diff --git a/hw/bsp/stm32f070rbnucleo/board.mk b/hw/bsp/stm32f070rbnucleo/board.mk
new file mode 100644
index 000000000..5206a6f91
--- /dev/null
+++ b/hw/bsp/stm32f070rbnucleo/board.mk
@@ -0,0 +1,50 @@
+CFLAGS += \
+ -DHSE_VALUE=8000000 \
+ -DSTM32F070xB \
+ -mthumb \
+ -mabi=aapcs-linux \
+ -mcpu=cortex-m4 \
+ -mfloat-abi=soft \
+ -nostdlib -nostartfiles \
+ -DCFG_TUSB_MCU=OPT_MCU_STM32_FSDEV
+
+ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F0xx_HAL_Driver
+ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F0xx
+
+# All source paths should be relative to the top level.
+LD_FILE = hw/bsp/stm32f070rbnucleo/stm32F070rbtx_flash.ld
+
+SRC_C += \
+ $(ST_CMSIS)/Source/Templates/system_stm32f0xx.c \
+ $(ST_HAL_DRIVER)/Src/stm32f0xx_hal.c \
+ $(ST_HAL_DRIVER)/Src/stm32f0xx_hal_cortex.c \
+ $(ST_HAL_DRIVER)/Src/stm32f0xx_hal_rcc.c \
+ $(ST_HAL_DRIVER)/Src/stm32f0xx_hal_rcc_ex.c \
+ $(ST_HAL_DRIVER)/Src/stm32f0xx_hal_gpio.c
+
+SRC_S += \
+ $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f070xb.s
+
+INC += \
+ $(TOP)/hw/mcu/st/st_driver/CMSIS/Include \
+ $(TOP)/$(ST_CMSIS)/Include \
+ $(TOP)/$(ST_HAL_DRIVER)/Inc \
+ $(TOP)/hw/bsp/$(BOARD)
+
+# For TinyUSB port source
+VENDOR = st
+CHIP_FAMILY = stm32_fsdev
+
+# For freeRTOS port source
+FREERTOS_PORT = ARM_CM4F
+
+# For flash-jlink target
+JLINK_DEVICE = stm32f303vc
+JLINK_IF = swd
+
+# Path to STM32 Cube Programmer CLI, should be added into system path
+STM32Prog = STM32_Programmer_CLI
+
+# flash target using on-board stlink
+flash: $(BUILD)/$(BOARD)-firmware.elf
+ $(STM32Prog) --connect port=swd --write $< --go
diff --git a/hw/bsp/stm32f070rbnucleo/stm32F070rbtx_flash.ld b/hw/bsp/stm32f070rbnucleo/stm32F070rbtx_flash.ld
new file mode 100644
index 000000000..7ae8e5960
--- /dev/null
+++ b/hw/bsp/stm32f070rbnucleo/stm32F070rbtx_flash.ld
@@ -0,0 +1,200 @@
+/*
+******************************************************************************
+**
+** File : LinkerScript.ld
+**
+** Author : Auto-generated by STM32CubeIDE
+**
+** Abstract : Linker script for STM32F070RBTx Device from STM32F0 series
+** 128Kbytes FLASH
+** 16Kbytes RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+** Distribution: The file is distributed as is without any warranty
+** of any kind.
+**
+*****************************************************************************
+** @attention
+**
+**
© COPYRIGHT(c) 2019 STMicroelectronics
+**
+** Redistribution and use in source and binary forms, with or without modification,
+** are permitted provided that the following conditions are met:
+** 1. Redistributions of source code must retain the above copyright notice,
+** this list of conditions and the following disclaimer.
+** 2. Redistributions in binary form must reproduce the above copyright notice,
+** this list of conditions and the following disclaimer in the documentation
+** and/or other materials provided with the distribution.
+** 3. Neither the name of STMicroelectronics nor the names of its contributors
+** may be used to endorse or promote products derived from this software
+** without specific prior written permission.
