From 00e66cf2e0bdb5221586f640dc25d26168ee1daf Mon Sep 17 00:00:00 2001 From: hathach Date: Sun, 29 Aug 2021 21:26:47 +0700 Subject: [PATCH] remove old openh743i, explicitly disable systick when using freertos for H7 --- .../STM32H743IITX_FLASH.ld | 0 .../board.h | 0 .../board.mk | 0 hw/bsp/stm32h7/family.c | 3 + .../STM32H743IITX_FLASH.ld | 175 ------- hw/bsp/waveshare_openh743i/board.c | 495 ------------------ hw/bsp/waveshare_openh743i/board.mk | 64 --- .../waveshare_openh743i/stm32h7xx_hal_conf.h | 483 ----------------- 8 files changed, 3 insertions(+), 1217 deletions(-) rename hw/bsp/stm32h7/boards/{waveshare_openh743i_2 => waveshare_openh743i}/STM32H743IITX_FLASH.ld (100%) rename hw/bsp/stm32h7/boards/{waveshare_openh743i_2 => waveshare_openh743i}/board.h (100%) rename hw/bsp/stm32h7/boards/{waveshare_openh743i_2 => waveshare_openh743i}/board.mk (100%) delete mode 100644 hw/bsp/waveshare_openh743i/STM32H743IITX_FLASH.ld delete mode 100644 hw/bsp/waveshare_openh743i/board.c delete mode 100644 hw/bsp/waveshare_openh743i/board.mk delete mode 100644 hw/bsp/waveshare_openh743i/stm32h7xx_hal_conf.h diff --git a/hw/bsp/stm32h7/boards/waveshare_openh743i_2/STM32H743IITX_FLASH.ld b/hw/bsp/stm32h7/boards/waveshare_openh743i/STM32H743IITX_FLASH.ld similarity index 100% rename from hw/bsp/stm32h7/boards/waveshare_openh743i_2/STM32H743IITX_FLASH.ld rename to hw/bsp/stm32h7/boards/waveshare_openh743i/STM32H743IITX_FLASH.ld diff --git a/hw/bsp/stm32h7/boards/waveshare_openh743i_2/board.h b/hw/bsp/stm32h7/boards/waveshare_openh743i/board.h similarity index 100% rename from hw/bsp/stm32h7/boards/waveshare_openh743i_2/board.h rename to hw/bsp/stm32h7/boards/waveshare_openh743i/board.h diff --git a/hw/bsp/stm32h7/boards/waveshare_openh743i_2/board.mk b/hw/bsp/stm32h7/boards/waveshare_openh743i/board.mk similarity index 100% rename from hw/bsp/stm32h7/boards/waveshare_openh743i_2/board.mk rename to hw/bsp/stm32h7/boards/waveshare_openh743i/board.mk diff --git a/hw/bsp/stm32h7/family.c b/hw/bsp/stm32h7/family.c index 3e1ed9e8..ba3c3e95 100644 --- a/hw/bsp/stm32h7/family.c +++ b/hw/bsp/stm32h7/family.c @@ -80,6 +80,9 @@ void board_init(void) SysTick_Config(SystemCoreClock / 1000); #elif CFG_TUSB_OS == OPT_OS_FREERTOS + // Explicitly disable systick to prevent it is trigger before scheduler start + SysTick->CTRL &= ~1U; + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) NVIC_SetPriority(OTG_FS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); NVIC_SetPriority(OTG_HS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); diff --git a/hw/bsp/waveshare_openh743i/STM32H743IITX_FLASH.ld b/hw/bsp/waveshare_openh743i/STM32H743IITX_FLASH.ld deleted file mode 100644 index 73d2dedb..00000000 --- a/hw/bsp/waveshare_openh743i/STM32H743IITX_FLASH.ld +++ /dev/null @@ -1,175 +0,0 @@ -/* -****************************************************************************** -** -** File : LinkerScript.ld -** -** Author : STM32CubeIDE -** -** Abstract : Linker script for STM32H7 series -** 2048Kbytes FLASH and 192Kbytes RAM -** -** Set heap size, stack size and stack location according -** to application requirements. -** -** Set memory bank area and size if external memory is used. -** -** Target : STMicroelectronics STM32 -** -** Distribution: The file is distributed as is, without any warranty -** of any kind. -** -***************************************************************************** -** @attention -** -** Copyright (c) 2019 STMicroelectronics. -** All rights reserved. -** -** This software component is licensed by ST under BSD 3-Clause license, -** the "License"; You may not use this file except in compliance with the -** License. You may obtain a copy of the License at: -** opensource.org/licenses/BSD-3-Clause -** -**************************************************************************** -*/ - -/* Entry Point */ -ENTRY(Reset_Handler) - -/* Highest address of the user mode stack */ -_estack = 0x20020000; /* end of RAM */ -/* Generate a link error if heap and stack don't fit into RAM */ -_Min_Heap_Size = 0x2000 ; /* required amount of heap */ -_Min_Stack_Size = 0x2000 ; /* required amount of stack */ - -/* Specify the memory areas */ -MEMORY -{ - FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 2048K - RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K - RAM_D1 (xrw) : ORIGIN = 0x24000000, LENGTH = 512K - RAM_D2 (xrw) : ORIGIN = 0x30000000, LENGTH = 288K - RAM_D3 (xrw) : ORIGIN = 0x38000000, LENGTH = 64K - ITCMRAM (xrw) : ORIGIN = 0x00000000, LENGTH = 64K -} - -/* Define output sections */ -SECTIONS -{ - /* The startup code goes first into FLASH */ - .isr_vector : - { - . = ALIGN(4); - KEEP(*(.isr_vector)) /* Startup code */ - . = ALIGN(4); - } >FLASH - - /* The program code and other data goes into FLASH */ - .text : - { - . = ALIGN(4); - *(.text) /* .text sections (code) */ - *(.text*) /* .text* sections (code) */ - *(.glue_7) /* glue arm to thumb code */ - *(.glue_7t) /* glue thumb to arm code */ - *(.eh_frame) - - KEEP (*(.init)) - KEEP (*(.fini)) - - . = ALIGN(4); - _etext = .; /* define a global symbols at end of code */ - } >FLASH - - /* Constant data goes into FLASH */ - .rodata : - { - . = ALIGN(4); - *(.rodata) /* .rodata sections (constants, strings, etc.) */ - *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ - . = ALIGN(4); - } >FLASH - - .