fix ci, remove use of CFG_TUSB_RHPORT0_MODE in bsp

hw/bsp/ea4088qs/ea4088qs.c

@@ -32,11 +32,11 @@
 //--------------------------------------------------------------------+
 void USB_IRQHandler(void)
 {
-  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST
+  #if CFG_TUD_ENABLED
     tuh_int_handler(0);
   #endif
 
-  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE
+  #if CFG_TUH_ENABLED
     tud_int_handler(0);
   #endif
 }
@@ -115,7 +115,7 @@ void board_init(void)
   SysTick_Config(SystemCoreClock / 1000);
 #elif CFG_TUSB_OS == OPT_OS_FREERTOS
   // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher )
-  NVIC_SetPriority(USB_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY );
+  NVIC_SetPriority(USB_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY);
 #endif
 
   Chip_GPIO_Init(LPC_GPIO);

hw/bsp/ea4357/ea4357.c

@@ -53,6 +53,18 @@
 //    {0x02, 7, 0, 7  }, // SW6
 //};
 
+#ifdef BOARD_TUD_RHPORT
+  #define PORT_SUPPORT_DEVICE(_n)  (BOARD_TUD_RHPORT == _n)
+#else
+  #define PORT_SUPPORT_DEVICE(_n)  0
+#endif
+
+#ifdef BOARD_TUH_RHPORT
+  #define PORT_SUPPORT_HOST(_n)    (BOARD_TUH_RHPORT == _n)
+#else
+  #define PORT_SUPPORT_HOST(_n)    0
+#endif
+
 /*------------------------------------------------------------------*/
 /* BOARD API
  *------------------------------------------------------------------*/
@@ -116,7 +128,7 @@ void board_init(void)
   SysTick_Config(SystemCoreClock / 1000);
 #elif CFG_TUSB_OS == OPT_OS_FREERTOS
   // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher )
-  //NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY );
+  NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY);
 #endif
 
   Chip_GPIO_Init(LPC_GPIO_PORT);
@@ -170,7 +182,7 @@ void board_init(void)
    * - Insert jumpers in position 2-3 in JP17/JP18/JP19
    * - Insert jumpers in JP31 (OTG)
    */
-#if CFG_TUSB_RHPORT0_MODE
+#if PORT_SUPPORT_DEVICE(0) || PORT_SUPPORT_HOST(0)
   Chip_USB0_Init();
 #endif
 
@@ -195,14 +207,14 @@ void board_init(void)
    * - LED34 lights green when +5V is available on J20.
    * - JP15 shall not be inserted. JP16 has no effect
    */
-#if CFG_TUSB_RHPORT1_MODE
+#if PORT_SUPPORT_DEVICE(1) || PORT_SUPPORT_HOST(1)
   Chip_USB1_Init();
 #endif
 
   // USB0 Vbus Power: P2_3 on EA4357 channel B U20 GPIO26 active low (base board)
   Chip_SCU_PinMuxSet(2, 3, SCU_MODE_PULLUP | SCU_MODE_INBUFF_EN | SCU_MODE_FUNC7);
 
-  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE
+  #if PORT_SUPPORT_DEVICE(0)
   // P9_5 (GPIO5[18]) (GPIO28 on oem base) as USB connect, active low.
   Chip_SCU_PinMuxSet(9, 5, SCU_MODE_PULLDOWN | SCU_MODE_FUNC4);
   Chip_GPIO_SetPinDIROutput(LPC_GPIO_PORT, 5, 18);
@@ -217,23 +229,23 @@ void board_init(void)
 //--------------------------------------------------------------------+
 void USB0_IRQHandler(void)
 {
-  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST
+  #if PORT_SUPPORT_DEVICE(0)
-    tuh_int_handler(0);
+    tud_int_handler(0);
   #endif
 
-  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE
+  #if PORT_SUPPORT_HOST(0)
-    tud_int_handler(0);
+    tuh_int_handler(0);
   #endif
 }
 
 void USB1_IRQHandler(void)
 {
-  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST
+  #if PORT_SUPPORT_DEVICE(1)
-    tuh_int_handler(1);
+    tud_int_handler(1);
   #endif
 