+**
+** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = 0x20004000; /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x400; /* required amount of heap */
+_Min_Stack_Size = 0x600; /* required amount of stack */
+
+/* Memories definition */
+MEMORY
+{
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 16K
+ FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 128K
+}
+
+/* Sections */
+SECTIONS
+{
+ /* The startup code into "FLASH" Rom type memory */
+ .isr_vector :
+ {
+ . = ALIGN(4);
+ KEEP(*(.isr_vector)) /* Startup code */
+ . = ALIGN(4);
+ } >FLASH
+
+ /* The program code and other data into "FLASH" Rom type memory */
+ .text :
+ {
+ . = ALIGN(4);
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ . = ALIGN(4);
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data into "FLASH" Rom type memory */
+ .rodata :
+ {
+ . = ALIGN(4);
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM.extab : {
+ . = ALIGN(4);
+ *(.ARM.extab* .gnu.linkonce.armextab.*)
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM : {
+ . = ALIGN(4);
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ . = ALIGN(4);
+ } >FLASH
+
+ .preinit_array :
+ {
+ . = ALIGN(4);
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ . = ALIGN(4);
+ } >FLASH
+
+ .init_array :
+ {
+ . = ALIGN(4);
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ . = ALIGN(4);
+ } >FLASH
+
+ .fini_array :
+ {
+ . = ALIGN(4);
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ . = ALIGN(4);
+ } >FLASH
+
+ /* Used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections into "RAM" Ram type memory */
+ .data :
+ {
+ . = ALIGN(4);
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+
+ . = ALIGN(4);
+ _edata = .; /* define a global symbol at data end */
+
+ } >RAM AT> FLASH
+
+ /* Uninitialized data section into "RAM" Ram type memory */
+ . = ALIGN(4);
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss secion */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ . = ALIGN(4);
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+ /* Remove information from the compiler libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32f070rbnucleo/stm32f070rbnucleo.c b/hw/bsp/stm32f070rbnucleo/stm32f070rbnucleo.c
new file mode 100644
index 000000000..8f864f739
--- /dev/null
+++ b/hw/bsp/stm32f070rbnucleo/stm32f070rbnucleo.c
@@ -0,0 +1,150 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2019 Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#include "../board.h"
+
+#include "stm32f0xx.h"
+#include "stm32f0xx_hal_conf.h"
+
+#define LED_PORT GPIOC
+#define LED_PIN GPIO_PIN_13
+#define LED_STATE_ON 1
+
+#define BUTTON_PORT GPIOA
+#define BUTTON_PIN GPIO_PIN_5
+#define BUTTON_STATE_ACTIVE 1
+
+void board_init(void)
+{
+ #if CFG_TUSB_OS == OPT_OS_NONE
+ // 1ms tick timer
+ SysTick_Config(SystemCoreClock / 1000);
+ #endif
+
+ /* Configure the system clock to 48 MHz */
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};
+
+ /* Enable HSE Oscillator and activate PLL with 8 MHz HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL6;
+ RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV1;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2
+ clocks dividers */
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
+ (void) HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1);
+
+
+ PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USB;
+ PeriphClkInit.UsbClockSelection = RCC_USBCLKSOURCE_PLL;
+ (void)HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) ;
+
+ // Notify runtime of frequency change.
+ SystemCoreClockUpdate();
+
+ // LED
+ __HAL_RCC_GPIOC_CLK_ENABLE();
+ GPIO_InitTypeDef GPIO_InitStruct;
+ GPIO_InitStruct.Pin = LED_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
+
+ // Button
+ __HAL_RCC_GPIOA_CLK_ENABLE();
+ GPIO_InitStruct.Pin = BUTTON_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+ GPIO_InitStruct.Pull = GPIO_PULLDOWN;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct);
+
+}
+
+//--------------------------------------------------------------------+
+// Board porting API
+//--------------------------------------------------------------------+
+
+void board_led_write(bool state)
+{
+ HAL_GPIO_WritePin(LED_PORT, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON));
+}
+
+uint32_t board_button_read(void)
+{
+ return BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN);
+}
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+volatile uint32_t system_ticks = 0;
+void SysTick_Handler (void)
+{
+ system_ticks++;
+}
+
+uint32_t board_millis(void)
+{
+ return system_ticks;
+}
+#endif
+
+void HardFault_Handler (void)
+{
+ asm("bkpt");
+}
+
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief Reports the name of the source file and the source line number
+ * where the assert_param error has occurred.
+ * @param file: pointer to the source file name
+ * @param line: assert_param error line source number
+ * @retval None
+ */
+void assert_failed(char *file, uint32_t line)
+{
+ /* USER CODE BEGIN 6 */
+ /* User can add his own implementation to report the file name and line number,
+ tex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
+ /* USER CODE END 6 */
+}
+#endif /* USE_FULL_ASSERT */
+
+// Required by __libc_init_array in startup code if we are compiling using
+// -nostdlib/-nostartfiles.