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH - .ARM : { - __exidx_start = .; - *(.ARM.exidx*) - __exidx_end = .; - } >FLASH - - .preinit_array : - { - PROVIDE_HIDDEN (__preinit_array_start = .); - KEEP (*(.preinit_array*)) - PROVIDE_HIDDEN (__preinit_array_end = .); - } >FLASH - .init_array : - { - PROVIDE_HIDDEN (__init_array_start = .); - KEEP (*(SORT(.init_array.*))) - KEEP (*(.init_array*)) - PROVIDE_HIDDEN (__init_array_end = .); - } >FLASH - .fini_array : - { - PROVIDE_HIDDEN (__fini_array_start = .); - KEEP (*(SORT(.fini_array.*))) - KEEP (*(.fini_array*)) - PROVIDE_HIDDEN (__fini_array_end = .); - } >FLASH - - /* used by the startup to initialize data */ - _sidata = LOADADDR(.data); - - /* Initialized data sections goes into RAM, load LMA copy after code */ - .data : - { - . = ALIGN(4); - _sdata = .; /* create a global symbol at data start */ - *(.data) /* .data sections */ - *(.data*) /* .data* sections */ - *(.RamFunc) /* .RamFunc sections */ - *(.RamFunc*) /* .RamFunc* sections */ - - . = ALIGN(4); - _edata = .; /* define a global symbol at data end */ - } >RAM AT> FLASH - - /* Uninitialized data section */ - . = ALIGN(4); - .bss : - { - /* This is used by the startup in order to initialize the .bss secion */ - _sbss = .; /* define a global symbol at bss start */ - __bss_start__ = _sbss; - *(.bss) - *(.bss*) - *(COMMON) - - . = ALIGN(4); - _ebss = .; /* define a global symbol at bss end */ - __bss_end__ = _ebss; - } >RAM - - /* User_heap_stack section, used to check that there is enough RAM left */ - ._user_heap_stack : - { - . = ALIGN(8); - PROVIDE ( end = . ); - PROVIDE ( _end = . ); - . = . + _Min_Heap_Size; - . = . + _Min_Stack_Size; - . = ALIGN(8); - } >RAM - - /* Remove information from the standard libraries */ - /DISCARD/ : - { - libc.a ( * ) - libm.a ( * ) - libgcc.a ( * ) - } - - .ARM.attributes 0 : { *(.ARM.attributes) } -} - - diff --git a/hw/bsp/waveshare_openh743i/board.c b/hw/bsp/waveshare_openh743i/board.c deleted file mode 100644 index 4468c066..00000000 --- a/hw/bsp/waveshare_openh743i/board.c +++ /dev/null @@ -1,495 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2019 - * Benjamin Evans - * William D. Jones (thor0505@comcast.net), - * Ha Thach (tinyusb.org) - * Uwe Bonnes (bon@elektron.ikp.physik.tu-darmstadt.de - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "stm32h7xx_hal.h" -#include "stm32h7xx_hal_tim.h" -#include "bsp/board.h" - - -/* ** BOARD SETUP ** - * - * NOTE: This board has bad signal integrity so you may experience some problems. - * This setup assumes you have an openh743i-c Core and breakout board. For the HS - * examples it also assumes you have a waveshare USB3300 breakout board plugged - * into the ULPI PMOD header on the openh743i-c. - * - * UART Debugging: - * Due to pin conflicts in the HS configuration, this BSP uses USART3 (PD8, PD9). - * As such, you won't be able to use the UART to USB converter on board and will - * require an external UART to USB converter. You could use the waveshare FT232 - * USB UART Board (micro) but any 3.3V UART to USB converter will be fine. - * - * Fullspeed: - * If VBUS sense is enabled, ensure the PA9-VBUS jumper is connected on the core - * board. Connect the PB6 jumper for the LED and the Wakeup - PA0 jumper for the - * button. Connect the USB cable to the USB connector on the core board. - * - * High Speed: - * Remove all jumpers from the openh743i-c (especially the USART1 jumpers as the - * pins conflict). Connect the PB6 jumper for the LED and the Wakeup - PA0 - * jumper for the button. - * - * The reset pin on the ULPI PMOD port is not connected to the MCU. You'll need - * to solder a wire from the RST pin on the USB3300 to a pin of your choosing on - * the openh743i-c board (this example assumes you've used PD14 as specified with - * the ULPI_RST_PORT and ULPI_RST_PIN defines below). - * - * Preferably power the board using the external 5VDC jack. Connect the USB cable - * to the USB connector on the ULPI board. Adjust delays in this file as required. - * - * If you're having trouble, ask a question on the tinyUSB Github Discussion boards. - * - * Have fun! - * -*/ - -//--------------------------------------------------------------------+ -// BOARD DEFINES -//--------------------------------------------------------------------+ - -//LED Pin -#define LED_PORT GPIOB -#define LED_PIN GPIO_PIN_6 -#define LED_STATE_ON 1 - -//ULPI PHY reset pin -#define ULPI_RST_PORT GPIOD -#define ULPI_RST_PIN GPIO_PIN_14 - -// Tamper push-button -#define BUTTON_PORT GPIOA -#define BUTTON_PIN GPIO_PIN_0 -#define BUTTON_STATE_ACTIVE 1 - -// Need external UART to USB converter as USART1 pins conflict with HS ULPI pins -#define UART_DEV USART3 -#define UART_CLK_EN __HAL_RCC_USART3_CLK_ENABLE -#define UART_GPIO_PORT GPIOD -#define UART_GPIO_AF GPIO_AF7_USART3 -#define UART_TX_PIN GPIO_PIN_8 -#define UART_RX_PIN GPIO_PIN_9 - -// VBUS Sense detection -#define OTG_FS_VBUS_SENSE 1 -#define OTG_HS_VBUS_SENSE 0 - - -//--------------------------------------------------------------------+ -// MACRO TYPEDEF CONSTANT ENUM -//--------------------------------------------------------------------+ - -UART_HandleTypeDef uartHandle; -TIM_HandleTypeDef tim2Handle; - - -//--------------------------------------------------------------------+ -// Forward USB interrupt events to TinyUSB IRQ Handler -//--------------------------------------------------------------------+ - -// Despite being call USB2_OTG -// OTG_FS is marked as RHPort0 by TinyUSB to be consistent across stm32 port -void OTG_FS_IRQHandler(void) -{ - tud_int_handler(0); -} - -// Despite being call USB2_OTG -// OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port -void OTG_HS_IRQHandler(void) -{ - tud_int_handler(1); -} - - -//--------------------------------------------------------------------+ -// RCC Clock -//--------------------------------------------------------------------+ -static inline void board_stm32h7_clock_init(void) -{ - RCC_OscInitTypeDef RCC_OscInitStruct = {0}; - RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; - RCC_PeriphCLKInitTypeDef PeriphClkInitStruct = {0}; - - __HAL_RCC_SYSCFG_CLK_ENABLE(); - - // Supply configuration update enable - HAL_PWREx_ConfigSupply(PWR_LDO_SUPPLY); - - // Configure the main internal regulator output voltage - __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE0); - - while (!__HAL_PWR_GET_FLAG(PWR_FLAG_VOSRDY)) - { - } - // Macro to configure the PLL clock source - __HAL_RCC_PLL_PLLSOURCE_CONFIG(RCC_PLLSOURCE_HSE); - - // Initializes the RCC Oscillators according to the specified parameters in the RCC_OscInitTypeDef structure. - RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; - RCC_OscInitStruct.HSEState = RCC_HSE_ON; - RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; - RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; - RCC_OscInitStruct.PLL.PLLM = 2; - RCC_OscInitStruct.PLL.PLLN = 240; - RCC_OscInitStruct.PLL.PLLP = 2; - RCC_OscInitStruct.PLL.PLLQ = 2; - RCC_OscInitStruct.PLL.PLLR = 2; - RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1VCIRANGE_2; - RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1VCOWIDE; - RCC_OscInitStruct.PLL.PLLFRACN = 0; - HAL_RCC_OscConfig(&RCC_OscInitStruct); - - PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB | RCC_PERIPHCLK_USART3; - PeriphClkInitStruct.PLL3.PLL3M = 8; - PeriphClkInitStruct.PLL3.PLL3N = 336; - PeriphClkInitStruct.PLL3.PLL3P = 2; - PeriphClkInitStruct.PLL3.PLL3Q = 7; - PeriphClkInitStruct.PLL3.PLL3R = 2; - PeriphClkInitStruct.PLL3.PLL3RGE = RCC_PLL3VCIRANGE_0; - PeriphClkInitStruct.PLL3.PLL3VCOSEL = RCC_PLL3VCOWIDE; - PeriphClkInitStruct.PLL3.PLL3FRACN = 0; - PeriphClkInitStruct.Usart234578ClockSelection = RCC_USART234578CLKSOURCE_PLL3; - PeriphClkInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_PLL3; - HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct); - - // Initializes the CPU, AHB and APB buses clocks - RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2 | RCC_CLOCKTYPE_D3PCLK1 | RCC_CLOCKTYPE_D1PCLK1; - RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; - RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1; - RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV2; - RCC_ClkInitStruct.APB3CLKDivider = RCC_APB3_DIV2; - RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV2; - RCC_ClkInitStruct.APB2CLKDivider = RCC_APB2_DIV2; - RCC_ClkInitStruct.APB4CLKDivider = RCC_APB4_DIV2; - HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2); - - __HAL_RCC_CSI_ENABLE(); - - // Enable SYSCFG clock mondatory for I/O Compensation Cell - __HAL_RCC_SYSCFG_CLK_ENABLE(); - - // Enables the I/O Compensation Cell - HAL_EnableCompensationCell(); - - // Enable voltage detector - HAL_PWREx_EnableUSBVoltageDetector(); - - return; -} - - -//--------------------------------------------------------------------+ -// Timer implementation for board delay -// This should be OS safe and doesn't require the scheduler to be running -//--------------------------------------------------------------------+ -static void init_timer(void) -{ - TIM_ClockConfigTypeDef sClockSourceConfig = {0}; - - __HAL_RCC_TIM2_CLK_ENABLE(); - - //Assuming timer clock is running at 260Mhz this should configure the timer counter to 1000Hz - tim2Handle.Instance = TIM2; - tim2Handle.Init.Prescaler = 60000U - 1U; - tim2Handle.Init.CounterMode = TIM_COUNTERMODE_UP; - tim2Handle.Init.Period = 0xFFFFFFFFU; - tim2Handle.Init.ClockDivision = TIM_CLOCKDIVISION_DIV4; - tim2Handle.