application: add multiplexer control
This commit is contained in:
parent
0b0a27e670
commit
468f199d22
|
@ -59,6 +59,12 @@ const uint8_t channels[] = {ADC_CHANNEL17, ADC_CHANNEL(TARGET_CHANNEL), ADC_CHAN
|
|||
#define SIGNAL_PU_PIN PA4 /**< pin to pull signal to target voltage (controlling gate of pMOS) */
|
||||
#define TARGET_EN PA5 /**< pin to provide target voltage to LV side of voltage shifter (pulling them high through 10 kO) */
|
||||
|
||||
#define MUX_EN_PIN PB2 /**< pin to enable analog multiplexer (active low) */
|
||||
#define MUX_S0_PIN PA6 /**< pin to set S0 bit of analog multiplexer */
|
||||
#define MUX_S1_PIN PA7 /**< pin to set S1 bit of analog multiplexer */
|
||||
#define MUX_S2_PIN PB0 /**< pin to set S2 bit of analog multiplexer */
|
||||
#define MUX_S3_PIN PB1 /**< pin to set S3 bit of analog multiplexer */
|
||||
|
||||
size_t putc(char c)
|
||||
{
|
||||
size_t length = 0; // number of characters printed
|
||||
|
@ -118,6 +124,39 @@ static float* measure_voltages(void)
|
|||
return voltages;
|
||||
}
|
||||
|
||||
/** select channel of multiplexer
|
||||
* @param[in] channel channel to select, or -1 to disable multiplexer
|
||||
*/
|
||||
static void mux_select(int8_t channel)
|
||||
{
|
||||
gpio_set(GPIO_PORT(MUX_EN_PIN), GPIO_PIN(MUX_EN_PIN)); // disable multiplexer while we are switching
|
||||
if (channel < 0 || channel > 15) {
|
||||
return; // no channel to select
|
||||
}
|
||||
// select channel using bit pattern
|
||||
if (channel & 0x1) {
|
||||
gpio_set(GPIO_PORT(MUX_S0_PIN), GPIO_PIN(MUX_S0_PIN));
|
||||
} else {
|
||||
gpio_clear(GPIO_PORT(MUX_S0_PIN), GPIO_PIN(MUX_S0_PIN));
|
||||
}
|
||||
if (channel & 0x2) {
|
||||
gpio_set(GPIO_PORT(MUX_S1_PIN), GPIO_PIN(MUX_S1_PIN));
|
||||
} else {
|
||||
gpio_clear(GPIO_PORT(MUX_S1_PIN), GPIO_PIN(MUX_S1_PIN));
|
||||
}
|
||||
if (channel & 0x4) {
|
||||
gpio_set(GPIO_PORT(MUX_S2_PIN), GPIO_PIN(MUX_S2_PIN));
|
||||
} else {
|
||||
gpio_clear(GPIO_PORT(MUX_S2_PIN), GPIO_PIN(MUX_S2_PIN));
|
||||
}
|
||||
if (channel & 0x8) {
|
||||
gpio_set(GPIO_PORT(MUX_S3_PIN), GPIO_PIN(MUX_S3_PIN));
|
||||
} else {
|
||||
gpio_clear(GPIO_PORT(MUX_S3_PIN), GPIO_PIN(MUX_S3_PIN));
|
||||
}
|
||||
gpio_clear(GPIO_PORT(MUX_EN_PIN), GPIO_PIN(MUX_EN_PIN)); // enable multiplexer
|
||||
}
|
||||
|
||||
// menu commands
|
||||
|
||||
static void command_swd_scan(void* argument)
|
||||
|
@ -578,6 +617,30 @@ void main(void)
|
|||
gpio_mode_setup(GPIO_PORT(SIGNAL_PU_PIN), GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, GPIO_PIN(SIGNAL_PU_PIN)); // configure pin as output
|
||||
puts("OK\n");
|
||||
|
||||
puts("setup analog multiplexer: ");
|
||||
rcc_periph_clock_enable(GPIO_RCC(MUX_EN_PIN)); // enable clock for port domain
