diff --git a/examples/device/cdc_msc/src/tusb_config.h b/examples/device/cdc_msc/src/tusb_config.h
index c57c2ead8..13021d5d3 100644
--- a/examples/device/cdc_msc/src/tusb_config.h
+++ b/examples/device/cdc_msc/src/tusb_config.h
@@ -102,8 +102,8 @@
#define CFG_TUD_VENDOR 0
// CDC FIFO size of TX and RX
-#define CFG_TUD_CDC_RX_BUFSIZE 64
-#define CFG_TUD_CDC_TX_BUFSIZE 64
+#define CFG_TUD_CDC_RX_BUFSIZE (TUD_OPT_HIGH_SPEED ? 512 : 64)
+#define CFG_TUD_CDC_TX_BUFSIZE (TUD_OPT_HIGH_SPEED ? 512 : 64)
// MSC Buffer size of Device Mass storage
#define CFG_TUD_MSC_BUFSIZE 512
diff --git a/examples/device/cdc_msc/src/usb_descriptors.c b/examples/device/cdc_msc/src/usb_descriptors.c
index 62ab4f10f..9a4d71f24 100644
--- a/examples/device/cdc_msc/src/usb_descriptors.c
+++ b/examples/device/cdc_msc/src/usb_descriptors.c
@@ -120,7 +120,7 @@ uint8_t const desc_configuration[] =
TUD_CONFIG_DESCRIPTOR(1, ITF_NUM_TOTAL, 0, CONFIG_TOTAL_LEN, TUSB_DESC_CONFIG_ATT_REMOTE_WAKEUP, 100),
// Interface number, string index, EP notification address and size, EP data address (out, in) and size.
- TUD_CDC_DESCRIPTOR(ITF_NUM_CDC, 4, EPNUM_CDC_NOTIF, 8, EPNUM_CDC_OUT, EPNUM_CDC_IN, 64),
+ TUD_CDC_DESCRIPTOR(ITF_NUM_CDC, 4, EPNUM_CDC_NOTIF, 8, EPNUM_CDC_OUT, EPNUM_CDC_IN, TUD_OPT_HIGH_SPEED ? 512 : 64),
// Interface number, string index, EP Out & EP In address, EP size
TUD_MSC_DESCRIPTOR(ITF_NUM_MSC, 5, EPNUM_MSC_OUT, EPNUM_MSC_IN, TUD_OPT_HIGH_SPEED ? 512 : 64),
diff --git a/examples/readme.md b/examples/readme.md
index ca28d4881..790427cd2 100644
--- a/examples/readme.md
+++ b/examples/readme.md
@@ -37,6 +37,10 @@ To compile for debugging with debug symbols add DEBUG=1, for example
```
$ make BOARD=feather_nrf52840_express DEBUG=1 all
+If a board has several ports, one port is choosen by default in the individual board.mk file. Choose another port with PORT=x. For example to select the HS port of a STM32F746Disco board, use:
+
+```
+$ make BOARD=stm32f746disco PORT=1 all
```
### Debug Log
diff --git a/hw/bsp/stm32f723disco/STM32F723xE_FLASH.ld b/hw/bsp/stm32f723disco/STM32F723xE_FLASH.ld
new file mode 100644
index 000000000..8645ce5c5
--- /dev/null
+++ b/hw/bsp/stm32f723disco/STM32F723xE_FLASH.ld
@@ -0,0 +1,167 @@
+/*
+*****************************************************************************
+**
+
+** File : LinkerScript.ld
+**
+** Abstract : Linker script for STM32F723xE Device with
+** 512KByte FLASH, 256KByte RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+**
+** Distribution: The file is distributed as is, without any warranty
+** of any kind.
+**
+** (c)Copyright Ac6.
+** You may use this file as-is or modify it according to the needs of your
+** project. Distribution of this file (unmodified or modified) is not
+** permitted. Ac6 permit registered System Workbench for MCU users the
+** rights to distribute the assembled, compiled & linked contents of this
+** file as part of an application binary file, provided that it is built
+** using the System Workbench for MCU toolchain.
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = 0x20040000; /* end of RAM */
+/* Generate a link error if heap and stack don't fit into RAM */
+_Min_Heap_Size = 0x200; /* required amount of heap */
+_Min_Stack_Size = 0x460; /* required amount of stack */
+
+/* Specify the memory areas */
+MEMORY
+{
+RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 256K
+FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 512K
+}
+
+/* Define output sections */
+SECTIONS
+{
+ /* The startup code goes first into FLASH */
+ .isr_vector :
+ {
+ . = ALIGN(4);
+ KEEP(*(.isr_vector)) /* Startup code */
+ . = ALIGN(4);
+ } >FLASH
+
+ /* The program code and other data goes into FLASH */
+ .text :
+ {
+ . = ALIGN(4);
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ . = ALIGN(4);
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data goes into FLASH */
+ .rodata :
+ {
+ . = ALIGN(4);
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
+ .ARM : {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections goes into RAM, load LMA copy after code */
+ .data :
+ {
+ . = ALIGN(4);
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+
+ . = ALIGN(4);
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+
+ /* Uninitialized data section */
+ . = ALIGN(4);
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss secion */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ . = ALIGN(4);
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough RAM left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+
+
+ /* Remove information from the standard libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32f723disco/board.mk b/hw/bsp/stm32f723disco/board.mk
new file mode 100644
index 000000000..2bd3b0756
--- /dev/null
+++ b/hw/bsp/stm32f723disco/board.mk
@@ -0,0 +1,59 @@
+PORT ?= 0
+
+CFLAGS += \
+ -flto \
+ -mthumb \
+ -mabi=aapcs \
+ -mcpu=cortex-m7 \
+ -mfloat-abi=hard \
+ -mfpu=fpv5-d16 \
+ -nostdlib -nostartfiles \
+ -DSTM32F723xx \
+ -DHSE_VALUE=25000000 \
+ -DCFG_TUSB_MCU=OPT_MCU_STM32F7 \
+ -DBOARD_DEVICE_RHPORT_NUM=$(PORT)
+
+ifeq ($(PORT), 1)
+CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED
+$(info "PORT1 HS")
+else
+$(info "PORT0")
+endif
+
+# mcu driver cause following warnings
+CFLAGS += -Wno-error=shadow -Wno-error=cast-align
+
+ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F7xx_HAL_Driver
+ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F7xx
+
+# All source paths should be relative to the top level.
