diff --git a/README.md b/README.md index 7e998f248..732fcb26d 100644 --- a/README.md +++ b/README.md @@ -55,7 +55,7 @@ The stack supports the following MCUs - **Nordic:** nRF52840 - **NXP:** LPC11Uxx, LPC13xx, LPC175x_6x, LPC177x_8x, LPC18xx, LPC40xx, LPC43xx, LPC51Uxx - **MicroChip:** SAMD21, SAMD51 (device only) -- **ST:** STM32F070xB, STM32F4, STM32H7 (device only) +- **ST:** STM32F0, STM32F4, STM32H7 (device only) [Here is the list of supported Boards](docs/boards.md) diff --git a/docs/boards.md b/docs/boards.md index 56410ee4d..410104e54 100644 --- a/docs/boards.md +++ b/docs/boards.md @@ -41,6 +41,7 @@ This code base already had supported for a handful of following boards ### ST STM32 - [STM32F070RB Nucleo](https://www.st.com/en/evaluation-tools/nucleo-f070rb.html) +- [STM32F072b Discovery](https://www.st.com/en/evaluation-tools/32f072bdiscovery.html) - [STM32F407g Discovery](https://www.st.com/en/evaluation-tools/stm32f4discovery.html) - [STM32F411e Discovery](https://www.st.com/en/evaluation-tools/32f411ediscovery.html) - [STM32F412g Discovery](https://www.st.com/en/evaluation-tools/32f412gdiscovery.html) diff --git a/examples/device/cdc_msc_hid/src/msc_disk.c b/examples/device/cdc_msc_hid/src/msc_disk.c index bc61f5d67..5aa7befc9 100644 --- a/examples/device/cdc_msc_hid/src/msc_disk.c +++ b/examples/device/cdc_msc_hid/src/msc_disk.c @@ -29,11 +29,8 @@ #if CFG_TUD_MSC // Some MCU doesn't have enough 8KB SRAM to store the whole disk -// We will use Flash as read-only disk -// - LPC1347, LPC11uxx -#if (CFG_TUSB_MCU == OPT_MCU_LPC13XX) || (CFG_TUSB_MCU == OPT_MCU_LPC11UXX) -#define DISK_READONLY -#endif +// We will use Flash as read-only disk with board that has +// CFG_EXAMPLE_MSC_READONLY defined #define README_CONTENTS \ "This is tinyusb's MassStorage Class demo.\r\n\r\n\ @@ -46,7 +43,7 @@ enum DISK_BLOCK_SIZE = 512 }; -#ifdef DISK_READONLY +#ifdef CFG_EXAMPLE_MSC_READONLY const #endif uint8_t msc_disk[DISK_BLOCK_NUM][DISK_BLOCK_SIZE] = @@ -193,7 +190,7 @@ int32_t tud_msc_write10_cb(uint8_t lun, uint32_t lba, uint32_t offset, uint8_t* { (void) lun; -#ifndef DISK_READONLY +#ifndef CFG_EXAMPLE_MSC_READONLY uint8_t* addr = msc_disk[lba] + offset; memcpy(addr, buffer, bufsize); #else diff --git a/examples/device/cdc_msc_hid_freertos/src/msc_disk.c b/examples/device/cdc_msc_hid_freertos/src/msc_disk.c index 184602cdd..b4986fbb7 100644 --- a/examples/device/cdc_msc_hid_freertos/src/msc_disk.c +++ b/examples/device/cdc_msc_hid_freertos/src/msc_disk.c @@ -29,11 +29,8 @@ #if CFG_TUD_MSC // Some MCU doesn't have enough 8KB SRAM to store the whole disk -// We will use Flash as read-only disk -// - LPC1347, LPC11uxx -#if (CFG_TUSB_MCU == OPT_MCU_LPC13XX) || (CFG_TUSB_MCU == OPT_MCU_LPC11UXX) -#define DISK_READONLY -#endif +// We will use Flash as read-only disk with board that has +// CFG_EXAMPLE_MSC_READONLY defined #define README_CONTENTS \ "This is tinyusb's MassStorage Class demo.\r\n\r\n\ @@ -46,7 +43,7 @@ enum DISK_BLOCK_SIZE = 512 }; -#ifdef DISK_READONLY +#ifdef CFG_EXAMPLE_MSC_READONLY const #endif uint8_t msc_disk[DISK_BLOCK_NUM][DISK_BLOCK_SIZE] = @@ -193,7 +190,7 @@ int32_t tud_msc_write10_cb(uint8_t lun, uint32_t lba, uint32_t offset, uint8_t* { (void) lun; -#ifndef DISK_READONLY +#ifndef CFG_EXAMPLE_MSC_READONLY uint8_t* addr = msc_disk[lba] + offset; memcpy(addr, buffer, bufsize); #else diff --git a/examples/device/msc_dual_lun/src/msc_disk_dual.c b/examples/device/msc_dual_lun/src/msc_disk_dual.c index faa90ee7b..2ab050da8 100644 --- a/examples/device/msc_dual_lun/src/msc_disk_dual.c +++ b/examples/device/msc_dual_lun/src/msc_disk_dual.c @@ -29,11 +29,8 @@ #if CFG_TUD_MSC // Some MCU doesn't have enough 8KB SRAM to store the whole disk -// We will use Flash as read-only disk -// - LPC1347, LPC11uxx -#if (CFG_TUSB_MCU == OPT_MCU_LPC13XX) || (CFG_TUSB_MCU == OPT_MCU_LPC11UXX) || defined(STM32F070xB) -#define DISK_READONLY -#endif +// We will use Flash as read-only disk with board that has +// CFG_EXAMPLE_MSC_READONLY defined enum { @@ -51,7 +48,7 @@ If you find any bugs or get any questions, feel free to file an\r\n\ issue at github.com/hathach/tinyusb" -#ifdef DISK_READONLY +#ifdef CFG_EXAMPLE_MSC_READONLY const #endif uint8_t msc_disk0[DISK_BLOCK_NUM][DISK_BLOCK_SIZE] = @@ -132,7 +129,7 @@ uint8_t msc_disk0[DISK_BLOCK_NUM][DISK_BLOCK_SIZE] = If you find any bugs or get any questions, feel free to file an\r\n\ issue at github.com/hathach/tinyusb" -#ifdef DISK_READONLY +#ifdef CFG_EXAMPLE_MSC_READONLY const #endif uint8_t msc_disk1[DISK_BLOCK_NUM][DISK_BLOCK_SIZE] = @@ -281,7 +278,7 @@ int32_t tud_msc_read10_cb(uint8_t lun, uint32_t lba, uint32_t offset, void* buff // Process data in buffer to disk's storage and return number of written bytes int32_t tud_msc_write10_cb(uint8_t lun, uint32_t lba, uint32_t offset, uint8_t* buffer, uint32_t bufsize) { -#ifndef DISK_READONLY +#ifndef CFG_EXAMPLE_MSC_READONLY uint8_t* addr = (lun ? msc_disk1[lba] : msc_disk0[lba]) + offset; memcpy(addr, buffer, bufsize); #else diff --git a/hw/bsp/lpcxpresso11u37/board.mk b/hw/bsp/lpcxpresso11u37/board.mk index 2a7a9f74a..228765550 100644 --- a/hw/bsp/lpcxpresso11u37/board.mk +++ b/hw/bsp/lpcxpresso11u37/board.mk @@ -5,6 +5,7 @@ CFLAGS += \ -nostdlib \ -DCORE_M0 \ -D__USE_LPCOPEN \ + -DCFG_EXAMPLE_MSC_READONLY \ -DCFG_TUSB_MCU=OPT_MCU_LPC11UXX \ -DCFG_TUSB_MEM_SECTION='__attribute__((section(".data.$$RAM2")))' \ -DCFG_TUSB_MEM_ALIGN='__attribute__((aligned(64)))' diff --git a/hw/bsp/lpcxpresso1347/board.mk b/hw/bsp/lpcxpresso1347/board.mk index edae27c61..4e0c70392 100644 --- a/hw/bsp/lpcxpresso1347/board.mk +++ b/hw/bsp/lpcxpresso1347/board.mk @@ -5,6 +5,7 @@ CFLAGS += \ -nostdlib \ -DCORE_M3 \ -D__USE_LPCOPEN \ + -DCFG_EXAMPLE_MSC_READONLY \ -DCFG_TUSB_MCU=OPT_MCU_LPC13XX \ -DCFG_TUSB_MEM_SECTION='__attribute__((section(".data.$$RAM3")))' \ -DCFG_TUSB_MEM_ALIGN='__attribute__((aligned(64)))' diff --git a/hw/bsp/stm32f070rbnucleo/board.mk b/hw/bsp/stm32f070rbnucleo/board.mk index e4036982e..b53aac5bb 100644 --- a/hw/bsp/stm32f070rbnucleo/board.mk +++ b/hw/bsp/stm32f070rbnucleo/board.mk @@ -6,6 +6,7 @@ CFLAGS += \ -mcpu=cortex-m0 \ -mfloat-abi=soft \ -nostdlib -nostartfiles \ + -DCFG_EXAMPLE_MSC_READONLY \ -DCFG_TUSB_MCU=OPT_MCU_STM32F0 ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F0xx_HAL_Driver diff --git a/hw/bsp/stm32f072disco/STM32F072RBTx_FLASH.ld b/hw/bsp/stm32f072disco/STM32F072RBTx_FLASH.ld new file mode 100644 index 000000000..8d31f6a00 --- /dev/null +++ b/hw/bsp/stm32f072disco/STM32F072RBTx_FLASH.ld @@ -0,0 +1,169 @@ +/* +***************************************************************************** +** + +** File : LinkerScript.ld +** +** Abstract : Linker script for STM32F072RBTx Device with +** 128KByte FLASH, 16KByte RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +** (c)Copyright Ac6. +** You may use this file as-is or modify it according to the needs of your +** project. Distribution of this file (unmodified or modified) is not +** permitted. Ac6 permit registered System Workbench for MCU users the +** rights to distribute the assembled, compiled & linked contents of this +** file as part of an application binary file, provided that it is built +** using the System Workbench for MCU toolchain. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20004000; /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x400; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 128K +RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 16K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} + + diff --git a/hw/bsp/stm32f072disco/board.mk b/hw/bsp/stm32f072disco/board.mk new file mode 100644 index 000000000..0a58a5654 --- /dev/null +++ b/hw/bsp/stm32f072disco/board.mk @@ -0,0 +1,51 @@ +CFLAGS += \ + -DHSE_VALUE=8000000 \ + -DSTM32F072xB \ + -mthumb \ + -mabi=aapcs \ + -mcpu=cortex-m0 \ + -mfloat-abi=soft \ + -nostdlib -nostartfiles \ + -DCFG_EXAMPLE_MSC_READONLY \ + -DCFG_TUSB_MCU=OPT_MCU_STM32F0 + +ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F0xx_HAL_Driver +ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F0xx + +# All source paths should be relative to the top level. +LD_FILE = hw/bsp/$(BOARD)/STM32F072RBTx_FLASH.ld + +SRC_C += \ + $(ST_CMSIS)/Source/Templates/system_stm32f0xx.c \ + $(ST_HAL_DRIVER)/Src/stm32f0xx_hal.c \ + $(ST_HAL_DRIVER)/Src/stm32f0xx_hal_cortex.c \ + $(ST_HAL_DRIVER)/Src/stm32f0xx_hal_rcc.c \ + $(ST_HAL_DRIVER)/Src/stm32f0xx_hal_rcc_ex.c \ + $(ST_HAL_DRIVER)/Src/stm32f0xx_hal_gpio.c + +SRC_S += \ + $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f072xb.s + +INC += \ + $(TOP)/hw/mcu/st/st_driver/CMSIS/Include \ + $(TOP)/$(ST_CMSIS)/Include \ + $(TOP)/$(ST_HAL_DRIVER)/Inc \ + $(TOP)/hw/bsp/$(BOARD) + +# For TinyUSB port source +VENDOR = st +CHIP_FAMILY = stm32_fsdev + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM0 + +# For flash-jlink target +JLINK_DEVICE = stm32f072rb +JLINK_IF = swd + +# Path to STM32 Cube Programmer CLI, should be added into system path +STM32Prog = STM32_Programmer_CLI + +# flash target using on-board stlink +flash: $(BUILD)/$(BOARD)-firmware.elf + $(STM32Prog) --connect port=swd --write $< --go diff --git a/hw/bsp/stm32f072disco/stm32f072disco.c b/hw/bsp/stm32f072disco/stm32f072disco.c new file mode 100644 index 000000000..cb9a1ddb5 --- /dev/null +++ b/hw/bsp/stm32f072disco/stm32f072disco.c @@ -0,0 +1,173 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "../board.h" + +#include "stm32f0xx.h" +#include "stm32f0xx_hal_conf.h" + +#define LED_PORT GPIOC +#define LED_PIN GPIO_PIN_6 +#define LED_STATE_ON 1 + +#define BUTTON_PORT GPIOA +#define BUTTON_PIN GPIO_PIN_0 +#define BUTTON_STATE_ACTIVE 1 + + +/** + * @brief System Clock Configuration + * The system Clock is configured as follow : + * System Clock source = PLL (HSI48) + * SYSCLK(Hz) = 48000000 + * HCLK(Hz) = 48000000 + * AHB Prescaler = 1 + * APB1 Prescaler = 1 + * HSI Frequency(Hz) = 48000000 + * PREDIV = 2 + * PLLMUL = 2 + * Flash Latency(WS) = 1 + * @param None + * @retval None + */ +static void SystemClock_Config(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + + /* Select HSI48 Oscillator as PLL source */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48; + RCC_OscInitStruct.HSI48State = RCC_HSI48_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI48; + RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV2; + RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL2; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + /* Select PLL as system clock source and configure the HCLK and PCLK1 clocks dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1); + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1); +} + +void board_init(void) +{ + #if CFG_TUSB_OS == OPT_OS_NONE + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); + #endif + + SystemClock_Config(); + + // Notify runtime of frequency change. + SystemCoreClockUpdate(); + + // LED + __HAL_RCC_GPIOC_CLK_ENABLE(); + GPIO_InitTypeDef GPIO_InitStruct; + GPIO_InitStruct.Pin = LED_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); + + // Button + __HAL_RCC_GPIOA_CLK_ENABLE(); + GPIO_InitStruct.Pin = BUTTON_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_PULLDOWN; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); + + // USB Pins + // Configure USB DM and DP pins. This is optional, and maintained only for user guidance. + GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12); + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + // USB Clock enable + __HAL_RCC_USB_CLK_ENABLE(); +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + HAL_GPIO_WritePin(LED_PORT, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); +} + +uint32_t board_button_read(void) +{ + return BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN); +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler (void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif + +void HardFault_Handler (void) +{ + asm("bkpt"); +} + +#ifdef USE_FULL_ASSERT +/** + * @brief Reports the name of the source file and the source line number + * where the assert_param error has occurred. + * @param file: pointer to the source file name + * @param line: assert_param error line source number + * @retval None + */ +void assert_failed(char *file, uint32_t line) +{ + /* USER CODE BEGIN 6 */ + /* User can add his own implementation to report the file name and line number, + tex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ + /* USER CODE END 6 */ +} +#endif /* USE_FULL_ASSERT */ + +// Required by __libc_init_array in startup code if we are compiling using +// -nostdlib/-nostartfiles. +void _init(void) +{ + +} diff --git a/hw/bsp/stm32f072disco/stm32f0xx_hal_conf.h b/hw/bsp/stm32f072disco/stm32f0xx_hal_conf.h new file mode 100644 index 000000000..7e3721afc --- /dev/null +++ b/hw/bsp/stm32f072disco/stm32f0xx_hal_conf.h @@ -0,0 +1,324 @@ +/** + ****************************************************************************** + * @file GPIO/GPIO_IOToggle/Inc/stm32f3xx_hal_conf.h + * @author MCD Application Team + * @brief HAL configuration file. + ****************************************************************************** + * @attention + * + *

© COPYRIGHT(c) 2016 STMicroelectronics

+ * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F0xx_HAL_CONF_H +#define __STM32F0xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +/*#define HAL_ADC_MODULE_ENABLED */ +/*#define HAL_CRYP_MODULE_ENABLED */ +/*#define HAL_CAN_MODULE_ENABLED */ +/*#define HAL_CEC_MODULE_ENABLED */ +/*#define HAL_COMP_MODULE_ENABLED */ +/*#define HAL_CRC_MODULE_ENABLED */ +/*#define HAL_CRYP_MODULE_ENABLED */ +/*#define HAL_TSC_MODULE_ENABLED */ +/*#define HAL_DAC_MODULE_ENABLED */ +/*#define HAL_I2S_MODULE_ENABLED */ +/*#define HAL_IWDG_MODULE_ENABLED */ +/*#define HAL_LCD_MODULE_ENABLED */ +/*#define HAL_LPTIM_MODULE_ENABLED */ +/*#define HAL_RNG_MODULE_ENABLED */ +/*#define HAL_RTC_MODULE_ENABLED */ +/*#define HAL_SPI_MODULE_ENABLED */ +/*#define HAL_TIM_MODULE_ENABLED */ +/*#define HAL_UART_MODULE_ENABLED */ +#define HAL_USART_MODULE_ENABLED +/*#define HAL_IRDA_MODULE_ENABLED */ +/*#define HAL_SMARTCARD_MODULE_ENABLED */ +/*#define HAL_SMBUS_MODULE_ENABLED */ +/*#define HAL_WWDG_MODULE_ENABLED */ +#define HAL_PCD_MODULE_ENABLED +/*#define HAL_EXTI_MODULE_ENABLED */ +#define HAL_CORTEX_MODULE_ENABLED +#define HAL_DMA_MODULE_ENABLED +#define HAL_FLASH_MODULE_ENABLED +#define HAL_GPIO_MODULE_ENABLED +#define HAL_PWR_MODULE_ENABLED +#define HAL_RCC_MODULE_ENABLED +#define HAL_I2C_MODULE_ENABLED + +/* ########################## HSE/HSI Values adaptation ##################### */ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) + #define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +/** + * @brief In the following line adjust the External High Speed oscillator (HSE) Startup + * Timeout value + */ +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT ((uint32_t)100) /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) + #define HSI_VALUE ((uint32_t)8000000) /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup + * Timeout value + */ +#if !defined (HSI_STARTUP_TIMEOUT) + #define HSI_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSI start up */ +#endif /* HSI_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator for ADC (HSI14) value. + */ +#if !defined (HSI14_VALUE) +#define HSI14_VALUE ((uint32_t)14000000) /*!