61 lines
2.2 KiB
Makefile
61 lines
2.2 KiB
Makefile
DEPS_SUBMODULES += hw/mcu/nuvoton
|
|
|
|
CFLAGS += \
|
|
-flto \
|
|
-mthumb \
|
|
-mabi=aapcs-linux \
|
|
-mcpu=cortex-m4 \
|
|
-mfloat-abi=hard \
|
|
-mfpu=fpv4-sp-d16 \
|
|
-DCFG_TUSB_MCU=OPT_MCU_NUC505
|
|
|
|
# All source paths should be relative to the top level.
|
|
LD_FILE = hw/bsp/$(BOARD)/nuc505_flashtoram.ld
|
|
|
|
SRC_C += \
|
|
src/portable/nuvoton/nuc505/dcd_nuc505.c \
|
|
hw/mcu/nuvoton/nuc505/Device/Nuvoton/NUC505Series/Source/system_NUC505Series.c \
|
|
hw/mcu/nuvoton/nuc505/StdDriver/src/adc.c \
|
|
hw/mcu/nuvoton/nuc505/StdDriver/src/clk.c \
|
|
hw/mcu/nuvoton/nuc505/StdDriver/src/gpio.c \
|
|
hw/mcu/nuvoton/nuc505/StdDriver/src/i2c.c \
|
|
hw/mcu/nuvoton/nuc505/StdDriver/src/i2s.c \
|
|
hw/mcu/nuvoton/nuc505/StdDriver/src/pwm.c \
|
|
hw/mcu/nuvoton/nuc505/StdDriver/src/rtc.c \
|
|
hw/mcu/nuvoton/nuc505/StdDriver/src/spi.c \
|
|
hw/mcu/nuvoton/nuc505/StdDriver/src/spim.c \
|
|
hw/mcu/nuvoton/nuc505/StdDriver/src/sys.c \
|
|
hw/mcu/nuvoton/nuc505/StdDriver/src/timer.c \
|
|
hw/mcu/nuvoton/nuc505/StdDriver/src/uart.c \
|
|
hw/mcu/nuvoton/nuc505/StdDriver/src/wdt.c \
|
|
hw/mcu/nuvoton/nuc505/StdDriver/src/wwdt.c
|
|
|
|
SRC_S += \
|
|
hw/mcu/nuvoton/nuc505/Device/Nuvoton/NUC505Series/Source/GCC/startup_NUC505Series.S
|
|
|
|
INC += \
|
|
$(TOP)/hw/mcu/nuvoton/nuc505/Device/Nuvoton/NUC505Series/Include \
|
|
$(TOP)/hw/mcu/nuvoton/nuc505/StdDriver/inc \
|
|
$(TOP)/hw/mcu/nuvoton/nuc505/CMSIS/Include
|
|
|
|
# For freeRTOS port source
|
|
FREERTOS_PORT = ARM_CM4F
|
|
|
|
# For flash-jlink target
|
|
JLINK_DEVICE = NUC505YO13Y
|
|
|
|
# Note
|
|
# To be able to program the SPI flash, it need to boot with ICP mode "1011".
|
|
# However, in ICP mode, opencod cannot establish connection to the mcu.
|
|
# Therefore, there is no easy command line flash for NUC505
|
|
# It is probably better to just use Nuvoton NuMicro ICP programming on windows to program the board
|
|
# - 1111 "SPI" (run from internal flash)
|
|
# - 1110 "USB" (mass storage emulator that accepts a .bin file)
|
|
# - 0111 "ICE-SPI" (allow external debugger access, but may not be programmable)
|
|
# - 1011 ICP mode (programmable via NuMicro ICP programming tool)
|
|
|
|
# Flash using Nuvoton's openocd fork at https://github.com/OpenNuvoton/OpenOCD-Nuvoton
|
|
# Please compile and install it from github source
|
|
flash: $(BUILD)/$(PROJECT).elf
|
|
openocd -f interface/nulink.cfg -f target/numicroM4.cfg -c "program $< reset exit"
|