+LD_FILE = hw/bsp/$(BOARD)/STM32F723xE_FLASH.ld
+
+SRC_C += \
+ $(ST_CMSIS)/Source/Templates/system_stm32f7xx.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_cortex.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_rcc.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_rcc_ex.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_gpio.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_uart.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_pwr_ex.c
+
+SRC_S += \
+ $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f723xx.s
+
+INC += \
+ $(TOP)/hw/mcu/st/st_driver/CMSIS/Include \
+ $(TOP)/$(ST_CMSIS)/Include \
+ $(TOP)/$(ST_HAL_DRIVER)/Inc \
+ $(TOP)/hw/bsp/$(BOARD)
+
+# For TinyUSB port source
+VENDOR = st
+CHIP_FAMILY = synopsys
+
+# For freeRTOS port source
+FREERTOS_PORT = ARM_CM7/r0p1
+
+# flash target using on-board stlink
+flash: flash-stlink
diff --git a/hw/bsp/stm32f723disco/stm32f723disco.c b/hw/bsp/stm32f723disco/stm32f723disco.c
new file mode 100644
index 000000000..eeedd2a66
--- /dev/null
+++ b/hw/bsp/stm32f723disco/stm32f723disco.c
@@ -0,0 +1,304 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2020 Uwe Bonnes (bon@elektron.ikp.physik.tu-darmstadt.de),
+ * Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#include "../board.h"
+
+#include "stm32f7xx_hal.h"
+
+//--------------------------------------------------------------------+
+// Forward USB interrupt events to TinyUSB IRQ Handler
+//--------------------------------------------------------------------+
+void OTG_FS_IRQHandler(void)
+{
+ tud_int_handler(0);
+}
+
+// Despite being call USB2_OTG
+// OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port
+void OTG_HS_IRQHandler(void)
+{
+ tud_int_handler(1);
+}
+
+
+//--------------------------------------------------------------------+
+// MACRO TYPEDEF CONSTANT ENUM
+//--------------------------------------------------------------------+
+
+#define LED_PORT GPIOB
+#define LED_PIN GPIO_PIN_1
+#define LED_STATE_ON 1
+
+#define BUTTON_PORT GPIOA
+#define BUTTON_PIN GPIO_PIN_0
+#define BUTTON_STATE_ACTIVE 1
+
+#define UARTx USART6
+#define UART_GPIO_PORT GPIOC
+#define UART_GPIO_AF GPIO_AF8_USART6
+#define UART_TX_PIN GPIO_PIN_6
+#define UART_RX_PIN GPIO_PIN_7
+
+UART_HandleTypeDef UartHandle;
+
+// enable all LED, Button, Uart, USB clock
+static void all_rcc_clk_enable(void)
+{
+ __HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D-
+ __HAL_RCC_GPIOB_CLK_ENABLE(); // LED, OTG_HS
+ __HAL_RCC_GPIOC_CLK_ENABLE(); // Button
+ __HAL_RCC_GPIOD_CLK_ENABLE(); // Uart tx, rx
+ __HAL_RCC_USART6_CLK_ENABLE(); // Uart module
+}
+
+/**
+ * @brief System Clock Configuration
+ * The system Clock is configured as follow :
+ * System Clock source = PLL (HSE)
+ * SYSCLK(Hz) = 216000000
+ * HCLK(Hz) = 216000000
+ * AHB Prescaler = 1
+ * APB1 Prescaler = 4
+ * APB2 Prescaler = 2
+ * HSE Frequency(Hz) = 25000000
+ * PLL_M = HSE_VALUE/1000000
+ * PLL_N = 432
+ * PLL_P = 2
+ * PLL_Q = 9
+ * VDD(V) = 3.3
+ * Main regulator output voltage = Scale1 mode
+ * Flash Latency(WS) = 7
+ * The USB clock configuration from PLLSAI:
+ * PLLSAIP = 8
+ * PLLSAIN = 384
+ * PLLSAIQ = 7
+ * @param None
+ * @retval None
+ */
+void SystemClock_Config(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* Enable Power Control clock */
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ /* Enable HSE Oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000;
+ RCC_OscInitStruct.PLL.PLLN = 432;
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+ RCC_OscInitStruct.PLL.PLLQ = 9;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ /* Activate the OverDrive to reach the 216 MHz Frequency */
+ HAL_PWREx_EnableOverDrive();
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
+
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7);
+}
+
+void board_init(void)
+{
+
+
+ SystemClock_Config();
+ all_rcc_clk_enable();
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+ // 1ms tick timer
+ SysTick_Config(SystemCoreClock / 1000);
+#endif
+
+ GPIO_InitTypeDef GPIO_InitStruct;
+
+ // LED
+ GPIO_InitStruct.Pin = LED_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
+
+ // Button
+ GPIO_InitStruct.Pin = BUTTON_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct);
+
+ // Uart
+ GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ GPIO_InitStruct.Alternate = UART_GPIO_AF;
+ HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct);
+
+ UartHandle.Instance = UARTx;
+ UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE;
+ UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
+ UartHandle.Init.StopBits = UART_STOPBITS_1;
+ UartHandle.Init.Parity = UART_PARITY_NONE;
+ UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
+ UartHandle.Init.Mode = UART_MODE_TX_RX;
+ UartHandle.Init.OverSampling = UART_OVERSAMPLING_16;
+ HAL_UART_Init(&UartHandle);
+
+#if BOARD_DEVICE_RHPORT_NUM == 0
+ /* Configure USB FS GPIOs */
+ /* Configure DM DP Pins */
+ GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12);
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* Configure VBUS Pin */
+ GPIO_InitStruct.Pin = GPIO_PIN_9;
+ GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* Configure OTG-FS ID pin */
+ GPIO_InitStruct.Pin = GPIO_PIN_10;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_OD;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* Enable USB FS Clocks */
+ __HAL_RCC_USB_OTG_FS_CLK_ENABLE();
+
+ // Enable VBUS sense (B device) via pin PA9
+ USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN;
+
+#else
+ /* Configure USB HS GPIOs */
+ /* Configure DM DP Pins */
+ GPIO_InitStruct.Pin = (GPIO_PIN_14 | GPIO_PIN_15);
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
+ HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+ // Enable HS VBUS sense (B device) via pin PB13
+ USB_OTG_HS->GCCFG |= USB_OTG_GCCFG_VBDEN;
+
+ /* Configure OTG-HS ID pin */
+ GPIO_InitStruct.Pin = GPIO_PIN_13;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_OD;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
+ HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
+
+ /* Enable PHYC Clocks */
+ __HAL_RCC_OTGPHYC_CLK_ENABLE();
+
+ /* Enable USB HS Clocks */
+ __HAL_RCC_USB_OTG_HS_CLK_ENABLE();
+ __HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE();
+
+ // Enable VBUS sense (B device) via pin PA9
+ USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN;
+
+ // B-peripheral session valid override enable
+ USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN;
+ USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL;
+
+ // Force device mode
+ USB_OTG_HS->GUSBCFG &= ~USB_OTG_GUSBCFG_FHMOD;
+ USB_OTG_HS->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD;
+
+#endif
+}
+
+//--------------------------------------------------------------------+
+// Board porting API
+//--------------------------------------------------------------------+
+
+void board_led_write(bool state)
+{
+ HAL_GPIO_WritePin(LED_PORT, LED_PIN, state);
+}
+
+uint32_t board_button_read(void)
+{
+ return HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN);
+}
+
+int board_uart_read(uint8_t* buf, int len)
+{
+ (void) buf; (void) len;
+ return 0;
+}
+
+int board_uart_write(void const * buf, int len)
+{
+ HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff);
+ return len;
+}
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+volatile uint32_t system_ticks = 0;
+void SysTick_Handler (void)
+{
+ system_ticks++;
+}
+
+uint32_t board_millis(void)
+{
+ return system_ticks;
+}
+#endif
+
+void HardFault_Handler (void)
+{
+ asm("bkpt");
+}
+
+// Required by __libc_init_array in startup code if we are compiling using
+// -nostdlib/-nostartfiles.
+void _init(void)
+{
+
+}
diff --git a/hw/bsp/stm32f723disco/stm32f7xx_hal_conf.h b/hw/bsp/stm32f723disco/stm32f7xx_hal_conf.h
new file mode 100644
index 000000000..03dec8f0d
--- /dev/null
+++ b/hw/bsp/stm32f723disco/stm32f7xx_hal_conf.h
@@ -0,0 +1,472 @@
+/**
+ ******************************************************************************
+ * @file stm32f7xx_hal_conf.h
+ * @author MCD Application Team
+ * @brief HAL configuration file.
+ ******************************************************************************
+ * @attention
+ *
+ *
© Copyright (c) 2016 STMicroelectronics.
+ * All rights reserved.
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F7xx_HAL_CONF_H
+#define __STM32F7xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+ * @brief This is the list of modules to be used in the HAL driver
+ */
+#define HAL_MODULE_ENABLED
+/* #define HAL_ADC_MODULE_ENABLED */
+/* #define HAL_CAN_MODULE_ENABLED */
+/* #define HAL_CAN_LEGACY_MODULE_ENABLED */
+/* #define HAL_CEC_MODULE_ENABLED */
+/* #define HAL_CRC_MODULE_ENABLED */
+/* #define HAL_CRYP_MODULE_ENABLED */
+/* #define HAL_DAC_MODULE_ENABLED */
+/* #define HAL_DCMI_MODULE_ENABLED */
+#define HAL_DMA_MODULE_ENABLED
+/* #define HAL_DMA2D_MODULE_ENABLED */
+/* #define HAL_ETH_MODULE_ENABLED */
+#define HAL_FLASH_MODULE_ENABLED
+/* #define HAL_NAND_MODULE_ENABLED */
+/* #define HAL_NOR_MODULE_ENABLED */
+/* #define HAL_SRAM_MODULE_ENABLED */
+/* #define HAL_SDRAM_MODULE_ENABLED */
+/* #define HAL_HASH_MODULE_ENABLED */
+#define HAL_GPIO_MODULE_ENABLED
+/* #define HAL_I2C_MODULE_ENABLED */
+/* #define HAL_I2S_MODULE_ENABLED */
+/* #define HAL_IWDG_MODULE_ENABLED */
+/* #define HAL_LPTIM_MODULE_ENABLED */
+/* #define HAL_LTDC_MODULE_ENABLED */
+#define HAL_PWR_MODULE_ENABLED
+/* #define HAL_QSPI_MODULE_ENABLED */
+#define HAL_RCC_MODULE_ENABLED
+/* #define HAL_RNG_MODULE_ENABLED */
+/* #define HAL_RTC_MODULE_ENABLED */
+/* #define HAL_SAI_MODULE_ENABLED */
+/* #define HAL_SD_MODULE_ENABLED */
+/* #define HAL_SPDIFRX_MODULE_ENABLED */
+/* #define HAL_SPI_MODULE_ENABLED */
+/* #define HAL_TIM_MODULE_ENABLED */
+#define HAL_UART_MODULE_ENABLED
+/* #define HAL_USART_MODULE_ENABLED */
+/* #define HAL_IRDA_MODULE_ENABLED */
+/* #define HAL_SMARTCARD_MODULE_ENABLED */
+/* #define HAL_WWDG_MODULE_ENABLED */
+#define HAL_CORTEX_MODULE_ENABLED
+/* #define HAL_PCD_MODULE_ENABLED */
+/* #define HAL_HCD_MODULE_ENABLED */
+/* #define HAL_DFSDM_MODULE_ENABLED */
+/* #define HAL_DSI_MODULE_ENABLED */
+/* #define HAL_JPEG_MODULE_ENABLED */
+/* #define HAL_MDIOS_MODULE_ENABLED */
+
+
+/* ########################## HSE/HSI Values adaptation ##################### */
+/**
+ * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSE is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined (HSE_STARTUP_TIMEOUT)
+ #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator (HSI) value.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSI is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+ * @brief Internal Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSI_VALUE)
+ #define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/
+#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+/**
+ * @brief External Low Speed oscillator (LSE) value.