+void _init(void)
+{
+
+}
diff --git a/hw/bsp/stm32f070rbnucleo/stm32f0xx_hal_conf.h b/hw/bsp/stm32f070rbnucleo/stm32f0xx_hal_conf.h
new file mode 100644
index 000000000..7e3721afc
--- /dev/null
+++ b/hw/bsp/stm32f070rbnucleo/stm32f0xx_hal_conf.h
@@ -0,0 +1,324 @@
+/**
+ ******************************************************************************
+ * @file GPIO/GPIO_IOToggle/Inc/stm32f3xx_hal_conf.h
+ * @author MCD Application Team
+ * @brief HAL configuration file.
+ ******************************************************************************
+ * @attention
+ *
+ * © COPYRIGHT(c) 2016 STMicroelectronics
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_CONF_H
+#define __STM32F0xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+ * @brief This is the list of modules to be used in the HAL driver
+ */
+#define HAL_MODULE_ENABLED
+/*#define HAL_ADC_MODULE_ENABLED */
+/*#define HAL_CRYP_MODULE_ENABLED */
+/*#define HAL_CAN_MODULE_ENABLED */
+/*#define HAL_CEC_MODULE_ENABLED */
+/*#define HAL_COMP_MODULE_ENABLED */
+/*#define HAL_CRC_MODULE_ENABLED */
+/*#define HAL_CRYP_MODULE_ENABLED */
+/*#define HAL_TSC_MODULE_ENABLED */
+/*#define HAL_DAC_MODULE_ENABLED */
+/*#define HAL_I2S_MODULE_ENABLED */
+/*#define HAL_IWDG_MODULE_ENABLED */
+/*#define HAL_LCD_MODULE_ENABLED */
+/*#define HAL_LPTIM_MODULE_ENABLED */
+/*#define HAL_RNG_MODULE_ENABLED */
+/*#define HAL_RTC_MODULE_ENABLED */
+/*#define HAL_SPI_MODULE_ENABLED */
+/*#define HAL_TIM_MODULE_ENABLED */
+/*#define HAL_UART_MODULE_ENABLED */
+#define HAL_USART_MODULE_ENABLED
+/*#define HAL_IRDA_MODULE_ENABLED */
+/*#define HAL_SMARTCARD_MODULE_ENABLED */
+/*#define HAL_SMBUS_MODULE_ENABLED */
+/*#define HAL_WWDG_MODULE_ENABLED */
+#define HAL_PCD_MODULE_ENABLED
+/*#define HAL_EXTI_MODULE_ENABLED */
+#define HAL_CORTEX_MODULE_ENABLED
+#define HAL_DMA_MODULE_ENABLED
+#define HAL_FLASH_MODULE_ENABLED
+#define HAL_GPIO_MODULE_ENABLED
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+#define HAL_I2C_MODULE_ENABLED
+
+/* ########################## HSE/HSI Values adaptation ##################### */
+/**
+ * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSE is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+/**
+ * @brief In the following line adjust the External High Speed oscillator (HSE) Startup
+ * Timeout value
+ */
+#if !defined (HSE_STARTUP_TIMEOUT)
+ #define HSE_STARTUP_TIMEOUT ((uint32_t)100) /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator (HSI) value.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSI is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE ((uint32_t)8000000) /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+ * @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup
+ * Timeout value
+ */
+#if !defined (HSI_STARTUP_TIMEOUT)
+ #define HSI_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSI start up */
+#endif /* HSI_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator for ADC (HSI14) value.
+ */
+#if !defined (HSI14_VALUE)
+#define HSI14_VALUE ((uint32_t)14000000) /*!< Value of the Internal High Speed oscillator for ADC in Hz.
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+#endif /* HSI14_VALUE */
+
+/**
+ * @brief Internal High Speed oscillator for USB (HSI48) value.
+ */
+#if !defined (HSI48_VALUE)
+#define HSI48_VALUE ((uint32_t)48000000) /*!< Value of the Internal High Speed oscillator for USB in Hz.