|
||||
gpio_set(GPIO_PORT(MUX_EN_PIN), GPIO_PIN(MUX_EN_PIN)); // ensure multiplexer is disabled
|
||||
gpio_set_output_options(GPIO_PORT(MUX_EN_PIN), GPIO_OTYPE_PP, GPIO_OSPEED_2MHZ, GPIO_PIN(MUX_EN_PIN)); // set output as push-pull to drive correctly
|
||||
gpio_mode_setup(GPIO_PORT(MUX_EN_PIN), GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, GPIO_PIN(MUX_EN_PIN)); // configure pin as output
|
||||
rcc_periph_clock_enable(GPIO_RCC(MUX_S0_PIN)); // enable clock for port domain
|
||||
gpio_clear(GPIO_PORT(MUX_S0_PIN), GPIO_PIN(MUX_S0_PIN)); // any channel selected is fine
|
||||
gpio_set_output_options(GPIO_PORT(MUX_S0_PIN), GPIO_OTYPE_PP, GPIO_OSPEED_2MHZ, GPIO_PIN(MUX_S0_PIN)); // set output as push-pull to drive correctly
|
||||
gpio_mode_setup(GPIO_PORT(MUX_S0_PIN), GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, GPIO_PIN(MUX_S0_PIN)); // configure pin as output
|
||||
rcc_periph_clock_enable(GPIO_RCC(MUX_S1_PIN)); // enable clock for port domain
|
||||
gpio_clear(GPIO_PORT(MUX_S1_PIN), GPIO_PIN(MUX_S1_PIN)); // any channel selected is fine
|
||||
gpio_set_output_options(GPIO_PORT(MUX_S1_PIN), GPIO_OTYPE_PP, GPIO_OSPEED_2MHZ, GPIO_PIN(MUX_S1_PIN)); // set output as push-pull to drive correctly
|
||||
gpio_mode_setup(GPIO_PORT(MUX_S1_PIN), GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, GPIO_PIN(MUX_S1_PIN)); // configure pin as output
|
||||
rcc_periph_clock_enable(GPIO_RCC(MUX_S2_PIN)); // enable clock for port domain
|
||||
gpio_clear(GPIO_PORT(MUX_S2_PIN), GPIO_PIN(MUX_S2_PIN)); // any channel selected is fine
|
||||
gpio_set_output_options(GPIO_PORT(MUX_S2_PIN), GPIO_OTYPE_PP, GPIO_OSPEED_2MHZ, GPIO_PIN(MUX_S2_PIN)); // set output as push-pull to drive correctly
|
||||
gpio_mode_setup(GPIO_PORT(MUX_S2_PIN), GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, GPIO_PIN(MUX_S2_PIN)); // configure pin as output
|
||||
rcc_periph_clock_enable(GPIO_RCC(MUX_S3_PIN)); // enable clock for port domain
|
||||
gpio_clear(GPIO_PORT(MUX_S3_PIN), GPIO_PIN(MUX_S3_PIN)); // any channel selected is fine
|
||||
gpio_set_output_options(GPIO_PORT(MUX_S3_PIN), GPIO_OTYPE_PP, GPIO_OSPEED_2MHZ, GPIO_PIN(MUX_S3_PIN)); // set output as push-pull to drive correctly
|
||||
gpio_mode_setup(GPIO_PORT(MUX_S3_PIN), GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, GPIO_PIN(MUX_S3_PIN)); // configure pin as output
|
||||
mux_select(-1); // ensure it is disabled
|
||||
puts("OK\n");
|
||||
|
||||
puts("setup ADC to measure voltages: ");
|
||||
rcc_periph_clock_enable(RCC_ADC1); // enable clock for ADC domain
|
||||
adc_power_off(ADC1); // switch off ADC while configuring it
|
||||
|
|
Loading…
Reference in New Issue