+ */
+#if !defined (LSE_VALUE)
+ #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+#if !defined (LSE_STARTUP_TIMEOUT)
+ #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief External clock source for I2S peripheral
+ * This value is used by the I2S HAL module to compute the I2S clock source
+ * frequency, this source is inserted directly through I2S_CKIN pad.
+ */
+#if !defined (EXTERNAL_CLOCK_VALUE)
+ #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the Internal oscillator in Hz*/
+#endif /* EXTERNAL_CLOCK_VALUE */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+ === you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+ * @brief This is the HAL system configuration section
+ */
+#define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY ((uint32_t)0x0FU) /*!< tick interrupt priority */
+#define USE_RTOS 0U
+#define PREFETCH_ENABLE 1U
+#define ART_ACCLERATOR_ENABLE 1U /* To enable instruction cache and prefetch */
+
+#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */
+#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */
+#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */
+#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */
+#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */
+#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */
+#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */
+#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */
+#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */
+#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */
+#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */
+#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */
+#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */
+#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */
+#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */
+#define USE_HAL_JPEG_REGISTER_CALLBACKS 0U /* JPEG register callback disabled */
+#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */
+#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */
+#define USE_HAL_MDIOS_REGISTER_CALLBACKS 0U /* MDIOS register callback disabled */
+#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */
+#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */
+#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */
+#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */
+#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */
+#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */
+#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */
+#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */
+#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */
+#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */
+#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */
+#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */
+#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */
+#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */
+#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */
+#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */
+#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */
+#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */
+#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */
+
+/* ########################## Assert Selection ############################## */
+/**
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * HAL drivers code
+ */
+/* #define USE_FULL_ASSERT 1 */
+
+/* ################## Ethernet peripheral configuration for NUCLEO 144 board ##################### */
+
+/* Section 1 : Ethernet peripheral configuration */
+
+/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
+#define MAC_ADDR0 2U
+#define MAC_ADDR1 0U
+#define MAC_ADDR2 0U
+#define MAC_ADDR3 0U
+#define MAC_ADDR4 0U
+#define MAC_ADDR5 0U
+
+/* Definition of the Ethernet driver buffers size and count */
+#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
+#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
+#define ETH_RXBUFNB ((uint32_t)5) /* 5 Rx buffers of size ETH_RX_BUF_SIZE */
+#define ETH_TXBUFNB ((uint32_t)5) /* 5 Tx buffers of size ETH_TX_BUF_SIZE */
+
+/* Section 2: PHY configuration section */
+/* LAN8742A PHY Address*/
+#define LAN8742A_PHY_ADDRESS 0x00
+/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
+#define PHY_RESET_DELAY ((uint32_t)0x00000FFF)
+/* PHY Configuration delay */
+#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF)
+
+#define PHY_READ_TO ((uint32_t)0x0000FFFF)
+#define PHY_WRITE_TO ((uint32_t)0x0000FFFF)
+
+/* Section 3: Common PHY Registers */
+
+#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */
+#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */
+
+#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
+#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
+#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
+#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */
+#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */
+#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */
+#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */
+#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */
+#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */
+#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */
+
+#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
+#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
+#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
+
+/* Section 4: Extended PHY Registers */
+
+#define PHY_SR ((uint16_t)0x1F) /*!< PHY special control/ status register Offset */
+
+#define PHY_SPEED_STATUS ((uint16_t)0x0004) /*!< PHY Speed mask */
+#define PHY_DUPLEX_STATUS ((uint16_t)0x0010) /*!< PHY Duplex mask */
+
+
+#define PHY_ISFR ((uint16_t)0x1D) /*!< PHY Interrupt Source Flag register Offset */
+#define PHY_ISFR_INT4 ((uint16_t)0x0010) /*!< PHY Link down inturrupt */
+
+/* ################## SPI peripheral configuration ########################## */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+* Activated: CRC code is present inside driver
+* Deactivated: CRC code cleaned from driver
+*/
+
+#define USE_SPI_CRC 1U
+
+/* Includes ------------------------------------------------------------------*/
+/**
+ * @brief Include module's header file
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32f7xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32f7xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+ #include "stm32f7xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32f7xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32f7xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32f7xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
+ #include "stm32f7xx_hal_can_legacy.h"
+#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
+
+#ifdef HAL_CEC_MODULE_ENABLED
+ #include "stm32f7xx_hal_cec.h"
+#endif /* HAL_CEC_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32f7xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+ #include "stm32f7xx_hal_cryp.h"
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DMA2D_MODULE_ENABLED
+ #include "stm32f7xx_hal_dma2d.h"
+#endif /* HAL_DMA2D_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32f7xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_DCMI_MODULE_ENABLED
+ #include "stm32f7xx_hal_dcmi.h"
+#endif /* HAL_DCMI_MODULE_ENABLED */
+
+#ifdef HAL_ETH_MODULE_ENABLED
+ #include "stm32f7xx_hal_eth.h"
+#endif /* HAL_ETH_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32f7xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+ #include "stm32f7xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+ #include "stm32f7xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+ #include "stm32f7xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_SDRAM_MODULE_ENABLED
+ #include "stm32f7xx_hal_sdram.h"
+#endif /* HAL_SDRAM_MODULE_ENABLED */
+
+#ifdef HAL_HASH_MODULE_ENABLED
+ #include "stm32f7xx_hal_hash.h"
+#endif /* HAL_HASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f7xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f7xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f7xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_LPTIM_MODULE_ENABLED
+ #include "stm32f7xx_hal_lptim.h"
+#endif /* HAL_LPTIM_MODULE_ENABLED */
+
+#ifdef HAL_LTDC_MODULE_ENABLED
+ #include "stm32f7xx_hal_ltdc.h"
+#endif /* HAL_LTDC_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f7xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_QSPI_MODULE_ENABLED
+ #include "stm32f7xx_hal_qspi.h"
+#endif /* HAL_QSPI_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+ #include "stm32f7xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f7xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SAI_MODULE_ENABLED
+ #include "stm32f7xx_hal_sai.h"
+#endif /* HAL_SAI_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+ #include "stm32f7xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_SPDIFRX_MODULE_ENABLED
+ #include "stm32f7xx_hal_spdifrx.h"
+#endif /* HAL_SPDIFRX_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f7xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f7xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f7xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f7xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f7xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f7xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f7xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f7xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+ #include "stm32f7xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+#ifdef HAL_DFSDM_MODULE_ENABLED
+ #include "stm32f7xx_hal_dfsdm.h"
+#endif /* HAL_DFSDM_MODULE_ENABLED */
+
+#ifdef HAL_DSI_MODULE_ENABLED
+ #include "stm32f7xx_hal_dsi.h"
+#endif /* HAL_DSI_MODULE_ENABLED */
+
+#ifdef HAL_JPEG_MODULE_ENABLED
+ #include "stm32f7xx_hal_jpeg.h"
+#endif /* HAL_JPEG_MODULE_ENABLED */
+
+#ifdef HAL_MDIOS_MODULE_ENABLED
+ #include "stm32f7xx_hal_mdios.h"
+#endif /* HAL_MDIOS_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr: If expr is false, it calls assert_failed function
+ * which reports the name of the source file and the source
+ * line number of the call that failed.
+ * If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(uint8_t* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F7xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/hw/bsp/stm32f746disco/STM32F746ZGTx_FLASH.ld b/hw/bsp/stm32f746disco/STM32F746ZGTx_FLASH.ld
new file mode 100644
index 000000000..045ec76f9
--- /dev/null
+++ b/hw/bsp/stm32f746disco/STM32F746ZGTx_FLASH.ld
@@ -0,0 +1,167 @@
+/*
+*****************************************************************************
+**
+
+** File : LinkerScript.ld
+**
+** Abstract : Linker script for STM32F746ZGTx Device with
+** 1024KByte FLASH, 320KByte RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+**
+** Distribution: The file is distributed as is, without any warranty
+** of any kind.
+**
+** (c)Copyright Ac6.
+** You may use this file as-is or modify it according to the needs of your
+** project. Distribution of this file (unmodified or modified) is not
+** permitted. Ac6 permit registered System Workbench for MCU users the
+** rights to distribute the assembled, compiled & linked contents of this
+** file as part of an application binary file, provided that it is built
+** using the System Workbench for MCU toolchain.