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+#endif /* HSI48_VALUE */
+
+/**
+ * @brief Internal Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSI_VALUE)
+ #define LSI_VALUE ((uint32_t)40000)
+#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+/**
+ * @brief External Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSE_VALUE)
+ #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+#if !defined (LSE_STARTUP_TIMEOUT)
+ #define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+ === you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+ * @brief This is the HAL system configuration section
+ */
+#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY ((uint32_t)0) /*!< tick interrupt priority (lowest by default) */
+ /* Warning: Must be set to higher priority for HAL_Delay() */
+ /* and HAL_GetTick() usage under interrupt context */
+#define USE_RTOS 0
+#define PREFETCH_ENABLE 1
+#define INSTRUCTION_CACHE_ENABLE 0
+#define DATA_CACHE_ENABLE 0
+/* ########################## Assert Selection ############################## */
+/**
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * HAL drivers code
+ */
+ #define USE_FULL_ASSERT 1U
+
+/* ################## SPI peripheral configuration ########################## */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+* Activated: CRC code is present inside driver
+* Deactivated: CRC code cleaned from driver
+*/
+
+#define USE_SPI_CRC 0U
+
+/* Includes ------------------------------------------------------------------*/
+/**
+ * @brief Include module's header file
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32f0xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_EXTI_MODULE_ENABLED
+ #include "stm32f0xx_hal_exti.h"
+#endif /* HAL_EXTI_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32f0xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+ #include "stm32f0xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32f0xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32f0xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32f0xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CEC_MODULE_ENABLED
+ #include "stm32f0xx_hal_cec.h"
+#endif /* HAL_CEC_MODULE_ENABLED */
+
+#ifdef HAL_COMP_MODULE_ENABLED
+ #include "stm32f0xx_hal_comp.h"
+#endif /* HAL_COMP_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32f0xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32f0xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32f0xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f0xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f0xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f0xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f0xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f0xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f0xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f0xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f0xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_SMBUS_MODULE_ENABLED
+ #include "stm32f0xx_hal_smbus.h"
+#endif /* HAL_SMBUS_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f0xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f0xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_TSC_MODULE_ENABLED
+ #include "stm32f0xx_hal_tsc.h"
+#endif /* HAL_TSC_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f0xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f0xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f0xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr: If expr is false, it calls assert_failed function
+ * which reports the name of the source file and the source
+ * line number of the call that failed.
+ * If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0U : assert_failed((char *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(char* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F0xx_HAL_CONF_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/hw/bsp/stm32f303disco/board.mk b/hw/bsp/stm32f303disco/board.mk
index d1421f26d..718ff27a3 100644
--- a/hw/bsp/stm32f303disco/board.mk
+++ b/hw/bsp/stm32f303disco/board.mk
@@ -7,7 +7,7 @@ CFLAGS += \
-mfloat-abi=hard \
-mfpu=fpv4-sp-d16 \
-nostdlib -nostartfiles \
- -DCFG_TUSB_MCU=OPT_MCU_STM32F3
+ -DCFG_TUSB_MCU=OPT_MCU_STM32_FSDEV
ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F3xx_HAL_Driver
ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F3xx
@@ -33,7 +33,7 @@ INC += \
# For TinyUSB port source
VENDOR = st
-CHIP_FAMILY = stm32f3
+CHIP_FAMILY = stm32_fsdev
# For freeRTOS port source
FREERTOS_PORT = ARM_CM4F
diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c
index 170a291e3..2411c1c37 100644
--- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c
+++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c
@@ -99,9 +99,7 @@
#undef USE_HAL_DRIVER
#include "device/dcd.h"
-#include "stm32f0xx.h"
#include "portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h"
-#include "uart_util.h"
/*****************************************************
@@ -120,7 +118,7 @@
#endif
#ifndef DCD_STM32_BTABLE_LENGTH
-# define DCD_STM32_BTABLE_LENGTH (DCD_STM32_BTABLE_LENGTH - DCD_STM32_BTABLE_BASE)
+# define DCD_STM32_BTABLE_LENGTH (PMA_LENGTH - DCD_STM32_BTABLE_BASE)
#endif
/***************************************************
@@ -131,7 +129,7 @@
# error Only 8 endpoints supported on the hardware
#endif
-#if ((BTABLE_BASE + BTABLE_LENGTH)>PMA_LENGTH)
+#if ((DCD_STM32_BTABLE_BASE + DCD_STM32_BTABLE_LENGTH)>PMA_LENGTH)
# error BTABLE does not fit in PMA RAM
#endif
@@ -157,10 +155,11 @@ static uint8_t newDADDR; // Used to set the new device address during the CTR IR
// EP Buffers assigned from end of memory location, to minimize their chance of crashing
// into the stack.
static uint16_t ep_buf_ptr;
-static void dcd_handle_bus_reset();
+static void dcd_handle_bus_reset(void);
static void dcd_write_packet_memory(uint16_t dst, const void *__restrict src, size_t wNBytes);
static void dcd_read_packet_memory(void *__restrict dst, uint16_t src, size_t wNBytes);
static void dcd_transmit_packet(xfer_ctl_t * xfer, uint16_t ep_ix);
+static uint16_t dcd_ep_ctr_handler(void);
void dcd_init (uint8_t rhport)
{
@@ -218,15 +217,35 @@ void dcd_init (uint8_t rhport)
void dcd_int_enable (uint8_t rhport)
{
(void)rhport;
+#if defined(STM32F0)
NVIC_SetPriority(USB_IRQn, 0);
NVIC_EnableIRQ(USB_IRQn);
+#elif defined(STM32F3)
+#warning need to check these since the F3 can have its USB interrupts remapped.