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE; - HAL_TIM_Base_Init(&tim2Handle); - - sClockSourceConfig.ClockSource = TIM_CLOCKSOURCE_INTERNAL; - HAL_TIM_ConfigClockSource(&tim2Handle, &sClockSourceConfig); - - //Start the timer - HAL_TIM_Base_Start(&tim2Handle); - - return; -} - - -// Custom board delay implementation using timer ticks -static inline void timer_board_delay(uint32_t ms) -{ - uint32_t startMs = __HAL_TIM_GET_COUNTER(&tim2Handle); - while ((__HAL_TIM_GET_COUNTER(&tim2Handle) - startMs) < ms) - { - asm("nop"); //do nothing - } -} - - -//Board initialisation -void board_init(void) -{ - GPIO_InitTypeDef GPIO_InitStruct; - - // Init clocks - board_stm32h7_clock_init(); - - // Init timer for delays - init_timer(); - - //Disable systick for now - //If using an RTOS and the systick interrupt fires without the scheduler running you might have an issue - //Because this init code now introduces delays, the systick should be disabled until after board init - SysTick->CTRL &= ~1U; - - // Enable GPIO clocks - __HAL_RCC_GPIOA_CLK_ENABLE(); - __HAL_RCC_GPIOB_CLK_ENABLE(); - __HAL_RCC_GPIOC_CLK_ENABLE(); - __HAL_RCC_GPIOD_CLK_ENABLE(); - __HAL_RCC_GPIOH_CLK_ENABLE(); - __HAL_RCC_GPIOI_CLK_ENABLE(); - - // Enable UART Clock - UART_CLK_EN(); - -#if CFG_TUSB_OS == OPT_OS_FREERTOS - // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) - NVIC_SetPriority(OTG_FS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); - NVIC_SetPriority(OTG_HS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); -#endif - - // LED - GPIO_InitStruct.Pin = LED_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; - GPIO_InitStruct.Pull = GPIO_PULLUP; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); - - // PHY RST Pin - GPIO_InitStruct.Pin = ULPI_RST_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; - HAL_GPIO_Init(ULPI_RST_PORT, &GPIO_InitStruct); - HAL_GPIO_WritePin(ULPI_RST_PORT, ULPI_RST_PIN, 0U); - - // Button - GPIO_InitStruct.Pin = BUTTON_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_INPUT; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); - - // Uart - GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_PULLUP; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; - GPIO_InitStruct.Alternate = UART_GPIO_AF; - HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct); - - uartHandle.Instance = UART_DEV; - uartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; - uartHandle.Init.WordLength = UART_WORDLENGTH_8B; - uartHandle.Init.StopBits = UART_STOPBITS_1; - uartHandle.Init.Parity = UART_PARITY_NONE; - uartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE; - uartHandle.Init.Mode = UART_MODE_TX_RX; - uartHandle.Init.OverSampling = UART_OVERSAMPLING_16; - HAL_UART_Init(&uartHandle); - -#if BOARD_DEVICE_RHPORT_NUM == 0 - //Full Speed - - // Configure DM DP Pins - GPIO_InitStruct.Pin = GPIO_PIN_11 | GPIO_PIN_12; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - // This for ID line debug - GPIO_InitStruct.Pin = GPIO_PIN_10; - GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; - GPIO_InitStruct.Pull = GPIO_PULLUP; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - __HAL_RCC_USB2_OTG_FS_CLK_ENABLE(); - -#if OTG_FS_VBUS_SENSE - // Configure VBUS Pin - GPIO_InitStruct.Pin = GPIO_PIN_9; - GPIO_InitStruct.Mode = GPIO_MODE_INPUT; - GPIO_InitStruct.Pull = GPIO_NOPULL; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - // Enable VBUS sense (B device) via pin PA9 - USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN; -#else - // Disable VBUS sense (B device) via pin PA9 - USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; - - // B-peripheral session valid override enable - USB_OTG_FS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; - USB_OTG_FS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; -#endif // vbus sense - -#elif BOARD_DEVICE_RHPORT_NUM == 1 - //High Speed - - /**USB_OTG_HS GPIO Configuration - PC0 ------> USB_OTG_HS_ULPI_STP - PC2_C ------> USB_OTG_HS_ULPI_DIR - PC3_C ------> USB_OTG_HS_ULPI_NXT - PA3 ------> USB_OTG_HS_ULPI_D0 - PA5 ------> USB_OTG_HS_ULPI_CK - PB1 ------> USB_OTG_HS_ULPI_D2 - PB10 ------> USB_OTG_HS_ULPI_D3 - PB11 ------> USB_OTG_HS_ULPI_D4 - PB12 ------> USB_OTG_HS_ULPI_D5 - PB13 ------> USB_OTG_HS_ULPI_D6 - PB5 ------> USB_OTG_HS_ULPI_D7 - */ - - GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_2 | GPIO_PIN_3; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; - HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); - - GPIO_InitStruct.Pin = GPIO_PIN_3 | GPIO_PIN_5; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12 | GPIO_PIN_13 | GPIO_PIN_5; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; - HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); - - // Peripheral clock enable - __HAL_RCC_USB_OTG_HS_CLK_ENABLE(); - __HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE(); - -#if