< Value of the Internal High Speed oscillator for ADC in Hz. + The real value may vary depending on the variations + in voltage and temperature. */ +#endif /* HSI14_VALUE */ + +/** + * @brief Internal High Speed oscillator for USB (HSI48) value. + */ +#if !defined (HSI48_VALUE) +#define HSI48_VALUE ((uint32_t)48000000) /*!< Value of the Internal High Speed oscillator for USB in Hz. + The real value may vary depending on the variations + in voltage and temperature. */ +#endif /* HSI48_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#if !defined (LSI_VALUE) + #define LSI_VALUE ((uint32_t)40000) +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature. */ +/** + * @brief External Low Speed oscillator (LSI) value. + */ +#if !defined (LSE_VALUE) + #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */ +#endif /* LSE_VALUE */ + +#if !defined (LSE_STARTUP_TIMEOUT) + #define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY ((uint32_t)0) /*!< tick interrupt priority (lowest by default) */ + /* Warning: Must be set to higher priority for HAL_Delay() */ + /* and HAL_GetTick() usage under interrupt context */ +#define USE_RTOS 0 +#define PREFETCH_ENABLE 1 +#define INSTRUCTION_CACHE_ENABLE 0 +#define DATA_CACHE_ENABLE 0 +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ + #define USE_FULL_ASSERT 1U + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver +* Activated: CRC code is present inside driver +* Deactivated: CRC code cleaned from driver +*/ + +#define USE_SPI_CRC 0U + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32f0xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_EXTI_MODULE_ENABLED + #include "stm32f0xx_hal_exti.h" +#endif /* HAL_EXTI_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32f0xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32f0xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32f0xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32f0xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED + #include "stm32f0xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED + #include "stm32f0xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_COMP_MODULE_ENABLED + #include "stm32f0xx_hal_comp.h" +#endif /* HAL_COMP_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32f0xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32f0xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32f0xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32f0xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED + #include "stm32f0xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32f0xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32f0xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32f0xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32f0xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32f0xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32f0xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_SMBUS_MODULE_ENABLED + #include "stm32f0xx_hal_smbus.h" +#endif /* HAL_SMBUS_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32f0xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32f0xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_TSC_MODULE_ENABLED + #include "stm32f0xx_hal_tsc.h" +#endif /* HAL_TSC_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32f0xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32f0xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32f0xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0U : assert_failed((char *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(char* file, uint32_t line); +#else + #define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F0xx_HAL_CONF_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/