diff --git a/hw/bsp/stm32f7/boards/stm32f723disco/board.h b/hw/bsp/stm32f7/boards/stm32f723disco/board.h new file mode 100644 index 000000000..04e0613de --- /dev/null +++ b/hw/bsp/stm32f7/boards/stm32f723disco/board.h @@ -0,0 +1,98 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2021, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef BOARD_H_ +#define BOARD_H_ + +#ifdef __cplusplus + extern "C" { +#endif + +#define LED_PORT GPIOB +#define LED_PIN GPIO_PIN_1 +#define LED_STATE_ON 1 + +#define BUTTON_PORT GPIOA +#define BUTTON_PIN GPIO_PIN_0 +#define BUTTON_STATE_ACTIVE 1 + +#define UART_DEV USART6 +#define UART_CLK_EN __HAL_RCC_USART6_CLK_ENABLE +#define UART_GPIO_PORT GPIOC +#define UART_GPIO_AF GPIO_AF8_USART6 +#define UART_TX_PIN GPIO_PIN_6 +#define UART_RX_PIN GPIO_PIN_7 + +//--------------------------------------------------------------------+ +// RCC Clock +//--------------------------------------------------------------------+ +static inline void board_clock_init(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + + /* Enable Power Control clock */ + __HAL_RCC_PWR_CLK_ENABLE(); + + /* The voltage scaling allows optimizing the power consumption when the device is + clocked below the maximum system frequency, to update the voltage scaling value + regarding system frequency refer to product datasheet. */ + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); + + /* Enable HSE Oscillator and activate PLL with HSE as source */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000; + RCC_OscInitStruct.PLL.PLLN = 432; + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; + RCC_OscInitStruct.PLL.PLLQ = 9; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + /* Activate the OverDrive to reach the 216 MHz Frequency */ + HAL_PWREx_EnableOverDrive(); + + /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; + + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7); +} + +//static inline void board_vbus_sense_init(void) +//{ +// +//} + +#ifdef __cplusplus + } +#endif + +#endif /* BOARD_H_ */ diff --git a/hw/bsp/stm32f767nucleo/STM32F767ZITx_FLASH.ld b/hw/bsp/stm32f7/boards/stm32f767nucleo/STM32F767ZITx_FLASH.ld similarity index 100% rename from hw/bsp/stm32f767nucleo/STM32F767ZITx_FLASH.ld rename to hw/bsp/stm32f7/boards/stm32f767nucleo/STM32F767ZITx_FLASH.ld diff --git a/hw/bsp/stm32f7/boards/stm32f767nucleo/board.h b/hw/bsp/stm32f7/boards/stm32f767nucleo/board.h new file mode 100644 index 000000000..046db27b4 --- /dev/null +++ b/hw/bsp/stm32f7/boards/stm32f767nucleo/board.h @@ -0,0 +1,95 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2021, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef BOARD_H_ +#define BOARD_H_ + +#ifdef __cplusplus + extern "C" { +#endif + +#define LED_PORT GPIOB +#define LED_PIN GPIO_PIN_14 +#define LED_STATE_ON 1 + +#define BUTTON_PORT GPIOC +#define BUTTON_PIN GPIO_PIN_13 +#define BUTTON_STATE_ACTIVE 1 + +#define UART_DEV USART3 +#define UART_CLK_EN __HAL_RCC_USART3_CLK_ENABLE +#define UART_GPIO_PORT GPIOD +#define UART_GPIO_AF GPIO_AF7_USART3 +#define UART_TX_PIN GPIO_PIN_8 +#define UART_RX_PIN GPIO_PIN_9 + +//--------------------------------------------------------------------+ +// RCC Clock +//--------------------------------------------------------------------+ +static inline void board_clock_init(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + + /* Enable Power Control clock */ + __HAL_RCC_PWR_CLK_ENABLE(); + + /* The voltage scaling allows optimizing the power consumption when the device is + clocked below the maximum system frequency, to update the voltage scaling value + regarding system frequency refer to product datasheet. */ + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); + + /* Enable HSE Oscillator and activate PLL with HSE as source */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000; + RCC_OscInitStruct.PLL.PLLN = 432; + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; + RCC_OscInitStruct.PLL.PLLQ = 9; + RCC_OscInitStruct.PLL.PLLR = 7; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + /* Activate the OverDrive to reach the 216 MHz Frequency */ + HAL_PWREx_EnableOverDrive(); + + /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; + + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7); +} + + +#ifdef __cplusplus + } +#endif + +#endif /* BOARD_H_ */ diff --git a/hw/bsp/stm32f7/boards/stm32f767nucleo/board.mk b/hw/bsp/stm32f7/boards/stm32f767nucleo/board.mk new file mode 100644 index 000000000..2400a4ba7 --- /dev/null +++ b/hw/bsp/stm32f7/boards/stm32f767nucleo/board.mk @@ -0,0 +1,12 @@ +PORT ?