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = 0x20050000; /* end of RAM */
+/* Generate a link error if heap and stack don't fit into RAM */
+_Min_Heap_Size = 0x200; /* required amount of heap */
+_Min_Stack_Size = 0x460; /* required amount of stack */
+
+/* Specify the memory areas */
+MEMORY
+{
+RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 320K
+FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 1024K
+}
+
+/* Define output sections */
+SECTIONS
+{
+ /* The startup code goes first into FLASH */
+ .isr_vector :
+ {
+ . = ALIGN(4);
+ KEEP(*(.isr_vector)) /* Startup code */
+ . = ALIGN(4);
+ } >FLASH
+
+ /* The program code and other data goes into FLASH */
+ .text :
+ {
+ . = ALIGN(4);
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ . = ALIGN(4);
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data goes into FLASH */
+ .rodata :
+ {
+ . = ALIGN(4);
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
+ .ARM : {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections goes into RAM, load LMA copy after code */
+ .data :
+ {
+ . = ALIGN(4);
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+
+ . = ALIGN(4);
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+
+ /* Uninitialized data section */
+ . = ALIGN(4);
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss secion */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ . = ALIGN(4);
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough RAM left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+
+
+ /* Remove information from the standard libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32f746disco/board.mk b/hw/bsp/stm32f746disco/board.mk
new file mode 100644
index 000000000..76a54cdfd
--- /dev/null
+++ b/hw/bsp/stm32f746disco/board.mk
@@ -0,0 +1,59 @@
+PORT ?= 0
+
+CFLAGS += \
+ -flto \
+ -mthumb \
+ -mabi=aapcs \
+ -mcpu=cortex-m7 \
+ -mfloat-abi=hard \
+ -mfpu=fpv5-d16 \
+ -nostdlib -nostartfiles \
+ -DSTM32F746xx \
+ -DHSE_VALUE=25000000 \
+ -DCFG_TUSB_MCU=OPT_MCU_STM32F7 \
+ -DBOARD_DEVICE_RHPORT_NUM=$(PORT)
+
+ifeq ($(PORT), 1)
+CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED
+$(info "PORT1 HS")
+else
+$(info "PORT0")
+endif
+
+# mcu driver cause following warnings
+CFLAGS += -Wno-error=shadow -Wno-error=cast-align
+
+ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F7xx_HAL_Driver
+ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F7xx
+
+# All source paths should be relative to the top level.
+LD_FILE = hw/bsp/$(BOARD)/STM32F746ZGTx_FLASH.ld
+
+SRC_C += \
+ $(ST_CMSIS)/Source/Templates/system_stm32f7xx.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_cortex.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_rcc.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_rcc_ex.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_gpio.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_uart.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_pwr_ex.c
+
+SRC_S += \
+ $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f746xx.s
+
+INC += \
+ $(TOP)/hw/mcu/st/st_driver/CMSIS/Include \
+ $(TOP)/$(ST_CMSIS)/Include \
+ $(TOP)/$(ST_HAL_DRIVER)/Inc \
+ $(TOP)/hw/bsp/$(BOARD)
+
+# For TinyUSB port source
+VENDOR = st
+CHIP_FAMILY = synopsys
+
+# For freeRTOS port source
+FREERTOS_PORT = ARM_CM7/r0p1
+
+# flash target using on-board stlink
+flash: flash-stlink
diff --git a/hw/bsp/stm32f746disco/stm32f746disco.c b/hw/bsp/stm32f746disco/stm32f746disco.c
new file mode 100644
index 000000000..c90182fcf
--- /dev/null
+++ b/hw/bsp/stm32f746disco/stm32f746disco.c
@@ -0,0 +1,353 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2020 Uwe Bonnes (bon@elektron.ikp.physik.tu-darmstadt.de),
+ * Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#include "../board.h"
+
+#include "stm32f7xx_hal.h"
+
+//--------------------------------------------------------------------+
+// Forward USB interrupt events to TinyUSB IRQ Handler
+//--------------------------------------------------------------------+
+
+// Despite being call USB2_OTG
+// OTG_FS is marked as RHPort0 by TinyUSB to be consistent across stm32 port
+void OTG_FS_IRQHandler(void)
+{
+ tud_int_handler(0);
+}
+
+// Despite being call USB2_OTG
+// OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port
+void OTG_HS_IRQHandler(void)
+{
+ tud_int_handler(1);
+}
+
+
+//--------------------------------------------------------------------+
+// MACRO TYPEDEF CONSTANT ENUM
+//--------------------------------------------------------------------+
+
+#define LED_PORT GPIOI
+#define LED_PIN GPIO_PIN_1
+#define LED_STATE_ON 1
+
+#define BUTTON_PORT GPIOI
+#define BUTTON_PIN GPIO_PIN_11
+#define BUTTON_STATE_ACTIVE 1
+
+#define UARTx USART1
+#define UART_TX_GPIO_PORT GPIOA
+#define UART_RX_GPIO_PORT GPIOB
+#define UART_TX_GPIO_AF GPIO_AF7_USART1
+#define UART_RX_GPIO_AF GPIO_AF7_USART1
+#define UART_TX_PIN GPIO_PIN_9
+#define UART_RX_PIN GPIO_PIN_7
+
+UART_HandleTypeDef UartHandle;
+
+// enable all LED, Button, Uart, USB clock
+static void all_rcc_clk_enable(void)
+{
+ __HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D-
+ __HAL_RCC_GPIOB_CLK_ENABLE(); // Uart rx
+ __HAL_RCC_GPIOI_CLK_ENABLE(); // Button
+ __HAL_RCC_USART1_CLK_ENABLE(); // Uart module
+}
+
+/**
+ * @brief System Clock Configuration
+ * The system Clock is configured as follow :
+ * System Clock source = PLL (HSE)
+ * SYSCLK(Hz) = 216000000
+ * HCLK(Hz) = 216000000
+ * AHB Prescaler = 1
+ * APB1 Prescaler = 4
+ * APB2 Prescaler = 2
+ * HSE Frequency(Hz) = 25000000
+ * PLL_M = HSE_VALUE/1000000
+ * PLL_N = 432
+ * PLL_P = 2
+ * PLL_Q = 9
+ * VDD(V) = 3.3
+ * Main regulator output voltage = Scale1 mode
+ * Flash Latency(WS) = 7
+ * The USB clock configuration from PLLSAI:
+ * PLLSAIP = 8
+ * PLLSAIN = 384
+ * PLLSAIQ = 7
+ * @param None
+ * @retval None
+ */
+void SystemClock_Config(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* Enable Power Control clock */
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ /* Enable HSE Oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000;
+ RCC_OscInitStruct.PLL.PLLN = 432;
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+ RCC_OscInitStruct.PLL.PLLQ = 9;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ /* Activate the OverDrive to reach the 216 MHz Frequency */
+ HAL_PWREx_EnableOverDrive();
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
+
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7);
+}
+
+void board_init(void)
+{
+
+
+ SystemClock_Config();
+ all_rcc_clk_enable();
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+ // 1ms tick timer
+ SysTick_Config(SystemCoreClock / 1000);
+#endif
+
+ GPIO_InitTypeDef GPIO_InitStruct;
+
+ // LED
+ GPIO_InitStruct.Pin = LED_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
+
+ // Button
+ GPIO_InitStruct.Pin = BUTTON_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct);
+
+ // Uart TX
+ GPIO_InitStruct.Pin = UART_TX_PIN ;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ GPIO_InitStruct.Alternate = UART_TX_GPIO_AF;
+ HAL_GPIO_Init(UART_TX_GPIO_PORT, &GPIO_InitStruct);
+
+ // Uart RX
+ GPIO_InitStruct.Pin = UART_RX_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ GPIO_InitStruct.Alternate = UART_RX_GPIO_AF;
+ HAL_GPIO_Init(UART_RX_GPIO_PORT, &GPIO_InitStruct);
+
+ UartHandle.Instance = UARTx;
+ UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE;
+ UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
+ UartHandle.Init.StopBits = UART_STOPBITS_1;
+ UartHandle.Init.Parity = UART_PARITY_NONE;
+ UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
+ UartHandle.Init.Mode = UART_MODE_TX_RX;