-  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE
+  #if PORT_SUPPORT_HOST(1)
-    tud_int_handler(1);
+    tuh_int_handler(1);
   #endif
 }
 

hw/bsp/fomu/fomu.c

@@ -61,7 +61,7 @@ void isr(void)
 
   irqs = irq_pending() & irq_getmask();
 
-#if CFG_TUSB_RHPORT0_MODE == OPT_MODE_DEVICE
+#if CFG_TUD_ENABLED
   if (irqs & (1 << USB_INTERRUPT)) {
     tud_int_handler(0);
   }

hw/bsp/imxrt/family.c

@@ -34,9 +34,25 @@
 
 #include "clock_config.h"
 
+#ifdef BOARD_TUD_RHPORT
+  #define PORT_SUPPORT_DEVICE(_n)  (BOARD_TUD_RHPORT == _n)
+#else
+  #define PORT_SUPPORT_DEVICE(_n)  0
+#endif
+
+#ifdef BOARD_TUH_RHPORT
+  #define PORT_SUPPORT_HOST(_n)    (BOARD_TUH_RHPORT == _n)
+#else
+  #define PORT_SUPPORT_HOST(_n)    0
+#endif
+
 // needed by fsl_flexspi_nor_boot
 const uint8_t dcd_data[] = { 0x00 };
 
+//--------------------------------------------------------------------+
+//
+//--------------------------------------------------------------------+
+
 void board_init(void)
 {
   // Init clock
@@ -51,9 +67,9 @@ void board_init(void)
   SysTick_Config(SystemCoreClock / 1000);
 #elif CFG_TUSB_OS == OPT_OS_FREERTOS
   // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher )
-  NVIC_SetPriority(USB_OTG1_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY );
+  NVIC_SetPriority(USB_OTG1_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY);
-#ifdef USB_OTG2_IRQn
+#ifdef USBPHY2
-  NVIC_SetPriority(USB_OTG2_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY );
+  NVIC_SetPriority(USB_OTG2_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY);
 #endif
 #endif
 
@@ -149,23 +165,23 @@ void board_init(void)
 //--------------------------------------------------------------------+
 void USB_OTG1_IRQHandler(void)
 {
-  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST
+  #if PORT_SUPPORT_DEVICE(0)
-    tuh_int_handler(0);
+    tud_int_handler(0);
   #endif
 
-  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE
+  #if PORT_SUPPORT_HOST(0)
-    tud_int_handler(0);
+    tuh_int_handler(0);
   #endif
 }
 
 void USB_OTG2_IRQHandler(void)
 {
-  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST
+  #if PORT_SUPPORT_DEVICE(1)
-    tuh_int_handler(1);
+    tud_int_handler(1);
   #endif
 
-  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE
+  #if PORT_SUPPORT_HOST(1)
-    tud_int_handler(1);
+    tuh_int_handler(1);
   #endif
 }
 

hw/bsp/lpc54/family.c

@@ -33,6 +33,18 @@
 #include "bsp/board.h"
 #include "board.h"
 
+#ifdef BOARD_TUD_RHPORT
+  #define PORT_SUPPORT_DEVICE(_n)  (BOARD_TUD_RHPORT == _n)
+#else
+  #define PORT_SUPPORT_DEVICE(_n)  0
+#endif
+
+#ifdef BOARD_TUH_RHPORT
+  #define PORT_SUPPORT_HOST(_n)    (BOARD_TUH_RHPORT == _n)
+#else
+  #define PORT_SUPPORT_HOST(_n)    0
+#endif
+
 //--------------------------------------------------------------------+
 // MACRO TYPEDEF CONSTANT ENUM
 //--------------------------------------------------------------------+
@@ -152,8 +164,7 @@ void board_init(void)
 
