add USB-Blaster board support
This commit is contained in:
parent
60837a7539
commit
3242c6ba5c
|
|
@ -25,6 +25,7 @@ The underlying template also supports following board:
|
|||
- [blue pill](ihttps://wiki.cuvoodoo.info/doku.php?id=stm32f1xx#blue_pill), based on a STM32F103C8T6
|
||||
- [core board](https://wiki.cuvoodoo.info/doku.php?id=stm32f1xx#core_board), based on a STM32F103C8T6
|
||||
- [ST-LINK V2 mini](https://wiki.cuvoodoo.info/doku.php?id=jtag#mini_st-link_v2), a ST-LINK/V2 clone based on a STM32F101C8T6
|
||||
- [USB-Blaster](https://wiki.cuvoodoo.info/doku.php?id=jtag#armjishu_usb-blaster), an Altera USB-Blaster clone based on a STM32F101C8T6
|
||||
|
||||
**Which board is used is defined in the Makefile**.
|
||||
This is required to map the user LED and button provided on the board
|
||||
|
|
@ -33,6 +34,13 @@ The ST-LINK V2 mini clone has SWD test points on the board.
|
|||
Because read protection is enabled, you will first need to remove the protection to be able to flash the firmware.
|
||||
To remove the read protection (and erase flash), run `rake remove_protection` while a SWD adapter is connected.
|
||||
|
||||
The Altera USB-Blaster clone has a pin header for SWD and UART1 on the board.
|
||||
SWD is disabled in the main firmware, and it has read protection.
|
||||
To be able to flash using SWD (or the serial port), the BOOT0 pin must be set to 1 to boot the system memory install of the flash memory.
|
||||
To set BOOT0 to 1, apply 3.3 V on R11, between the resistor and the reference designator, when powering the device.
|
||||
The red LED should stay off while the green LED is on.
|
||||
Now you can remove the read protection (and erase flash), run `rake remove_protection` while a SWD adapter is connected.
|
||||
|
||||
connections
|
||||
===========
|
||||
|
||||
|
|
|
|||
2
Rakefile
2
Rakefile
|
|
@ -14,7 +14,7 @@ APPLICATION = "application"
|
|||
FIRMWARES = [BOOTLOADER, APPLICATION]
|
||||
|
||||
# which development board is used
|
||||
# supported are: SYSTEM_BOARD, MAPLE_MINI, BLUE_PILL, CORE_BOARD, STLINKV2, BUSVOODOO
|
||||
# supported are: SYSTEM_BOARD, MAPLE_MINI, BLUE_PILL, CORE_BOARD, STLINKV2, BLASTER, BUSVOODOO
|
||||
BOARD = ENV["BOARD"] || "CORE_BOARD"
|
||||
|
||||
# libopencm3 definitions
|
||||
|
|
|
|||
|
|
@ -372,7 +372,7 @@ void main(void)
|
|||
|
||||
// setup RTC
|
||||
printf("setup internal RTC: ");
|
||||
#if defined(BLUE_PILL) || defined(STLINKV2) // for boards without a Low Speed External oscillator
|
||||
#if defined(BLUE_PILL) || defined(STLINKV2) || defined(BLASTER) // for boards without a Low Speed External oscillator
|
||||
// note: the blue pill LSE oscillator is affected when toggling the onboard LED, thus prefer the HSE
|
||||
rtc_auto_awake(RCC_HSE, 8000000 / 128 - 1); // use High Speed External oscillator (8 MHz / 128) as RTC clock (VBAT can't be used to keep the RTC running)
|
||||
#else // for boards with an precise Low Speed External oscillator
|
||||
|
|
|
|||
9
global.h
9
global.h
|
|
@ -622,10 +622,14 @@
|
|||
/* on maple mini LED is on pin 19/PB1 */
|
||||
#define LED_PIN PB1 /**< GPIO pin (pin PB1 on maple mini) */
|
||||
#define LED_ON 1 /**< LED is on when pin is high */
|
||||
#elif defined (STLINKV2) // it's actually a STM32F101, but it seems to have all STM32F103 features
|
||||
#elif defined (STLINKV2) // it's sometimes a STM32F101, but it seems to have all STM32F103 features
|
||||
/* on ST-Link V2 clone dongle in aluminum case LED is on pin PA9 (remap USART1_TX if used) */