+ UartHandle.Init.OverSampling = UART_OVERSAMPLING_16;
+ HAL_UART_Init(&UartHandle);
+
+#if BOARD_DEVICE_RHPORT_NUM == 0
+ // Despite being call USB2_OTG
+ // OTG_FS is marked as RHPort0 by TinyUSB to be consistent across stm32 port
+ // PA9 VUSB, PA10 ID, PA11 DM, PA12 DP
+
+ /* Configure USB FS GPIOs */
+ /* Configure DM DP Pins */
+ GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12);
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* Configure VBUS Pin collides with USART TX*/
+// GPIO_InitStruct.Pin = GPIO_PIN_9;
+// GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+// GPIO_InitStruct.Pull = GPIO_NOPULL;
+// HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* Configure OTG-FS ID pin */
+ GPIO_InitStruct.Pin = GPIO_PIN_10;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_OD;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* Enable USB FS Clocks */
+ __HAL_RCC_USB_OTG_FS_CLK_ENABLE();
+
+ // Enable VBUS sense (B device) via pin PA9
+// USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN;
+#define DEVICE_BASE (USB_OTG_DeviceTypeDef *) (USB_OTG_FS_PERIPH_BASE + USB_OTG_DEVICE_BASE)
+ USB_OTG_DeviceTypeDef * dev = DEVICE_BASE;
+ dev->DCTL |= USB_OTG_DCTL_SDIS;
+
+ /* Deactivate VBUS Sensing B */
+ USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_VBDEN;
+
+ /* B-peripheral session valid override enable */
+ USB_OTG_FS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN;
+ USB_OTG_FS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL;
+#elif BOARD_DEVICE_RHPORT_NUM == 1
+ // Despite being call USB2_OTG
+ // OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port
+ __GPIOA_CLK_ENABLE();
+ __GPIOB_CLK_ENABLE();
+ __GPIOC_CLK_ENABLE();
+ __GPIOH_CLK_ENABLE();
+
+ /* ULPI CK */
+ GPIO_InitStruct.Pin = GPIO_PIN_5;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* ULPI D0 */
+ GPIO_InitStruct.Pin = GPIO_PIN_3;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* ULPI D1 D2 D3 D4 D5 D6 D7 */
+ GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12 | GPIO_PIN_13 | GPIO_PIN_5;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
+ HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+ /* ULPI STP DIR */
+ GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_2;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
+ HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
+
+ /* NXT */
+ GPIO_InitStruct.Pin = GPIO_PIN_4;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
+ HAL_GPIO_Init(GPIOH, &GPIO_InitStruct);
+
+ // Enable ULPI clock
+ __HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE();
+
+ /* Enable USB HS Clocks */
+ __HAL_RCC_USB_OTG_HS_CLK_ENABLE();
+
+ // No VBUS sense
+ USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN;
+
+ // B-peripheral session valid override enable
+ USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN;
+ USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL;
+
+ // Force device mode
+ USB_OTG_HS->GUSBCFG &= ~USB_OTG_GUSBCFG_FHMOD;
+ USB_OTG_HS->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD;
+
+#endif // rhport = 1
+}
+
+//--------------------------------------------------------------------+
+// Board porting API
+//--------------------------------------------------------------------+
+
+void board_led_write(bool state)
+{
+ HAL_GPIO_WritePin(LED_PORT, LED_PIN, state);
+}
+
+uint32_t board_button_read(void)
+{
+ return HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN);
+}
+
+int board_uart_read(uint8_t* buf, int len)
+{
+ (void) buf; (void) len;
+ return 0;
+}
+
+int board_uart_write(void const * buf, int len)
+{
+ HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff);
+ return len;
+}
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+volatile uint32_t system_ticks = 0;
+void SysTick_Handler (void)
+{
+ system_ticks++;
+}
+
+uint32_t board_millis(void)
+{
+ return system_ticks;
+}
+#endif
+
+void HardFault_Handler (void)
+{
+ asm("bkpt");
+}
+
+// Required by __libc_init_array in startup code if we are compiling using
+// -nostdlib/-nostartfiles.
+void _init(void)
+{
+
+}
diff --git a/hw/bsp/stm32f746disco/stm32f7xx_hal_conf.h b/hw/bsp/stm32f746disco/stm32f7xx_hal_conf.h
new file mode 100644
index 000000000..03dec8f0d
--- /dev/null
+++ b/hw/bsp/stm32f746disco/stm32f7xx_hal_conf.h
@@ -0,0 +1,472 @@
+/**
+ ******************************************************************************
+ * @file stm32f7xx_hal_conf.h
+ * @author MCD Application Team
+ * @brief HAL configuration file.
+ ******************************************************************************
+ * @attention
+ *
+ * © Copyright (c) 2016 STMicroelectronics.
+ * All rights reserved.
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F7xx_HAL_CONF_H
+#define __STM32F7xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+ * @brief This is the list of modules to be used in the HAL driver
+ */
+#define HAL_MODULE_ENABLED
+/* #define HAL_ADC_MODULE_ENABLED */
+/* #define HAL_CAN_MODULE_ENABLED */
+/* #define HAL_CAN_LEGACY_MODULE_ENABLED */
+/* #define HAL_CEC_MODULE_ENABLED */
+/* #define HAL_CRC_MODULE_ENABLED */
+/* #define HAL_CRYP_MODULE_ENABLED */
+/* #define HAL_DAC_MODULE_ENABLED */
+/* #define HAL_DCMI_MODULE_ENABLED */
+#define HAL_DMA_MODULE_ENABLED
+/* #define HAL_DMA2D_MODULE_ENABLED */
+/* #define HAL_ETH_MODULE_ENABLED */
+#define HAL_FLASH_MODULE_ENABLED
+/* #define HAL_NAND_MODULE_ENABLED */
+/* #define HAL_NOR_MODULE_ENABLED */
+/* #define HAL_SRAM_MODULE_ENABLED */
+/* #define HAL_SDRAM_MODULE_ENABLED */
+/* #define HAL_HASH_MODULE_ENABLED */
+#define HAL_GPIO_MODULE_ENABLED
+/* #define HAL_I2C_MODULE_ENABLED */
+/* #define HAL_I2S_MODULE_ENABLED */
+/* #define HAL_IWDG_MODULE_ENABLED */
+/* #define HAL_LPTIM_MODULE_ENABLED */
+/* #define HAL_LTDC_MODULE_ENABLED */
+#define HAL_PWR_MODULE_ENABLED
+/* #define HAL_QSPI_MODULE_ENABLED */
+#define HAL_RCC_MODULE_ENABLED
+/* #define HAL_RNG_MODULE_ENABLED */
+/* #define HAL_RTC_MODULE_ENABLED */
+/* #define HAL_SAI_MODULE_ENABLED */
+/* #define HAL_SD_MODULE_ENABLED */
+/* #define HAL_SPDIFRX_MODULE_ENABLED */
+/* #define HAL_SPI_MODULE_ENABLED */
+/* #define HAL_TIM_MODULE_ENABLED */
+#define HAL_UART_MODULE_ENABLED
+/* #define HAL_USART_MODULE_ENABLED */
+/* #define HAL_IRDA_MODULE_ENABLED */
+/* #define HAL_SMARTCARD_MODULE_ENABLED */
+/* #define HAL_WWDG_MODULE_ENABLED */
+#define HAL_CORTEX_MODULE_ENABLED
+/* #define HAL_PCD_MODULE_ENABLED */
+/* #define HAL_HCD_MODULE_ENABLED */
+/* #define HAL_DFSDM_MODULE_ENABLED */
+/* #define HAL_DSI_MODULE_ENABLED */
+/* #define HAL_JPEG_MODULE_ENABLED */
+/* #define HAL_MDIOS_MODULE_ENABLED */
+
+
+/* ########################## HSE/HSI Values adaptation ##################### */
+/**
+ * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSE is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined (HSE_STARTUP_TIMEOUT)
+ #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator (HSI) value.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSI is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+ * @brief Internal Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSI_VALUE)
+ #define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/
+#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+/**
+ * @brief External Low Speed oscillator (LSE) value.
+ */
+#if !defined (LSE_VALUE)
+ #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+#if !defined (LSE_STARTUP_TIMEOUT)
+ #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief External clock source for I2S peripheral
+ * This value is used by the I2S HAL module to compute the I2S clock source
+ * frequency, this source is inserted directly through I2S_CKIN pad.