 #if defined(FSL_FEATURE_SOC_USBHSD_COUNT) && FSL_FEATURE_SOC_USBHSD_COUNT
   // LPC546xx and LPC540xx has OTG 1 FS + 1 HS rhports
-
+  #if PORT_SUPPORT_DEVICE(0)
-  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE
     // Port0 is Full Speed
     POWER_DisablePD(kPDRUNCFG_PD_USB0_PHY); /*< Turn on USB Phy */
     CLOCK_SetClkDiv(kCLOCK_DivUsb0Clk, 1, false);
@@ -167,7 +178,7 @@ void board_init(void)
     CLOCK_EnableUsbfs0DeviceClock(kCLOCK_UsbSrcFro, CLOCK_GetFroHfFreq());
   #endif
 
-  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE
+  #if PORT_SUPPORT_DEVICE(1)
     // Port1 is High Speed
     POWER_DisablePD(kPDRUNCFG_PD_USB1_PHY);
 
@@ -178,10 +189,8 @@ void board_init(void)
 
     CLOCK_EnableUsbhs0DeviceClock(kCLOCK_UsbSrcUsbPll, 0U);
   #endif
-
 #else
   // LPC5411x series only has full speed device
-
   POWER_DisablePD(kPDRUNCFG_PD_USB0_PHY); // Turn on USB Phy
   CLOCK_EnableUsbfs0Clock(kCLOCK_UsbSrcFro, CLOCK_GetFreq(kCLOCK_FroHf)); /* enable USB IP clock */
 #endif

hw/bsp/lpc55/family.c

@@ -34,6 +34,18 @@
 #include "fsl_sctimer.h"
 #include "sct_neopixel.h"
 
+#ifdef BOARD_TUD_RHPORT
+  #define PORT_SUPPORT_DEVICE(_n)  (BOARD_TUD_RHPORT == _n)
+#else
+  #define PORT_SUPPORT_DEVICE(_n)  0
+#endif
+
+#ifdef BOARD_TUH_RHPORT
+  #define PORT_SUPPORT_HOST(_n)    (BOARD_TUH_RHPORT == _n)
+#else
+  #define PORT_SUPPORT_HOST(_n)    0
+#endif
+
 //--------------------------------------------------------------------+
 // MACRO TYPEDEF CONSTANT ENUM
 //--------------------------------------------------------------------+
@@ -164,7 +176,7 @@ void board_init(void)
   /* PORT0 PIN22 configured as USB0_VBUS */
   IOCON_PinMuxSet(IOCON, 0U, 22U, IOCON_PIO_DIG_FUNC7_EN);
 
-#if CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE
+#if PORT_SUPPORT_DEVICE(0)
   // Port0 is Full Speed
 
   /* Turn on USB0 Phy */
@@ -189,7 +201,7 @@ void board_init(void)
   CLOCK_EnableUsbfs0DeviceClock(kCLOCK_UsbfsSrcFro, CLOCK_GetFreq(kCLOCK_FroHf));
 #endif
 
-#if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE
+#if PORT_SUPPORT_DEVICE(1)
   // Port1 is High Speed
 
   /* Turn on USB1 Phy */

hw/bsp/lpcxpresso1769/lpcxpresso1769.c

@@ -32,12 +32,12 @@
 //--------------------------------------------------------------------+
 void USB_IRQHandler(void)
 {
-  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST
+  #if CFG_TUD_ENABLED
-    tuh_int_handler(0);
+    tud_int_handler(0);
   #endif
 
-  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE
+  #if CFG_TUH_ENABLED
-    tud_int_handler(0);
+    tuh_int_handler(0);
   #endif
 }
 

hw/bsp/mbed1768/mbed1768.c

@@ -146,12 +146,12 @@ void board_init(void)
 //--------------------------------------------------------------------+
 void USB_IRQHandler(void)
 {
-  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST
+  #if CFG_TUD_ENABLED
-    tuh_int_handler(0);
+    tud_int_handler(0);
   #endif
 