OTG_HS_VBUS_SENSE -#error OTG HS VBUS Sense enabled is not implemented -#else - // No VBUS sense - USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; - - // B-peripheral session valid override enable - USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; - USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; -#endif - - // Force device mode - USB_OTG_HS->GUSBCFG &= ~USB_OTG_GUSBCFG_FHMOD; - USB_OTG_HS->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD; - - //Reset the PHY - Change the delays as you see fit - timer_board_delay(5U); //Delay 5ms - HAL_GPIO_WritePin(ULPI_RST_PORT, ULPI_RST_PIN, 1U); - timer_board_delay(20U); //Delay 20ms - HAL_GPIO_WritePin(ULPI_RST_PORT, ULPI_RST_PIN, 0U); - timer_board_delay(20U); //Delay 20ms - -#endif // rhport = 1 - - //Disable the timer used for delays - HAL_TIM_Base_Stop(&tim2Handle); - __HAL_RCC_TIM2_CLK_DISABLE(); - - // Configure systick 1ms tick timer - SysTick_Config(SystemCoreClock / 1000); - - //Enable systick - SysTick->CTRL |= ~1U; - - return; -} - - -//--------------------------------------------------------------------+ -// Board porting API -//--------------------------------------------------------------------+ -void board_led_write(bool state) -{ - HAL_GPIO_WritePin(LED_PORT, LED_PIN, state ? LED_STATE_ON : (1 - LED_STATE_ON)); -} - - -uint32_t board_button_read(void) -{ - return (BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN)) ? 1 : 0; -} - - -int board_uart_read(uint8_t *buf, int len) -{ - (void)buf; - (void)len; - return 0; -} - - -int board_uart_write(void const *buf, int len) -{ - HAL_UART_Transmit(&uartHandle, (uint8_t *)buf, len, 0xffff); - return len; -} - - -#if CFG_TUSB_OS == OPT_OS_NONE -volatile uint32_t system_ticks = 0; -void SysTick_Handler(void) -{ - system_ticks++; -} - - -uint32_t board_millis(void) -{ - return system_ticks; -} -#endif - - -void HardFault_Handler(void) -{ - asm("bkpt"); -} - - -// Required by __libc_init_array in startup code if we are compiling using -// -nostdlib/-nostartfiles. -void _init(void) -{ -} \ No newline at end of file diff --git a/hw/bsp/waveshare_openh743i/board.mk b/hw/bsp/waveshare_openh743i/board.mk deleted file mode 100644 index 721df1bd..00000000 --- a/hw/bsp/waveshare_openh743i/board.mk +++ /dev/null @@ -1,64 +0,0 @@ -UF2_FAMILY_ID = 0x6db66082 -ST_FAMILY = h7 -DEPS_SUBMODULES += lib/CMSIS_5 hw/mcu/st/cmsis_device_$(ST_FAMILY) hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver - -ST_CMSIS = hw/mcu/st/cmsis_device_$(ST_FAMILY) -ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver - -# Default is HS port -PORT ?= 1 - -SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32h743xx.s -LD_FILE = $(BOARD_PATH)/STM32H743IITX_FLASH.ld - -CFLAGS += \ - -flto \ - -mthumb \ - -mabi=aapcs \ - -mcpu=cortex-m7 \ - -mfloat-abi=hard \ - -mfpu=fpv5-d16 \ - -nostdlib -nostartfiles \ - -DCFG_TUSB_MCU=OPT_MCU_STM32H7 \ - -DBOARD_DEVICE_RHPORT_NUM=$(PORT) \ - -DSTM32H743xx \ - -DHSE_VALUE=8000000 - -ifeq ($(PORT), 1) - CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED - $(info "PORT1 High Speed") -else - $(info "PORT0 Full Speed") -endif - -# suppress warning caused by vendor mcu driver -CFLAGS += -Wno-error=maybe-uninitialized -Wno-error=cast-align - -# All source paths should be relative to the top level. -SRC_C += \ - src/portable/st/synopsys/dcd_synopsys.c \ - $(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_uart.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_pwr_ex.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_tim.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_tim_ex.c - -INC += \ - $(TOP)/$(BOARD_PATH) \ - $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \ - $(TOP)/$(ST_CMSIS)/Include \ - $(TOP)/$(ST_HAL_DRIVER)/Inc - -# For freeRTOS port source -FREERTOS_PORT = ARM_CM7/r0p1 - -# For flash-jlink target -JLINK_DEVICE = stm32h743ii - -# flash target using jlink -flash: flash-jlink \ No newline at end of file diff --git a/hw/bsp/waveshare_openh743i/stm32h7xx_hal_conf.h b/hw/bsp/waveshare_openh743i/stm32h7xx_hal_conf.h deleted file mode 100644 index 11d29ed6..00000000 --- a/hw/bsp/waveshare_openh743i/stm32h7xx_hal_conf.h +++ /dev/null @@ -1,483 +0,0 @@ -/** - ****************************************************************************** - * @file stm32h7xx_hal_conf_template.h - * @brief HAL configuration template file. - * This file should be copied to the application folder and renamed - * to stm32h7xx_hal_conf.h. - ****************************************************************************** - * @attention - * - *

© COPYRIGHT(c) 2019 STMicroelectronics

- * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32H7xx_HAL_CONF_H -#define __STM32H7xx_HAL_CONF_H - -#ifdef __cplusplus - extern "C" { -#endif - -/* Exported types ------------------------------------------------------------*/ -/* Exported constants --------------------------------------------------------*/ - -/* ########################## Module Selection ############################## */ -/** - * @brief This is the list of modules to be used in the HAL driver - */ -#define HAL_MODULE_ENABLED -#define HAL_ADC_MODULE_ENABLED -/* #define HAL_CEC_MODULE_ENABLED */ -/* #define HAL_COMP_MODULE_ENABLED */ -#define HAL_CORTEX_MODULE_ENABLED -/* #define HAL_CRC_MODULE_ENABLED */ -/* #define HAL_CRYP_MODULE_ENABLED */ -/* #define HAL_DAC_MODULE_ENABLED */ -/* #define HAL_DCMI_MODULE_ENABLED */ -/* #define HAL_DFSDM_MODULE_ENABLED */ -#define HAL_DMA_MODULE_ENABLED -/* #define HAL_DMA2D_MODULE_ENABLED */ -/* #define HAL_ETH_MODULE_ENABLED */ -/* #define HAL_EXTI_MODULE_ENABLED */ -/* #define HAL_FDCAN_MODULE_ENABLED */ -#define HAL_FLASH_MODULE_ENABLED -#define HAL_GPIO_MODULE_ENABLED -/* #define HAL_HASH_MODULE_ENABLED */ -/* #define HAL_HCD_MODULE_ENABLED */ -/* #define HAL_HRTIM_MODULE_ENABLED */ -/* #define HAL_HSEM_MODULE_ENABLED */ -/* #define HAL_I2C_MODULE_ENABLED */ -/* #define HAL_I2S_MODULE_ENABLED */ -/* #define HAL_IRDA_MODULE_ENABLED */ -/* #define HAL_IWDG_MODULE_ENABLED */ -/* #define HAL_JPEG_MODULE_ENABLED */ -/* #define HAL_LPTIM_MODULE_ENABLED */ -/* #define HAL_LTDC_MODULE_ENABLED */ -/* #define HAL_MDIOS_MODULE_ENABLED */ -/* #define HAL_MDMA_MODULE_ENABLED */ -/* #define HAL_MMC_MODULE_ENABLED */ -/* #define HAL_NAND_MODULE_ENABLED */ -/* #define HAL_NOR_MODULE_ENABLED */ -/* #define HAL_OPAMP_MODULE_ENABLED */ -/* #define HAL_PCD_MODULE_ENABLED */ -#define HAL_PWR_MODULE_ENABLED -/* #define HAL_QSPI_MODULE_ENABLED */ -/* #define HAL_RAMECC_MODULE_ENABLED */ -#define HAL_RCC_MODULE_ENABLED -/* #define HAL_RNG_MODULE_ENABLED */ -/* #define HAL_RTC_MODULE_ENABLED */ -/* #define HAL_SAI_MODULE_ENABLED */ -/* #define HAL_SD_MODULE_ENABLED */ -/* #define HAL_SDRAM_MODULE_ENABLED */ -/* #define HAL_SMARTCARD_MODULE_ENABLED */ -/* #define HAL_SMBUS_MODULE_ENABLED */ -/* #define HAL_SPDIFRX_MODULE_ENABLED */ -#define HAL_SPI_MODULE_ENABLED -/* #define HAL_SRAM_MODULE_ENABLED */ -/* #define HAL_SWPMI_MODULE_ENABLED */ -#define HAL_TIM_MODULE_ENABLED -#define HAL_UART_MODULE_ENABLED -/* #define HAL_USART_MODULE_ENABLED */ -/* #define HAL_WWDG_MODULE_ENABLED */ - -/* ########################## Oscillator Values adaptation ####################*/ -/** - * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. - * This value is used by the RCC HAL module to compute the system frequency - * (when HSE is used as system clock source, directly or through the PLL). - */ -#if !defined (HSE_VALUE) -//#define HSE_VALUE ((uint32_t)25000000) /*!< Value of the External oscillator in Hz */ -#error HSE_VALUE is not defined -#endif /* HSE_VALUE */ - -#if !defined (HSE_STARTUP_TIMEOUT) - #define HSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSE start up, in ms */ -#endif /* HSE_STARTUP_TIMEOUT */ - -/** - * @brief Internal oscillator (CSI) default value. - * This value is the default CSI value after Reset. - */ -#if !defined (CSI_VALUE) - #define CSI_VALUE ((uint32_t)4000000) /*!< Value of the Internal oscillator in Hz*/ -#endif /* CSI_VALUE */ - -/** - * @brief Internal High Speed oscillator (HSI) value. - * This value is used by the RCC HAL module to compute the system frequency - * (when HSI is used as system clock source, directly or through the PLL). - */ -#if !defined (HSI_VALUE) - #define HSI_VALUE ((uint32_t)64000000) /*!< Value of the Internal oscillator in Hz*/ -#endif /* HSI_VALUE */ - -/** - * @brief External Low Speed oscillator (LSE) value. - * This value is used by the UART, RTC HAL module to compute the system frequency - */ -#if !defined (LSE_VALUE) - #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/ -#endif /* LSE_VALUE */ - - -#if !defined (LSE_STARTUP_TIMEOUT) - #define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */ -#endif /* LSE_STARTUP_TIMEOUT */ - -#if !defined (LSI_VALUE) - #define LSI_VALUE ((uint32_t)32000) /*!< LSI Typical Value in Hz*/ -#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz - The real value may vary depending on the variations - in voltage and temperature.*/ - -/** - * @brief External clock source for I2S peripheral - * This value is used by the I2S HAL module to compute the I2S clock source - * frequency, this source is inserted directly through I2S_CKIN pad. - */ -#if !defined (EXTERNAL_CLOCK_VALUE) - #define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the External clock in Hz*/ -#endif /* EXTERNAL_CLOCK_VALUE */ - -/* Tip: To avoid modifying this file each time you need to use different HSE, - === you can define the HSE value in your toolchain compiler preprocessor. */ - -/* ########################### System Configuration ######################### */ -/** - * @brief This is the HAL system configuration section - */ -#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ -#define TICK_INT_PRIORITY ((uint32_t)0x0F) /*!