+ NVIC_SetPriority(USB_HP_CAN_TX_IRQn, 0);
+ NVIC_SetPriority(USB_LP_CAN_RX0_IRQn, 0);
+ NVIC_SetPriority(USBWakeUp_IRQn, 0);
+ NVIC_EnableIRQ(USB_HP_CAN_TX_IRQn);
+ NVIC_EnableIRQ(USB_LP_CAN_RX0_IRQn);
+ NVIC_EnableIRQ(USBWakeUp_IRQn);
+
+#endif
}
// Disable device interrupt
void dcd_int_disable(uint8_t rhport)
{
(void)rhport;
+#if defined(STM32F0)
NVIC_DisableIRQ(USB_IRQn);
+#elif defined(STM32F3)
+#warning need to check these since the F3 can have its USB interrupts remapped.
+ NVIC_DisableIRQ(USB_HP_CAN_TX_IRQn);
+ NVIC_DisableIRQ(USB_LP_CAN_RX0_IRQn);
+ NVIC_DisableIRQ(USBWakeUp_IRQn);
+#else
+#error Unknown arch in USB driver
+#endif
}
// Receive Set Address request, mcu port must also include status IN response
@@ -277,7 +296,7 @@ static const tusb_desc_endpoint_t ep0IN_desc =
#pragma GCC diagnostic pop
-static void dcd_handle_bus_reset()
+static void dcd_handle_bus_reset(void)
{
//__IO uint16_t * const epreg = &(EPREG(0));
USB->DADDR = 0u; // disable USB peripheral by clearing the EF flag
@@ -297,7 +316,7 @@ static void dcd_handle_bus_reset()
}
// FIXME: Defined to return uint16 so that ASSERT can be used, even though a return value is not needed.
-static uint16_t dcd_ep_ctr_handler()
+static uint16_t dcd_ep_ctr_handler(void)
{
uint16_t count=0U;
uint8_t EPindex;
diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h
index 030635b8b..a6fccfd53 100644
--- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h
+++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h
@@ -35,6 +35,21 @@
// This file contains source copied from ST's HAL, and thus should have their copyright statement.
+// PMA_LENGTH is PMA buffer size in bytes.
+
+#if defined(STM32F070xB) | defined(STM32F070x6)
+#include "stm32f0xx.h"
+#define PMA_LENGTH 1024
+#elif defined(STM32F303xB) | defined(STM32F303xC)
+#warning STM32F3 platform is untested.
+#include "stm32f3xx.h"
+#define PMA_LENGTH 512
+#else
+#error You are using an untested or unimplemented STM32 variant
+#endif
+
+
+
#ifndef PORTABLE_ST_STM32F0_DCD_STM32F0_FSDEV_PVT_ST_H_
#define PORTABLE_ST_STM32F0_DCD_STM32F0_FSDEV_PVT_ST_H_
@@ -217,16 +232,14 @@
#define EPREG(n) (((__IO uint16_t*)USB_BASE)[n*2])
-#define USB_ISTR_ALL_EVENTS (USB_ISTR_PMAOVR | USB_ISTR_ERR | USB_ISTR_WKUP | USB_ISTR_SUSP | \
- USB_ISTR_RESET | USB_ISTR_SOF | USB_ISTR_ESOF | USB_ISTR_L1REQ )
-
-
-// PMA_LENGTH is PMA buffer size in bytes.
-
-#if defined(STM32F070xB) | defined(STM32F070x6)
-#define PMA_LENGTH 1024
+#if defined(USB_ISTR_L1REQ)
+#define USB_ISTR_L1REQ_FORCED USB_ISTR_L1REQ
#else
-#error You are using an untested or unimplemented STM32 variant
+#define USB_ISTR_L1REQ_FORCED ((uint16_t)0x0000U)
#endif
+#define USB_ISTR_ALL_EVENTS (USB_ISTR_PMAOVR | USB_ISTR_ERR | USB_ISTR_WKUP | USB_ISTR_SUSP | \
+ USB_ISTR_RESET | USB_ISTR_SOF | USB_ISTR_ESOF | USB_ISTR_L1REQ_FORCED )
+
+
#endif /* PORTABLE_ST_STM32F0_DCD_STM32F0_FSDEV_PVT_ST_H_ */