-  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE
+  #if CFG_TUH_ENABLED
-    tud_int_handler(0);
+    tuh_int_handler(0);
   #endif
 }
 

hw/bsp/ngx4330/ngx4330.c

@@ -40,6 +40,18 @@
 #define BOARD_UART_PIN_TX         10 // PF.10 : UART0_TXD
 #define BOARD_UART_PIN_RX         11 // PF.11 : UART0_RXD
 
+#ifdef BOARD_TUD_RHPORT
+  #define PORT_SUPPORT_DEVICE(_n)  (BOARD_TUD_RHPORT == _n)
+#else
+  #define PORT_SUPPORT_DEVICE(_n)  0
+#endif
+
+#ifdef BOARD_TUH_RHPORT
+  #define PORT_SUPPORT_HOST(_n)    (BOARD_TUH_RHPORT == _n)
+#else
+  #define PORT_SUPPORT_HOST(_n)    0
+#endif
+
 /*------------------------------------------------------------------*/
 /* BOARD API
  *------------------------------------------------------------------*/
@@ -120,7 +132,7 @@ void board_init(void)
   SysTick_Config(SystemCoreClock / 1000);
 #elif CFG_TUSB_OS == OPT_OS_FREERTOS
   // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher )
-  //NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY );
+  NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY);
 #endif
 
   Chip_GPIO_Init(LPC_GPIO_PORT);
@@ -167,9 +179,7 @@ void board_init(void)
    * status feedback from the distribution switch. GPIO54 is used for VBUS sensing. 15Kohm pull-down
    * resistors are always active
    */
-#if CFG_TUSB_RHPORT0_MODE
   Chip_USB0_Init();
-#endif
 
   /* USB1
    * When USB channel #1 is used as USB Host, 15Kohm pull-down resistors are needed on the USB data
@@ -189,12 +199,9 @@ void board_init(void)
    * of VBUS can be read via U31.
    * JP16 shall not be inserted.
    */
-#if CFG_TUSB_RHPORT1_MODE
   Chip_USB1_Init();
-
 //	Chip_GPIO_SetPinDIROutput(LPC_GPIO_PORT, 5, 6);							/* GPIO5[6] = USB1_PWR_EN */
 //	Chip_GPIO_SetPinState(LPC_GPIO_PORT, 5, 6, true);							/* GPIO5[6] output high */
-#endif
 }
 
 //--------------------------------------------------------------------+
@@ -202,23 +209,23 @@ void board_init(void)
 //--------------------------------------------------------------------+
 void USB0_IRQHandler(void)
 {
-  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST
+  #if PORT_SUPPORT_DEVICE(0)
-    tuh_int_handler(0);
+    tud_int_handler(0);
   #endif
 
-  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE
+  #if PORT_SUPPORT_HOST(0)
-    tud_int_handler(0);
+    tuh_int_handler(0);
   #endif
 }
 
 void USB1_IRQHandler(void)
 {
-  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST
+  #if PORT_SUPPORT_DEVICE(1)
-    tuh_int_handler(1);
+    tud_int_handler(1);
   #endif
 
-  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE
+  #if PORT_SUPPORT_HOST(1)
-    tud_int_handler(1);
+    tuh_int_handler(1);
   #endif
 }
 

hw/bsp/samg55xplained/samg55xplained.c

@@ -99,7 +99,7 @@ void board_init(void)
 //--------------------------------------------------------------------+
 void UDP_Handler(void)
 {
-  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE
+  #if CFG_TUD_ENABLED
     tud_int_handler(0);
   #endif
 }

src/portable/bridgetek/ft9xx/dcd_ft9xx.c

@@ -312,7 +312,7 @@ static void _dcd_ft90x_detach(void)
 
 // Determine the speed of the USB to which we are connected.
 // Set the speed of the PHY accordingly. 
-// High speed can be disabled through CFG_TUSB_RHPORT0_MODE settings.
+// High speed can be disabled through CFG_TUSB_RHPORT0_MODE or CFG_TUD_MAX_SPEED settings.
 static void _ft90x_usb_speed(void)
 {
 	uint8_t  fctrl_val;