< tick interrupt priority */ -#define USE_RTOS 0 -#define USE_SD_TRANSCEIVER 1U /*!< use uSD Transceiver */ -#define USE_SPI_CRC 1U /*!< use CRC in SPI */ - -#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ -#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ -#define USE_HAL_COMP_REGISTER_CALLBACKS 0U /* COMP register callback disabled */ -#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ -#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ -#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ -#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */ -#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */ -#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */ -#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ -#define USE_HAL_FDCAN_REGISTER_CALLBACKS 0U /* FDCAN register callback disabled */ -#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ -#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ -#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */ -#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ -#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ -#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ -#define USE_HAL_HRTIM_REGISTER_CALLBACKS 0U /* HRTIM register callback disabled */ -#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ -#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ -#define USE_HAL_JPEG_REGISTER_CALLBACKS 0U /* JPEG register callback disabled */ -#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */ -#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */ -#define USE_HAL_MDIOS_REGISTER_CALLBACKS 0U /* MDIO register callback disabled */ -#define USE_HAL_OPAMP_REGISTER_CALLBACKS 0U /* MDIO register callback disabled */ -#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ -#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */ -#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ -#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ -#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */ -#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */ -#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ -#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ -#define USE_HAL_SWPMI_REGISTER_CALLBACKS 0U /* SWPMI register callback disabled */ -#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ -#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ -#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ -#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ - -/* ########################### Ethernet Configuration ######################### */ -#define ETH_TX_DESC_CNT 4 /* number of Ethernet Tx DMA descriptors */ -#define ETH_RX_DESC_CNT 4 /* number of Ethernet Rx DMA descriptors */ - -#define ETH_MAC_ADDR0 ((uint8_t)0x02) -#define ETH_MAC_ADDR1 ((uint8_t)0x00) -#define ETH_MAC_ADDR2 ((uint8_t)0x00) -#define ETH_MAC_ADDR3 ((uint8_t)0x00) -#define ETH_MAC_ADDR4 ((uint8_t)0x00) -#define ETH_MAC_ADDR5 ((uint8_t)0x00) - -/* ########################## Assert Selection ############################## */ -/** - * @brief Uncomment the line below to expanse the "assert_param" macro in the - * HAL drivers code - */ -/* #define USE_FULL_ASSERT 1 */ - - -/* Includes ------------------------------------------------------------------*/ -/** - * @brief Include module's header file - */ - -#ifdef HAL_RCC_MODULE_ENABLED - #include "stm32h7xx_hal_rcc.h" -#endif /* HAL_RCC_MODULE_ENABLED */ - -#ifdef HAL_GPIO_MODULE_ENABLED - #include "stm32h7xx_hal_gpio.h" -#endif /* HAL_GPIO_MODULE_ENABLED */ - -#ifdef HAL_DMA_MODULE_ENABLED - #include "stm32h7xx_hal_dma.h" -#endif /* HAL_DMA_MODULE_ENABLED */ - -#ifdef HAL_MDMA_MODULE_ENABLED - #include "stm32h7xx_hal_mdma.h" -#endif /* HAL_MDMA_MODULE_ENABLED */ - -#ifdef HAL_HASH_MODULE_ENABLED - #include "stm32h7xx_hal_hash.h" -#endif /* HAL_HASH_MODULE_ENABLED */ - -#ifdef HAL_DCMI_MODULE_ENABLED - #include "stm32h7xx_hal_dcmi.h" -#endif /* HAL_DCMI_MODULE_ENABLED */ - -#ifdef HAL_DMA2D_MODULE_ENABLED - #include "stm32h7xx_hal_dma2d.h" -#endif /* HAL_DMA2D_MODULE_ENABLED */ - -#ifdef HAL_DSI_MODULE_ENABLED - #include "stm32h7xx_hal_dsi.h" -#endif /* HAL_DSI_MODULE_ENABLED */ - -#ifdef HAL_DFSDM_MODULE_ENABLED - #include "stm32h7xx_hal_dfsdm.h" -#endif /* HAL_DFSDM_MODULE_ENABLED */ - -#ifdef HAL_ETH_MODULE_ENABLED - #include "stm32h7xx_hal_eth.h" -#endif /* HAL_ETH_MODULE_ENABLED */ - -#ifdef HAL_EXTI_MODULE_ENABLED - #include "stm32h7xx_hal_exti.h" -#endif /* HAL_EXTI_MODULE_ENABLED */ - -#ifdef HAL_CORTEX_MODULE_ENABLED - #include "stm32h7xx_hal_cortex.h" -#endif /* HAL_CORTEX_MODULE_ENABLED */ - -#ifdef HAL_ADC_MODULE_ENABLED - #include "stm32h7xx_hal_adc.h" -#endif /* HAL_ADC_MODULE_ENABLED */ - -#ifdef HAL_FDCAN_MODULE_ENABLED - #include "stm32h7xx_hal_fdcan.h" -#endif /* HAL_FDCAN_MODULE_ENABLED */ - -#ifdef HAL_CEC_MODULE_ENABLED - #include "stm32h7xx_hal_cec.h" -#endif /* HAL_CEC_MODULE_ENABLED */ - -#ifdef HAL_COMP_MODULE_ENABLED - #include "stm32h7xx_hal_comp.h" -#endif /* HAL_COMP_MODULE_ENABLED */ - -#ifdef HAL_CRC_MODULE_ENABLED - #include "stm32h7xx_hal_crc.h" -#endif /* HAL_CRC_MODULE_ENABLED */ - -#ifdef HAL_CRYP_MODULE_ENABLED - #include "stm32h7xx_hal_cryp.h" -#endif /* HAL_CRYP_MODULE_ENABLED */ - -#ifdef HAL_DAC_MODULE_ENABLED - #include "stm32h7xx_hal_dac.h" -#endif /* HAL_DAC_MODULE_ENABLED */ - -#ifdef HAL_FLASH_MODULE_ENABLED - #include "stm32h7xx_hal_flash.h" -#endif /* HAL_FLASH_MODULE_ENABLED */ - -#ifdef HAL_HRTIM_MODULE_ENABLED - #include "stm32h7xx_hal_hrtim.h" -#endif /* HAL_HRTIM_MODULE_ENABLED */ - -#ifdef HAL_HSEM_MODULE_ENABLED - #include "stm32h7xx_hal_hsem.h" -#endif /* HAL_HSEM_MODULE_ENABLED */ - -#ifdef HAL_SRAM_MODULE_ENABLED - #include "stm32h7xx_hal_sram.h" -#endif /* HAL_SRAM_MODULE_ENABLED */ - -#ifdef HAL_NOR_MODULE_ENABLED - #include "stm32h7xx_hal_nor.h" -#endif /* HAL_NOR_MODULE_ENABLED */ - -#ifdef HAL_NAND_MODULE_ENABLED - #include "stm32h7xx_hal_nand.h" -#endif /* HAL_NAND_MODULE_ENABLED */ - -#ifdef HAL_I2C_MODULE_ENABLED - #include "stm32h7xx_hal_i2c.h" -#endif /* HAL_I2C_MODULE_ENABLED */ - -#ifdef HAL_I2S_MODULE_ENABLED - #include "stm32h7xx_hal_i2s.h" -#endif /* HAL_I2S_MODULE_ENABLED */ - -#ifdef HAL_IWDG_MODULE_ENABLED - #include "stm32h7xx_hal_iwdg.h" -#endif /* HAL_IWDG_MODULE_ENABLED */ - -#ifdef HAL_JPEG_MODULE_ENABLED - #include "stm32h7xx_hal_jpeg.h" -#endif /* HAL_JPEG_MODULE_ENABLED */ - -#ifdef HAL_MDIOS_MODULE_ENABLED - #include "stm32h7xx_hal_mdios.h" -#endif /* HAL_MDIOS_MODULE_ENABLED */ - -#ifdef HAL_MMC_MODULE_ENABLED - #include "stm32h7xx_hal_mmc.h" -#endif /* HAL_MMC_MODULE_ENABLED */ - -#ifdef HAL_LPTIM_MODULE_ENABLED -#include "stm32h7xx_hal_lptim.h" -#endif /* HAL_LPTIM_MODULE_ENABLED */ - -#ifdef HAL_LTDC_MODULE_ENABLED -#include "stm32h7xx_hal_ltdc.h" -#endif /* HAL_LTDC_MODULE_ENABLED */ - -#ifdef HAL_OPAMP_MODULE_ENABLED -#include "stm32h7xx_hal_opamp.h" -#endif /* HAL_OPAMP_MODULE_ENABLED */ - -#ifdef HAL_PWR_MODULE_ENABLED - #include "stm32h7xx_hal_pwr.h" -#endif /* HAL_PWR_MODULE_ENABLED */ - -#ifdef HAL_QSPI_MODULE_ENABLED - #include "stm32h7xx_hal_qspi.h" -#endif /* HAL_QSPI_MODULE_ENABLED */ - -#ifdef HAL_RAMECC_MODULE_ENABLED - #include "stm32h7xx_hal_ramecc.h" -#endif /* HAL_HCD_MODULE_ENABLED */ - -#ifdef HAL_RNG_MODULE_ENABLED - #include "stm32h7xx_hal_rng.h" -#endif /* HAL_RNG_MODULE_ENABLED */ - -#ifdef HAL_RTC_MODULE_ENABLED - #include "stm32h7xx_hal_rtc.h" -#endif /* HAL_RTC_MODULE_ENABLED */ - -#ifdef HAL_SAI_MODULE_ENABLED - #include "stm32h7xx_hal_sai.h" -#endif /* HAL_SAI_MODULE_ENABLED */ - -#ifdef HAL_SD_MODULE_ENABLED - #include "stm32h7xx_hal_sd.h" -#endif /* HAL_SD_MODULE_ENABLED */ - -#ifdef HAL_SDRAM_MODULE_ENABLED - #include "stm32h7xx_hal_sdram.h" -#endif /* HAL_SDRAM_MODULE_ENABLED */ - -#ifdef HAL_SPI_MODULE_ENABLED - #include "stm32h7xx_hal_spi.h" -#endif /* HAL_SPI_MODULE_ENABLED */ - -#ifdef HAL_SPDIFRX_MODULE_ENABLED - #include "stm32h7xx_hal_spdifrx.h" -#endif /* HAL_SPDIFRX_MODULE_ENABLED */ - -#ifdef HAL_SWPMI_MODULE_ENABLED - #include "stm32h7xx_hal_swpmi.h" -#endif /* HAL_SWPMI_MODULE_ENABLED */ - -#ifdef HAL_TIM_MODULE_ENABLED - #include "stm32h7xx_hal_tim.h" -#endif /* HAL_TIM_MODULE_ENABLED */ - -#ifdef HAL_UART_MODULE_ENABLED - #include "stm32h7xx_hal_uart.h" -#endif /* HAL_UART_MODULE_ENABLED */ - -#ifdef HAL_USART_MODULE_ENABLED - #include "stm32h7xx_hal_usart.h" -#endif /* HAL_USART_MODULE_ENABLED */ - -#ifdef HAL_IRDA_MODULE_ENABLED - #include "stm32h7xx_hal_irda.h" -#endif /* HAL_IRDA_MODULE_ENABLED */ - -#ifdef HAL_SMARTCARD_MODULE_ENABLED - #include "stm32h7xx_hal_smartcard.h" -#endif /* HAL_SMARTCARD_MODULE_ENABLED */ - -#ifdef HAL_SMBUS_MODULE_ENABLED - #include "stm32h7xx_hal_smbus.h" -#endif /* HAL_SMBUS_MODULE_ENABLED */ - -#ifdef HAL_WWDG_MODULE_ENABLED - #include "stm32h7xx_hal_wwdg.h" -#endif /* HAL_WWDG_MODULE_ENABLED */ - -#ifdef HAL_PCD_MODULE_ENABLED - #include "stm32h7xx_hal_pcd.h" -#endif /* HAL_PCD_MODULE_ENABLED */ - -#ifdef HAL_HCD_MODULE_ENABLED - #include "stm32h7xx_hal_hcd.h" -#endif /* HAL_HCD_MODULE_ENABLED */ - -/* Exported macro ------------------------------------------------------------*/ -#ifdef USE_FULL_ASSERT -/** - * @brief The assert_param macro is used for function's parameters check. - * @param expr: If expr is false, it calls assert_failed function - * which reports the name of the source file and the source - * line number of the call that failed. - * If expr is true, it returns no value. - * @retval None - */ - #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) -/* Exported functions ------------------------------------------------------- */ - void assert_failed(uint8_t *file, uint32_t line); -#else - #define assert_param(expr) ((void)0U) -#endif /* USE_FULL_ASSERT */ - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32H7xx_HAL_CONF_H */ - - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/