+ */
+#if !defined (EXTERNAL_CLOCK_VALUE)
+ #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the Internal oscillator in Hz*/
+#endif /* EXTERNAL_CLOCK_VALUE */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+ === you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+ * @brief This is the HAL system configuration section
+ */
+#define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY ((uint32_t)0x0FU) /*!< tick interrupt priority */
+#define USE_RTOS 0U
+#define PREFETCH_ENABLE 1U
+#define ART_ACCLERATOR_ENABLE 1U /* To enable instruction cache and prefetch */
+
+#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */
+#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */
+#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */
+#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */
+#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */
+#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */
+#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */
+#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */
+#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */
+#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */
+#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */
+#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */
+#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */
+#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */
+#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */
+#define USE_HAL_JPEG_REGISTER_CALLBACKS 0U /* JPEG register callback disabled */
+#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */
+#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */
+#define USE_HAL_MDIOS_REGISTER_CALLBACKS 0U /* MDIOS register callback disabled */
+#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */
+#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */
+#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */
+#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */
+#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */
+#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */
+#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */
+#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */
+#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */
+#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */
+#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */
+#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */
+#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */
+#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */
+#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */
+#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */
+#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */
+#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */
+#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */
+
+/* ########################## Assert Selection ############################## */
+/**
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * HAL drivers code
+ */
+/* #define USE_FULL_ASSERT 1 */
+
+/* ################## Ethernet peripheral configuration for NUCLEO 144 board ##################### */
+
+/* Section 1 : Ethernet peripheral configuration */
+
+/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
+#define MAC_ADDR0 2U
+#define MAC_ADDR1 0U
+#define MAC_ADDR2 0U
+#define MAC_ADDR3 0U
+#define MAC_ADDR4 0U
+#define MAC_ADDR5 0U
+
+/* Definition of the Ethernet driver buffers size and count */
+#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
+#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
+#define ETH_RXBUFNB ((uint32_t)5) /* 5 Rx buffers of size ETH_RX_BUF_SIZE */
+#define ETH_TXBUFNB ((uint32_t)5) /* 5 Tx buffers of size ETH_TX_BUF_SIZE */
+
+/* Section 2: PHY configuration section */
+/* LAN8742A PHY Address*/
+#define LAN8742A_PHY_ADDRESS 0x00
+/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
+#define PHY_RESET_DELAY ((uint32_t)0x00000FFF)
+/* PHY Configuration delay */
+#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF)
+
+#define PHY_READ_TO ((uint32_t)0x0000FFFF)
+#define PHY_WRITE_TO ((uint32_t)0x0000FFFF)
+
+/* Section 3: Common PHY Registers */
+
+#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */
+#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */
+
+#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
+#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
+#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
+#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */
+#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */
+#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */
+#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */
+#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */
+#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */
+#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */
+
+#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
+#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
+#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
+
+/* Section 4: Extended PHY Registers */
+
+#define PHY_SR ((uint16_t)0x1F) /*!< PHY special control/ status register Offset */
+
+#define PHY_SPEED_STATUS ((uint16_t)0x0004) /*!< PHY Speed mask */
+#define PHY_DUPLEX_STATUS ((uint16_t)0x0010) /*!< PHY Duplex mask */
+
+
+#define PHY_ISFR ((uint16_t)0x1D) /*!< PHY Interrupt Source Flag register Offset */
+#define PHY_ISFR_INT4 ((uint16_t)0x0010) /*!< PHY Link down inturrupt */
+
+/* ################## SPI peripheral configuration ########################## */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+* Activated: CRC code is present inside driver
+* Deactivated: CRC code cleaned from driver
+*/
+
+#define USE_SPI_CRC 1U
+
+/* Includes ------------------------------------------------------------------*/
+/**
+ * @brief Include module's header file
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32f7xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32f7xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+ #include "stm32f7xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32f7xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32f7xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32f7xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
+ #include "stm32f7xx_hal_can_legacy.h"
+#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
+
+#ifdef HAL_CEC_MODULE_ENABLED
+ #include "stm32f7xx_hal_cec.h"
+#endif /* HAL_CEC_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32f7xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+ #include "stm32f7xx_hal_cryp.h"
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DMA2D_MODULE_ENABLED
+ #include "stm32f7xx_hal_dma2d.h"
+#endif /* HAL_DMA2D_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32f7xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_DCMI_MODULE_ENABLED
+ #include "stm32f7xx_hal_dcmi.h"
+#endif /* HAL_DCMI_MODULE_ENABLED */
+
+#ifdef HAL_ETH_MODULE_ENABLED
+ #include "stm32f7xx_hal_eth.h"
+#endif /* HAL_ETH_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32f7xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+ #include "stm32f7xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+ #include "stm32f7xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+ #include "stm32f7xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_SDRAM_MODULE_ENABLED
+ #include "stm32f7xx_hal_sdram.h"
+#endif /* HAL_SDRAM_MODULE_ENABLED */
+
+#ifdef HAL_HASH_MODULE_ENABLED
+ #include "stm32f7xx_hal_hash.h"
+#endif /* HAL_HASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f7xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f7xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f7xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_LPTIM_MODULE_ENABLED
+ #include "stm32f7xx_hal_lptim.h"
+#endif /* HAL_LPTIM_MODULE_ENABLED */
+
+#ifdef HAL_LTDC_MODULE_ENABLED
+ #include "stm32f7xx_hal_ltdc.h"
+#endif /* HAL_LTDC_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f7xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_QSPI_MODULE_ENABLED
+ #include "stm32f7xx_hal_qspi.h"
+#endif /* HAL_QSPI_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+ #include "stm32f7xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f7xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SAI_MODULE_ENABLED
+ #include "stm32f7xx_hal_sai.h"
+#endif /* HAL_SAI_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+ #include "stm32f7xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_SPDIFRX_MODULE_ENABLED
+ #include "stm32f7xx_hal_spdifrx.h"
+#endif /* HAL_SPDIFRX_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f7xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f7xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f7xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f7xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f7xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f7xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f7xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f7xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+ #include "stm32f7xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+#ifdef HAL_DFSDM_MODULE_ENABLED
+ #include "stm32f7xx_hal_dfsdm.h"
+#endif /* HAL_DFSDM_MODULE_ENABLED */
+
+#ifdef HAL_DSI_MODULE_ENABLED
+ #include "stm32f7xx_hal_dsi.h"
+#endif /* HAL_DSI_MODULE_ENABLED */
+
+#ifdef HAL_JPEG_MODULE_ENABLED
+ #include "stm32f7xx_hal_jpeg.h"
+#endif /* HAL_JPEG_MODULE_ENABLED */
+
+#ifdef HAL_MDIOS_MODULE_ENABLED
+ #include "stm32f7xx_hal_mdios.h"
+#endif /* HAL_MDIOS_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr: If expr is false, it calls assert_failed function
+ * which reports the name of the source file and the source
+ * line number of the call that failed.
+ * If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(uint8_t* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F7xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/hw/bsp/stm32f769disco/STM32F769ZITx_FLASH.ld b/hw/bsp/stm32f769disco/STM32F769ZITx_FLASH.ld
new file mode 100644
index 000000000..378ed80dd
--- /dev/null
+++ b/hw/bsp/stm32f769disco/STM32F769ZITx_FLASH.ld
@@ -0,0 +1,167 @@
+/*
+*****************************************************************************
+**
+
+** File : LinkerScript.ld
+**
+** Abstract : Linker script for STM32F767ZITx Device with
+** 2048KByte FLASH, 512KByte RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+**
+** Distribution: The file is distributed as is, without any warranty
+** of any kind.
+**
+** (c)Copyright Ac6.
+** You may use this file as-is or modify it according to the needs of your
+** project. Distribution of this file (unmodified or modified) is not
+** permitted. Ac6 permit registered System Workbench for MCU users the
+** rights to distribute the assembled, compiled & linked contents of this
+** file as part of an application binary file, provided that it is built
+** using the System Workbench for MCU toolchain.
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = 0x20080000; /* end of RAM */
+/* Generate a link error if heap and stack don't fit into RAM */
+_Min_Heap_Size = 0x200; /* required amount of heap */
+_Min_Stack_Size = 0x400; /* required amount of stack */
+
+/* Specify the memory areas */
+MEMORY
+{
+FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 2048K
+RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 512K
+}
+
+/* Define output sections */
+SECTIONS
+{
+ /* The startup code goes first into FLASH */
+ .isr_vector :
+ {
+ . = ALIGN(4);
+ KEEP(*(.isr_vector)) /* Startup code */
+ . = ALIGN(4);
+ } >FLASH
+
+ /* The program code and other data goes into FLASH */
+ .text :
+ {
+ . = ALIGN(4);
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ . = ALIGN(4);
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data goes into FLASH */
+ .rodata :
+ {
+ . = ALIGN(4);
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
+ .ARM : {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections goes into RAM, load LMA copy after code */
+ .data :
+ {
+ . = ALIGN(4);
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+
+ . = ALIGN(4);
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+
+ /* Uninitialized data section */
+ . = ALIGN(4);
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss secion */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ . = ALIGN(4);
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough RAM left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+
+
+ /* Remove information from the standard libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32f769disco/board.mk b/hw/bsp/stm32f769disco/board.mk
new file mode 100644
index 000000000..62c05cca5
--- /dev/null
+++ b/hw/bsp/stm32f769disco/board.mk
@@ -0,0 +1,51 @@
+CFLAGS += \
+ -flto \
+ -mthumb \
+ -mabi=aapcs \
+ -mcpu=cortex-m7 \
+ -mfloat-abi=hard \
+ -mfpu=fpv5-d16 \
+ -nostdlib -nostartfiles \
+ -DSTM32F769xx \
+ -DHSE_VALUE=25000000 \
+ -DCFG_TUSB_MCU=OPT_MCU_STM32F7 \
+ -DBOARD_DEVICE_RHPORT_NUM=1 \
+ -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED
+
+# suppress warning caused by vendor mcu driver
+CFLAGS += -Wno-error=cast-align -Wno-error=shadow
+
+ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F7xx_HAL_Driver
+ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F7xx
+
+# All source paths should be relative to the top level.
