adding lpc54xxx to dcd, able to go through enumeration
This commit is contained in:
parent
403662a1d6
commit
3067809957
|
@ -114,18 +114,18 @@ void board_init(void)
|
||||||
GPIO_PinInit(GPIO, BUTTON_PORT, BUTTON_PIN, &button_config);
|
GPIO_PinInit(GPIO, BUTTON_PORT, BUTTON_PIN, &button_config);
|
||||||
|
|
||||||
// USB
|
// USB
|
||||||
// const uint32_t port1_pin6_config = (
|
const uint32_t port1_pin6_config = (
|
||||||
// IOCON_PIO_FUNC7 | /* Pin is configured as USB0_VBUS */
|
IOCON_PIO_FUNC7 | /* Pin is configured as USB0_VBUS */
|
||||||
// IOCON_PIO_MODE_INACT | /* No addition pin function */
|
IOCON_PIO_MODE_INACT | /* No addition pin function */
|
||||||
// IOCON_PIO_INV_DI | /* Input function is not inverted */
|
IOCON_PIO_INV_DI | /* Input function is not inverted */
|
||||||
// IOCON_PIO_DIGITAL_EN | /* Enables digital function */
|
IOCON_PIO_DIGITAL_EN | /* Enables digital function */
|
||||||
// IOCON_PIO_INPFILT_OFF | /* Input filter disabled */
|
IOCON_PIO_INPFILT_OFF | /* Input filter disabled */
|
||||||
// IOCON_PIO_OPENDRAIN_DI /* Open drain is disabled */
|
IOCON_PIO_OPENDRAIN_DI /* Open drain is disabled */
|
||||||
// );
|
);
|
||||||
// IOCON_PinMuxSet(IOCON, 1, 6, port1_pin6_config); /* PORT1 PIN6 (coords: 26) is configured as USB0_VBUS */
|
IOCON_PinMuxSet(IOCON, 1, 6, port1_pin6_config); /* PORT1 PIN6 (coords: 26) is configured as USB0_VBUS */
|
||||||
//
|
|
||||||
// POWER_DisablePD(kPDRUNCFG_PD_USB0_PHY); /*Turn on USB Phy */
|
POWER_DisablePD(kPDRUNCFG_PD_USB0_PHY); /*Turn on USB Phy */
|
||||||
// CLOCK_EnableUsbfs0Clock(kCLOCK_UsbSrcFro, CLOCK_GetFreq(kCLOCK_FroHf)); /* enable USB IP clock */
|
CLOCK_EnableUsbfs0Clock(kCLOCK_UsbSrcFro, CLOCK_GetFreq(kCLOCK_FroHf)); /* enable USB IP clock */
|
||||||
}
|
}
|
||||||
|
|
||||||
//--------------------------------------------------------------------+
|
//--------------------------------------------------------------------+
|
||||||
|
|
|
@ -38,14 +38,15 @@
|
||||||
|
|
||||||
#if TUSB_OPT_DEVICE_ENABLED && ( CFG_TUSB_MCU == OPT_MCU_LPC11UXX || \
|
#if TUSB_OPT_DEVICE_ENABLED && ( CFG_TUSB_MCU == OPT_MCU_LPC11UXX || \
|
||||||
CFG_TUSB_MCU == OPT_MCU_LPC13XX || \
|
CFG_TUSB_MCU == OPT_MCU_LPC13XX || \
|
||||||
CFG_TUSB_MCU == OPT_MCU_LPC51UXX )
|
CFG_TUSB_MCU == OPT_MCU_LPC51UXX || \
|
||||||
|
CFG_TUSB_MCU == OPT_MCU_LPC54XXX )
|
||||||
|
|
||||||
#if CFG_TUSB_MCU == OPT_MCU_LPC11UXX || CFG_TUSB_MCU == OPT_MCU_LPC13XX
|
#if CFG_TUSB_MCU == OPT_MCU_LPC11UXX || CFG_TUSB_MCU == OPT_MCU_LPC13XX
|
||||||
// LPC11Uxx and LPC13xx use lpcopen
|
// LPC11Uxx and LPC13xx use lpcopen
|
||||||
#include "chip.h"
|
#include "chip.h"
|
||||||
#define DCD_REGS LPC_USB
|
#define DCD_REGS LPC_USB
|
||||||
#define DCD_IRQHandler USB_IRQHandler
|
#define DCD_IRQHandler USB_IRQHandler
|
||||||
#elif CFG_TUSB_MCU == OPT_MCU_LPC51UXX
|
#elif CFG_TUSB_MCU == OPT_MCU_LPC51UXX || CFG_TUSB_MCU == OPT_MCU_LPC54XXX
|
||||||
#include "fsl_device_registers.h"
|
#include "fsl_device_registers.h"
|
||||||
#define DCD_REGS USB0
|
#define DCD_REGS USB0
|
||||||
#define DCD_IRQHandler USB0_IRQHandler
|
#define DCD_IRQHandler USB0_IRQHandler
|
||||||
|
@ -60,7 +61,8 @@
|
||||||
// Number of endpoints
|
// Number of endpoints
|
||||||
#define EP_COUNT 10
|
#define EP_COUNT 10
|
||||||
|
|
||||||
// only SRAM1 & USB RAM can be used for transfer
|
// only SRAM1 & USB RAM can be used for transfer.
|
||||||
|
// Used to set DATABUFSTART which is 22-bit aligned
|
||||||
// 2000 0000 to 203F FFFF
|
// 2000 0000 to 203F FFFF
|
||||||
#define SRAM_REGION 0x20000000
|
#define SRAM_REGION 0x20000000
|
||||||
|
|
||||||
|
|
Loading…
Reference in New Issue