= 0 +SPEED ?= full + +CFLAGS += \ + -DSTM32F767xx \ + -DHSE_VALUE=8000000 \ + +LD_FILE = $(BOARD_PATH)/STM32F767ZITx_FLASH.ld +SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f767xx.s + +# flash target using on-board stlink +flash: flash-stlink diff --git a/hw/bsp/stm32f767nucleo/stm32f7xx_hal_conf.h b/hw/bsp/stm32f7/boards/stm32f767nucleo/stm32f7xx_hal_conf.h similarity index 100% rename from hw/bsp/stm32f767nucleo/stm32f7xx_hal_conf.h rename to hw/bsp/stm32f7/boards/stm32f767nucleo/stm32f7xx_hal_conf.h diff --git a/hw/bsp/stm32f7/family.c b/hw/bsp/stm32f7/family.c index eeedd2a66..548f45f5a 100644 --- a/hw/bsp/stm32f7/family.c +++ b/hw/bsp/stm32f7/family.c @@ -1,7 +1,8 @@ /* * The MIT License (MIT) * - * Copyright (c) 2020 Uwe Bonnes (bon@elektron.ikp.physik.tu-darmstadt.de), + * Copyright (c) 2019 William D. Jones (thor0505@comcast.net), + * Uwe Bonnes (bon@elektron.ikp.physik.tu-darmstadt.de), * Ha Thach (tinyusb.org) * * Permission is hereby granted, free of charge, to any person obtaining a copy @@ -25,9 +26,9 @@ * This file is part of the TinyUSB stack. */ -#include "../board.h" - #include "stm32f7xx_hal.h" +#include "bsp/board.h" +#include "board.h" //--------------------------------------------------------------------+ // Forward USB interrupt events to TinyUSB IRQ Handler @@ -44,104 +45,22 @@ void OTG_HS_IRQHandler(void) tud_int_handler(1); } - //--------------------------------------------------------------------+ // MACRO TYPEDEF CONSTANT ENUM //--------------------------------------------------------------------+ -#define LED_PORT GPIOB -#define LED_PIN GPIO_PIN_1 -#define LED_STATE_ON 1 - -#define BUTTON_PORT GPIOA -#define BUTTON_PIN GPIO_PIN_0 -#define BUTTON_STATE_ACTIVE 1 - -#define UARTx USART6 -#define UART_GPIO_PORT GPIOC -#define UART_GPIO_AF GPIO_AF8_USART6 -#define UART_TX_PIN GPIO_PIN_6 -#define UART_RX_PIN GPIO_PIN_7 - UART_HandleTypeDef UartHandle; -// enable all LED, Button, Uart, USB clock -static void all_rcc_clk_enable(void) -{ - __HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D- - __HAL_RCC_GPIOB_CLK_ENABLE(); // LED, OTG_HS - __HAL_RCC_GPIOC_CLK_ENABLE(); // Button - __HAL_RCC_GPIOD_CLK_ENABLE(); // Uart tx, rx - __HAL_RCC_USART6_CLK_ENABLE(); // Uart module -} - -/** - * @brief System Clock Configuration - * The system Clock is configured as follow : - * System Clock source = PLL (HSE) - * SYSCLK(Hz) = 216000000 - * HCLK(Hz) = 216000000 - * AHB Prescaler = 1 - * APB1 Prescaler = 4 - * APB2 Prescaler = 2 - * HSE Frequency(Hz) = 25000000 - * PLL_M = HSE_VALUE/1000000 - * PLL_N = 432 - * PLL_P = 2 - * PLL_Q = 9 - * VDD(V) = 3.3 - * Main regulator output voltage = Scale1 mode - * Flash Latency(WS) = 7 - * The USB clock configuration from PLLSAI: - * PLLSAIP = 8 - * PLLSAIN = 384 - * PLLSAIQ = 7 - * @param None - * @retval None - */ -void SystemClock_Config(void) -{ - RCC_ClkInitTypeDef RCC_ClkInitStruct; - RCC_OscInitTypeDef RCC_OscInitStruct; - - /* Enable Power Control clock */ - __HAL_RCC_PWR_CLK_ENABLE(); - - /* The voltage scaling allows optimizing the power consumption when the device is - clocked below the maximum system frequency, to update the voltage scaling value - regarding system frequency refer to product datasheet. */ - __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); - - /* Enable HSE Oscillator and activate PLL with HSE as source */ - RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; - RCC_OscInitStruct.HSEState = RCC_HSE_ON; - RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; - RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; - RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000; - RCC_OscInitStruct.PLL.PLLN = 432; - RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; - RCC_OscInitStruct.PLL.PLLQ = 9; - HAL_RCC_OscConfig(&RCC_OscInitStruct); - - /* Activate the OverDrive to reach the 216 MHz Frequency */ - HAL_PWREx_EnableOverDrive(); - - /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */ - RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); - RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; - RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; - RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; - RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; - - HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7); -} - void