+LD_FILE = hw/bsp/$(BOARD)/STM32F769ZITx_FLASH.ld
+
+SRC_C += \
+ $(ST_CMSIS)/Source/Templates/system_stm32f7xx.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_cortex.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_rcc.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_rcc_ex.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_gpio.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_uart.c \
+ $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_pwr_ex.c
+
+SRC_S += \
+ $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f769xx.s
+
+INC += \
+ $(TOP)/hw/mcu/st/st_driver/CMSIS/Include \
+ $(TOP)/$(ST_CMSIS)/Include \
+ $(TOP)/$(ST_HAL_DRIVER)/Inc \
+ $(TOP)/hw/bsp/$(BOARD)
+
+# For TinyUSB port source
+VENDOR = st
+CHIP_FAMILY = synopsys
+
+# For freeRTOS port source
+FREERTOS_PORT = ARM_CM7/r0p1
+
+# flash target using on-board stlink
+flash: flash-stlink
diff --git a/hw/bsp/stm32f769disco/stm32f769disco.c b/hw/bsp/stm32f769disco/stm32f769disco.c
new file mode 100644
index 000000000..2664fe0e0
--- /dev/null
+++ b/hw/bsp/stm32f769disco/stm32f769disco.c
@@ -0,0 +1,297 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2020 Uwe Bonnes (bon@elektron.ikp.physik.tu-darmstadt.de),
+ * Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#include "../board.h"
+
+#include "stm32f7xx_hal.h"
+
+void OTG_FS_IRQHandler(void)
+{
+ tud_int_handler(0);
+}
+
+//--------------------------------------------------------------------+
+// Forward USB interrupt events to TinyUSB IRQ Handler
+//--------------------------------------------------------------------+
+void OTG_HS_IRQHandler(void)
+{
+ tud_int_handler(1);
+}
+
+//--------------------------------------------------------------------+
+// MACRO TYPEDEF CONSTANT ENUM
+//--------------------------------------------------------------------+
+
+#define LED_PORT GPIOJ
+#define LED_PIN GPIO_PIN_12
+#define LED_STATE_ON 5
+
+#define BUTTON_PORT GPIOA
+#define BUTTON_PIN GPIO_PIN_0
+#define BUTTON_STATE_ACTIVE 1
+
+#define UARTx USART1
+#define UART_GPIO_PORT GPIOA
+#define UART_GPIO_AF GPIO_AF7_USART1
+#define UART_TX_PIN GPIO_PIN_9
+#define UART_RX_PIN GPIO_PIN_10
+
+UART_HandleTypeDef UartHandle;
+
+// enable all LED, Button, Uart, USB clock
+static void all_rcc_clk_enable(void)
+{
+ __HAL_RCC_GPIOA_CLK_ENABLE(); // Button, UART, ULPI CLK|D0
+ __HAL_RCC_GPIOB_CLK_ENABLE(); // ULPI D1-7
+ __HAL_RCC_GPIOC_CLK_ENABLE(); // ULPI STP
+ __HAL_RCC_GPIOH_CLK_ENABLE(); // ULPI NXT
+ __HAL_RCC_GPIOI_CLK_ENABLE(); // ULPI NXT
+ __HAL_RCC_GPIOJ_CLK_ENABLE(); // LED
+ __HAL_RCC_USART1_CLK_ENABLE(); // Uart module
+}
+
+/**
+ * @brief System Clock Configuration
+ * The system Clock is configured as follow :
+ * System Clock source = PLL (HSE)
+ * SYSCLK(Hz) = 216000000
+ * HCLK(Hz) = 216000000
+ * AHB Prescaler = 1
+ * APB1 Prescaler = 4
+ * APB2 Prescaler = 2
+ * HSE Frequency(Hz) = 25000000
+ * PLL_M = HSE_VALUE/1000000
+ * PLL_N = 432
+ * PLL_P = 2
+ * PLL_Q = 9
+ * PLL_R = 7
+ * VDD(V) = 3.3
+ * Main regulator output voltage = Scale1 mode
+ * Flash Latency(WS) = 7
+ * The USB clock configuration from PLLSAI:
+ * PLLSAIP = 8
+ * PLLSAIN = 384
+ * PLLSAIQ = 7
+ * @param None
+ * @retval None
+ */
+void SystemClock_Config(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* Enable Power Control clock */
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ /* Enable HSE Oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000;
+ RCC_OscInitStruct.PLL.PLLN = 432;
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+ RCC_OscInitStruct.PLL.PLLQ = 9;
+ RCC_OscInitStruct.PLL.PLLR = 7;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ /* Activate the OverDrive to reach the 216 MHz Frequency */
+ HAL_PWREx_EnableOverDrive();
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
+
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7);
+}
+
+void board_init(void)
+{
+ SystemClock_Config();
+ all_rcc_clk_enable();
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+ // 1ms tick timer
+ SysTick_Config(SystemCoreClock / 1000);
+#endif
+
+ GPIO_InitTypeDef GPIO_InitStruct;
+
+ // LED
+ GPIO_InitStruct.Pin = LED_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
+
+ // Button
+ GPIO_InitStruct.Pin = BUTTON_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct);
+
+ // Uart
+ GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+ GPIO_InitStruct.Alternate = UART_GPIO_AF;
+ HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct);
+
+ UartHandle.Instance = UARTx;
+ UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE;
+ UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
+ UartHandle.Init.StopBits = UART_STOPBITS_1;
+ UartHandle.Init.Parity = UART_PARITY_NONE;
+ UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
+ UartHandle.Init.Mode = UART_MODE_TX_RX;
+ UartHandle.Init.OverSampling = UART_OVERSAMPLING_16;
+ HAL_UART_Init(&UartHandle);
+
+ /* Configure USB HS GPIOs */
+ /* ULPI CLK */
+ GPIO_InitStruct.Pin = GPIO_PIN_5;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* D0 */
+ GPIO_InitStruct.Pin = GPIO_PIN_3;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* D1 D2 D3 D4 D5 D6 D7 */
+ GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12 | GPIO_PIN_13 | GPIO_PIN_5;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
+ HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+ /* STP */
+ GPIO_InitStruct.Pin = GPIO_PIN_0;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
+ HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
+
+ /* NXT */
+ GPIO_InitStruct.Pin = GPIO_PIN_4;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
+ HAL_GPIO_Init(GPIOH, &GPIO_InitStruct);
+
+ /* DIR */
+ GPIO_InitStruct.Pin = GPIO_PIN_11;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS;
+ HAL_GPIO_Init(GPIOI, &GPIO_InitStruct);
+
+ // Enable ULPI clock
+ __HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE();
+
+ /* Enable USB HS Clocks */
+ __HAL_RCC_USB_OTG_HS_CLK_ENABLE();
+
+ // No VBUS sense
+ USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN;
+
+ // B-peripheral session valid override enable
+ USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN;
+ USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL;
+
+ // Force device mode
+ USB_OTG_HS->GUSBCFG &= ~USB_OTG_GUSBCFG_FHMOD;
+ USB_OTG_HS->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD;
+
+}
+
+//--------------------------------------------------------------------+
+// Board porting API
+//--------------------------------------------------------------------+
+
+void board_led_write(bool state)
+{
+ HAL_GPIO_WritePin(LED_PORT, LED_PIN, state);
+}
+
+uint32_t board_button_read(void)
+{
+ return HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN);
+}
+
+int board_uart_read(uint8_t* buf, int len)
+{
+ (void) buf; (void) len;
+ return 0;
+}
+
+int board_uart_write(void const * buf, int len)
+{
+ HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff);
+ return len;
+}
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+volatile uint32_t system_ticks = 0;
+void SysTick_Handler (void)
+{
+ system_ticks++;
+}
+
+uint32_t board_millis(void)
+{
+ return system_ticks;
+}
+#endif
+
+void HardFault_Handler (void)
+{
+ asm("bkpt");
+}
+
+// Required by __libc_init_array in startup code if we are compiling using
+// -nostdlib/-nostartfiles.
+void _init(void)
+{
+
+}
diff --git a/hw/bsp/stm32f769disco/stm32f7xx_hal_conf.h b/hw/bsp/stm32f769disco/stm32f7xx_hal_conf.h
new file mode 100644
index 000000000..03dec8f0d
--- /dev/null
+++ b/hw/bsp/stm32f769disco/stm32f7xx_hal_conf.h
@@ -0,0 +1,472 @@
+/**
+ ******************************************************************************
+ * @file stm32f7xx_hal_conf.h
+ * @author MCD Application Team
+ * @brief HAL configuration file.
+ ******************************************************************************
+ * @attention
+ *
+ * © Copyright (c) 2016 STMicroelectronics.
+ * All rights reserved.