|
||||
#define LED_PIN PA9 /**< GPIO pin (pin PA9) */
|
||||
#define LED_ON 1 /**< the color and on level depends on the clone */
|
||||
#elif defined (BLASTER)
|
||||
/* on Altera USB blaster clone LED is on pin PA5 */
|
||||
#define LED_PIN PA5 /**< GPIO pin (pin PA5) */
|
||||
#define LED_ON 0 /**< red LED on when low (green LED is on when device is powered) */
|
||||
#elif defined (BUSVOODOO)
|
||||
/* on BusVoodoo LED is on pin PA8 */
|
||||
#define LED_PIN PA8 /**< GPIO pin (pin PA8) */
|
||||
|
|
@ -658,6 +662,9 @@
|
|||
/* use button */
|
||||
#define DFU_FORCE_PIN BUTTON_PIN /**< button pin */
|
||||
#define DFU_FORCE_VALUE BUTTON_PRESSED /**< button floating unpressed, connected to ground pressed to force DFU mode */
|
||||
#elif defined (BLASTER)
|
||||
#define DFU_FORCE_PIN PA8 /**< GPIO pin (pin PA8, not SWD and UART pin on debug port) */
|
||||
#define DFU_FORCE_VALUE 0 /**< short to nearby ground connection to force DFU */
|
||||
#elif defined(BUSVOODOO)
|
||||
#if BUSVOODOO_HARDWARE_VERSION==0
|
||||
/* on BusVoodoo v0 DFU input is on PC7 */
|
||||
|
|
|
|||
|
|
@ -258,6 +258,11 @@ static void usb_disconnect(void)
|
|||
rcc_periph_clock_enable(RCC_GPIOB);
|
||||
gpio_set_mode(GPIOB, GPIO_MODE_OUTPUT_2_MHZ, GPIO_CNF_OUTPUT_PUSHPULL, GPIO9);
|
||||
gpio_set(GPIOB, GPIO9);
|
||||
#elif defined(BLASTER)
|
||||
// enable USB D+ pull-up
|
||||
rcc_periph_clock_enable(RCC_GPIOB);
|
||||
gpio_set_mode(GPIOB, GPIO_MODE_OUTPUT_2_MHZ, GPIO_CNF_OUTPUT_PUSHPULL, GPIO6);
|
||||
gpio_set(GPIOB, GPIO6);
|
||||
#endif
|
||||
// pull USB D+ low for a short while
|
||||
rcc_periph_clock_enable(RCC_GPIOA);
|
||||
|
|
@ -446,6 +451,11 @@ void usb_cdcacm_setup(void)
|
|||
rcc_periph_clock_enable(RCC_GPIOB);
|
||||
gpio_set_mode(GPIOB, GPIO_MODE_OUTPUT_2_MHZ, GPIO_CNF_OUTPUT_PUSHPULL, GPIO9);
|
||||
gpio_clear(GPIOB, GPIO9);
|
||||
#elif defined(BLASTER)
|
||||
// enable USB D+ pull-up using GPIO
|
||||
rcc_periph_clock_enable(RCC_GPIOB);
|
||||
gpio_set_mode(GPIOB, GPIO_MODE_OUTPUT_2_MHZ, GPIO_CNF_OUTPUT_PUSHPULL, GPIO6);
|
||||
gpio_set(GPIOB, GPIO6);
|
||||
#endif
|
||||
rcc_periph_clock_enable(RCC_GPIOA); // enable clock for GPIO used for USB
|
||||
rcc_periph_clock_enable(RCC_USB); // enable clock for USB domain
|
||||
|
|
|
|||
|
|
@ -139,6 +139,11 @@ static void usb_disconnect(void)
|
|||
rcc_periph_clock_enable(RCC_GPIOB);
|
||||
gpio_set_mode(GPIOB, GPIO_MODE_OUTPUT_2_MHZ, GPIO_CNF_OUTPUT_PUSHPULL, GPIO9);
|
||||
gpio_set(GPIOB, GPIO9);
|
||||
#elif defined(BLASTER)
|
||||
// enable USB D+ pull-up
|
||||
rcc_periph_clock_enable(RCC_GPIOB);
|
||||
gpio_set_mode(GPIOB, GPIO_MODE_OUTPUT_2_MHZ, GPIO_CNF_OUTPUT_PUSHPULL, GPIO6);
|
||||
gpio_set(GPIOB, GPIO6);
|
||||
#endif
|
||||
// pull USB D+ low for a short while
|
||||
rcc_periph_clock_enable(RCC_GPIOA);
|
||||
|
|
@ -312,6 +317,11 @@ void usb_dfu_setup(void)
|
|||
rcc_periph_clock_enable(RCC_GPIOB);
|
||||
gpio_set_mode(GPIOB, GPIO_MODE_OUTPUT_2_MHZ, GPIO_CNF_OUTPUT_PUSHPULL, GPIO9);
|
||||
gpio_clear(GPIOB, GPIO9);
|
||||
#elif defined(BLASTER)
|
||||
// enable USB D+ pull-up using GPIO
|
||||
rcc_periph_clock_enable(RCC_GPIOB);
|
||||
gpio_set_mode(GPIOB, GPIO_MODE_OUTPUT_2_MHZ, GPIO_CNF_OUTPUT_PUSHPULL, GPIO6);
|
||||
gpio_set(GPIOB, GPIO6);
|
||||
#endif
|
||||
rcc_periph_clock_enable(RCC_GPIOA); // enable clock for GPIO used for USB
|
||||
rcc_periph_clock_enable(RCC_USB); // enable clock for USB domain
|
||||
|
|
|
|||
Loading…
Reference in New Issue