board_init(void) { + board_clock_init(); - - SystemClock_Config(); - all_rcc_clk_enable(); + // Enable peripherals clocks + __HAL_RCC_GPIOA_CLK_ENABLE(); + __HAL_RCC_GPIOB_CLK_ENABLE(); + __HAL_RCC_GPIOC_CLK_ENABLE(); + __HAL_RCC_GPIOD_CLK_ENABLE(); + UART_CLK_EN(); #if CFG_TUSB_OS == OPT_OS_NONE // 1ms tick timer @@ -172,7 +91,7 @@ void board_init(void) GPIO_InitStruct.Alternate = UART_GPIO_AF; HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct); - UartHandle.Instance = UARTx; + UartHandle.Instance = UART_DEV; UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; UartHandle.Init.WordLength = UART_WORDLENGTH_8B; UartHandle.Init.StopBits = UART_STOPBITS_1; diff --git a/hw/bsp/stm32f767nucleo/board.mk b/hw/bsp/stm32f767nucleo/board.mk deleted file mode 100644 index 9a6bada05..000000000 --- a/hw/bsp/stm32f767nucleo/board.mk +++ /dev/null @@ -1,49 +0,0 @@ -CFLAGS += \ - -flto \ - -mthumb \ - -mabi=aapcs \ - -mcpu=cortex-m7 \ - -mfloat-abi=hard \ - -mfpu=fpv5-d16 \ - -nostdlib -nostartfiles \ - -DSTM32F767xx \ - -DCFG_TUSB_MCU=OPT_MCU_STM32F7 - -# suppress warning caused by vendor mcu driver -CFLAGS += -Wno-error=cast-align -Wno-error=shadow - -ST_FAMILY = f7 -ST_CMSIS = hw/mcu/st/cmsis_device_$(ST_FAMILY) -ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver - -# All source paths should be relative to the top level. -LD_FILE = hw/bsp/$(BOARD)/STM32F767ZITx_FLASH.ld - -SRC_C += \ - $(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_uart.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_pwr_ex.c - -SRC_S += \ - $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f767xx.s - -INC += \ - $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \ - $(TOP)/$(ST_CMSIS)/Include \ - $(TOP)/$(ST_HAL_DRIVER)/Inc \ - $(TOP)/hw/bsp/$(BOARD) - -# For TinyUSB port source -VENDOR = st -CHIP_FAMILY = synopsys - -# For freeRTOS port source -FREERTOS_PORT = ARM_CM7/r0p1 - -# flash target using on-board stlink -flash: flash-stlink diff --git a/hw/bsp/stm32f767nucleo/stm32f767nucleo.c b/hw/bsp/stm32f767nucleo/stm32f767nucleo.c deleted file mode 100644 index 8328c361a..000000000 --- a/hw/bsp/stm32f767nucleo/stm32f767nucleo.c +++ /dev/null @@ -1,257 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2019 William D. Jones (thor0505@comcast.net), - * Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "../board.h" - -#include "stm32f7xx_hal.h" - -//--------------------------------------------------------------------+ -// Forward USB interrupt events to TinyUSB IRQ Handler -//--------------------------------------------------------------------+ -void OTG_FS_IRQHandler(void) -{ - tud_int_handler(0); -} - -//--------------------------------------------------------------------+ -// MACRO TYPEDEF CONSTANT ENUM -//--------------------------------------------------------------------+ - -#define LED_PORT GPIOB -#define LED_PIN GPIO_PIN_14 -#define LED_STATE_ON 1 - -#define BUTTON_PORT GPIOC -#define BUTTON_PIN GPIO_PIN_13 -#define BUTTON_STATE_ACTIVE 1 - -#define UARTx USART3 -#define UART_GPIO_PORT GPIOD -#define UART_GPIO_AF GPIO_AF7_USART3 -#define UART_TX_PIN GPIO_PIN_8 -#define UART_RX_PIN GPIO_PIN_9 - -UART_HandleTypeDef UartHandle; - -// enable all LED, Button, Uart, USB clock -static void all_rcc_clk_enable(void) -{ - __HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D- - __HAL_RCC_GPIOB_CLK_ENABLE(); // LED - __HAL_RCC_GPIOC_CLK_ENABLE(); // Button - __HAL_RCC_GPIOD_CLK_ENABLE(); // Uart tx, rx - __HAL_RCC_USART3_CLK_ENABLE(); // Uart module -} - -/** - * @brief System Clock Configuration - * The system Clock is configured as follow : - * System Clock source = PLL (HSE) - * SYSCLK(Hz) = 216000000 - * HCLK(Hz) = 216000000 - * AHB Prescaler = 1 - * APB1 Prescaler = 4 - * APB2 Prescaler = 2 - * HSE Frequency(Hz) = 8000000 - * PLL_M = HSE_VALUE/1000000 - * PLL_N = 432 - * PLL_P = 2 - * PLL_Q = 9 - * PLL_R = 7 - * VDD(V) = 3.3 - * Main regulator output voltage = Scale1 mode - * Flash Latency(WS) = 7 - * The USB clock configuration from PLLSAI: - * PLLSAIP = 8 - * PLLSAIN = 384 - * PLLSAIQ = 7 - * @param None - * @retval None - */ -void SystemClock_Config(void) -{ - RCC_ClkInitTypeDef RCC_ClkInitStruct; - RCC_OscInitTypeDef RCC_OscInitStruct; - - /* Enable Power Control clock */ - __HAL_RCC_PWR_CLK_ENABLE(); - - /* The voltage scaling allows optimizing the power consumption when the device is - clocked below the maximum system frequency, to update the voltage scaling value - regarding system frequency refer to product datasheet. */ - __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); - - /* Enable HSE Oscillator and activate PLL with HSE as source */ - RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; - RCC_OscInitStruct.HSEState = RCC_HSE_ON; - RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; - RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; - RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000; - RCC_OscInitStruct.PLL.PLLN = 432; - RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; - RCC_OscInitStruct.PLL.PLLQ = 9; - RCC_OscInitStruct.PLL.PLLR = 7; - HAL_RCC_OscConfig(&RCC_OscInitStruct); - - /* Activate the OverDrive to reach the 216 MHz Frequency */ - HAL_PWREx_EnableOverDrive(); - - /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */ - RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); - RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; - RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; - RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; - RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; - - HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7); -} - -void board_init(void) -{ - - - SystemClock_Config(); - all_rcc_clk_enable(); - -#if CFG_TUSB_OS == OPT_OS_NONE - // 1ms tick timer - SysTick_Config(SystemCoreClock / 1000); -#endif - - GPIO_InitTypeDef GPIO_InitStruct; - - // LED - GPIO_InitStruct.Pin = LED_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; - GPIO_InitStruct.Pull = GPIO_PULLUP; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); - - // Button - GPIO_InitStruct.Pin = BUTTON_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_INPUT; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); - - // Uart - GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_PULLUP; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; - GPIO_InitStruct.Alternate = UART_GPIO_AF; - HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct); - - UartHandle.Instance = UARTx; - UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; - UartHandle.Init.WordLength = UART_WORDLENGTH_8B; - UartHandle.Init.StopBits = UART_STOPBITS_1; - UartHandle.Init.Parity = UART_PARITY_NONE; - UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE; - UartHandle.Init.Mode = UART_MODE_TX_RX; - UartHandle.Init.OverSampling = UART_OVERSAMPLING_16; - HAL_UART_Init(&UartHandle); - - /* Configure USB FS GPIOs */ - /* Configure DM DP Pins */ - GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12); - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_HIGH; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - /* Configure VBUS Pin */ - GPIO_InitStruct.Pin = GPIO_PIN_9; - GPIO_InitStruct.Mode = GPIO_MODE_INPUT; - GPIO_InitStruct.Pull = GPIO_NOPULL; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - /* Configure ID pin */ - GPIO_InitStruct.Pin = GPIO_PIN_10; - GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; - GPIO_InitStruct.Pull = GPIO_PULLUP; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - /* Enable USB FS Clocks */ - __HAL_RCC_USB_OTG_FS_CLK_ENABLE(); - - // Enable VBUS sense (B device) via pin PA9 - USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN; -} - -//--------------------------------------------------------------------+ -// Board porting API -//--------------------------------------------------------------------+ - -void board_led_write(bool state) -{ - HAL_GPIO_WritePin(LED_PORT, LED_PIN, state); -} - -uint32_t board_button_read(void) -{ - return HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN); -} - -int board_uart_read(uint8_t* buf, int len) -{ - (void) buf; (void) len; - return 0; -} - -int board_uart_write(void const * buf, int len) -{ - HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff); - return len; -} - -#if CFG_TUSB_OS == OPT_OS_NONE -volatile uint32_t system_ticks = 0; -void SysTick_Handler (void) -{ - system_ticks++; -} - -uint32_t board_millis(void) -{ - return system_ticks; -} -#endif - -void HardFault_Handler (void) -{ - asm("bkpt"); -} - -// Required by __libc_init_array in startup code if we are compiling using -// -nostdlib/-nostartfiles. -void _init(void) -{ - -}