RX_PIN GPIO_PIN_10
|
||||
|
||||
|
||||
UART_HandleTypeDef UartHandle;
|
||||
|
||||
|
||||
// enable all LED, Button, Uart, USB clock
|
||||
static void all_rcc_clk_enable(void)
|
||||
{
|
||||
|
|
|
|||
Loading…
Reference in New Issue