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F7xx_HAL_CONF_H
+#define __STM32F7xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+ * @brief This is the list of modules to be used in the HAL driver
+ */
+#define HAL_MODULE_ENABLED
+/* #define HAL_ADC_MODULE_ENABLED */
+/* #define HAL_CAN_MODULE_ENABLED */
+/* #define HAL_CAN_LEGACY_MODULE_ENABLED */
+/* #define HAL_CEC_MODULE_ENABLED */
+/* #define HAL_CRC_MODULE_ENABLED */
+/* #define HAL_CRYP_MODULE_ENABLED */
+/* #define HAL_DAC_MODULE_ENABLED */
+/* #define HAL_DCMI_MODULE_ENABLED */
+#define HAL_DMA_MODULE_ENABLED
+/* #define HAL_DMA2D_MODULE_ENABLED */
+/* #define HAL_ETH_MODULE_ENABLED */
+#define HAL_FLASH_MODULE_ENABLED
+/* #define HAL_NAND_MODULE_ENABLED */
+/* #define HAL_NOR_MODULE_ENABLED */
+/* #define HAL_SRAM_MODULE_ENABLED */
+/* #define HAL_SDRAM_MODULE_ENABLED */
+/* #define HAL_HASH_MODULE_ENABLED */
+#define HAL_GPIO_MODULE_ENABLED
+/* #define HAL_I2C_MODULE_ENABLED */
+/* #define HAL_I2S_MODULE_ENABLED */
+/* #define HAL_IWDG_MODULE_ENABLED */
+/* #define HAL_LPTIM_MODULE_ENABLED */
+/* #define HAL_LTDC_MODULE_ENABLED */
+#define HAL_PWR_MODULE_ENABLED
+/* #define HAL_QSPI_MODULE_ENABLED */
+#define HAL_RCC_MODULE_ENABLED
+/* #define HAL_RNG_MODULE_ENABLED */
+/* #define HAL_RTC_MODULE_ENABLED */
+/* #define HAL_SAI_MODULE_ENABLED */
+/* #define HAL_SD_MODULE_ENABLED */
+/* #define HAL_SPDIFRX_MODULE_ENABLED */
+/* #define HAL_SPI_MODULE_ENABLED */
+/* #define HAL_TIM_MODULE_ENABLED */
+#define HAL_UART_MODULE_ENABLED
+/* #define HAL_USART_MODULE_ENABLED */
+/* #define HAL_IRDA_MODULE_ENABLED */
+/* #define HAL_SMARTCARD_MODULE_ENABLED */
+/* #define HAL_WWDG_MODULE_ENABLED */
+#define HAL_CORTEX_MODULE_ENABLED
+/* #define HAL_PCD_MODULE_ENABLED */
+/* #define HAL_HCD_MODULE_ENABLED */
+/* #define HAL_DFSDM_MODULE_ENABLED */
+/* #define HAL_DSI_MODULE_ENABLED */
+/* #define HAL_JPEG_MODULE_ENABLED */
+/* #define HAL_MDIOS_MODULE_ENABLED */
+
+
+/* ########################## HSE/HSI Values adaptation ##################### */
+/**
+ * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSE is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined (HSE_STARTUP_TIMEOUT)
+ #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator (HSI) value.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSI is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+ * @brief Internal Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSI_VALUE)
+ #define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/
+#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+/**
+ * @brief External Low Speed oscillator (LSE) value.
+ */
+#if !defined (LSE_VALUE)
+ #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+#if !defined (LSE_STARTUP_TIMEOUT)
+ #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief External clock source for I2S peripheral
+ * This value is used by the I2S HAL module to compute the I2S clock source
+ * frequency, this source is inserted directly through I2S_CKIN pad.
+ */
+#if !defined (EXTERNAL_CLOCK_VALUE)
+ #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the Internal oscillator in Hz*/
+#endif /* EXTERNAL_CLOCK_VALUE */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+ === you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+ * @brief This is the HAL system configuration section
+ */
+#define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY ((uint32_t)0x0FU) /*!< tick interrupt priority */
+#define USE_RTOS 0U
+#define PREFETCH_ENABLE 1U
+#define ART_ACCLERATOR_ENABLE 1U /* To enable instruction cache and prefetch */
+
+#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */
+#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */
+#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */
+#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */
+#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */
+#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */
+#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */
+#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */
+#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */
+#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */
+#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */
+#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */
+#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */
+#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */
+#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */
+#define USE_HAL_JPEG_REGISTER_CALLBACKS 0U /* JPEG register callback disabled */
+#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */
+#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */
+#define USE_HAL_MDIOS_REGISTER_CALLBACKS 0U /* MDIOS register callback disabled */
+#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */
+#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */
+#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */
+#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */
+#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */
+#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */
+#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */
+#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */
+#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */
+#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */
+#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */
+#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */
+#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */
+#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */
+#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */
+#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */
+#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */
+#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */
+#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */
+
+/* ########################## Assert Selection ############################## */
+/**
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * HAL drivers code
+ */
+/* #define USE_FULL_ASSERT 1 */
+
+/* ################## Ethernet peripheral configuration for NUCLEO 144 board ##################### */
+
+/* Section 1 : Ethernet peripheral configuration */
+
+/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
+#define MAC_ADDR0 2U
+#define MAC_ADDR1 0U
+#define MAC_ADDR2 0U
+#define MAC_ADDR3 0U
+#define MAC_ADDR4 0U
+#define MAC_ADDR5 0U
+
+/* Definition of the Ethernet driver buffers size and count */
+#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
+#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
+#define ETH_RXBUFNB ((uint32_t)5) /* 5 Rx buffers of size ETH_RX_BUF_SIZE */
+#define ETH_TXBUFNB ((uint32_t)5) /* 5 Tx buffers of size ETH_TX_BUF_SIZE */
+
+/* Section 2: PHY configuration section */
+/* LAN8742A PHY Address*/
+#define LAN8742A_PHY_ADDRESS 0x00
+/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
+#define PHY_RESET_DELAY ((uint32_t)0x00000FFF)
+/* PHY Configuration delay */
+#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF)
+
+#define PHY_READ_TO ((uint32_t)0x0000FFFF)
+#define PHY_WRITE_TO ((uint32_t)0x0000FFFF)
+
+/* Section 3: Common PHY Registers */
+
+#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */
+#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */
+
+#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
+#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
+#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
+#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */
+#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */
+#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */
+#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */
+#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */
+#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */
+#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */
+
+#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
+#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
+#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
+
+/* Section 4: Extended PHY Registers */
+
+#define PHY_SR ((uint16_t)0x1F) /*!< PHY special control/ status register Offset */
+
+#define PHY_SPEED_STATUS ((uint16_t)0x0004) /*!< PHY Speed mask */
+#define PHY_DUPLEX_STATUS ((uint16_t)0x0010) /*!< PHY Duplex mask */
+
+
+#define PHY_ISFR ((uint16_t)0x1D) /*!< PHY Interrupt Source Flag register Offset */
+#define PHY_ISFR_INT4 ((uint16_t)0x0010) /*!< PHY Link down inturrupt */
+
+/* ################## SPI peripheral configuration ########################## */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+* Activated: CRC code is present inside driver
+* Deactivated: CRC code cleaned from driver
+*/
+
+#define USE_SPI_CRC 1U
+
+/* Includes ------------------------------------------------------------------*/
+/**
+ * @brief Include module's header file
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32f7xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32f7xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+ #include "stm32f7xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32f7xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32f7xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32f7xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
+ #include "stm32f7xx_hal_can_legacy.h"
+#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
+
+#ifdef HAL_CEC_MODULE_ENABLED
+ #include "stm32f7xx_hal_cec.h"
+#endif /* HAL_CEC_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32f7xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+ #include "stm32f7xx_hal_cryp.h"
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DMA2D_MODULE_ENABLED
+ #include "stm32f7xx_hal_dma2d.h"
+#endif /* HAL_DMA2D_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32f7xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_DCMI_MODULE_ENABLED
+ #include "stm32f7xx_hal_dcmi.h"
+#endif /* HAL_DCMI_MODULE_ENABLED */
+
+#ifdef HAL_ETH_MODULE_ENABLED
+ #include "stm32f7xx_hal_eth.h"
+#endif /* HAL_ETH_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32f7xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+ #include "stm32f7xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+ #include "stm32f7xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+ #include "stm32f7xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_SDRAM_MODULE_ENABLED
+ #include "stm32f7xx_hal_sdram.h"
+#endif /* HAL_SDRAM_MODULE_ENABLED */
+
+#ifdef HAL_HASH_MODULE_ENABLED
+ #include "stm32f7xx_hal_hash.h"
+#endif /* HAL_HASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f7xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f7xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f7xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_LPTIM_MODULE_ENABLED
+ #include "stm32f7xx_hal_lptim.h"
+#endif /* HAL_LPTIM_MODULE_ENABLED */
+
+#ifdef HAL_LTDC_MODULE_ENABLED
+ #include "stm32f7xx_hal_ltdc.h"
+#endif /* HAL_LTDC_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f7xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_QSPI_MODULE_ENABLED
+ #include "stm32f7xx_hal_qspi.h"
+#endif /* HAL_QSPI_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+ #include "stm32f7xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f7xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SAI_MODULE_ENABLED
+ #include "stm32f7xx_hal_sai.h"
+#endif /* HAL_SAI_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+ #include "stm32f7xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_SPDIFRX_MODULE_ENABLED
+ #include "stm32f7xx_hal_spdifrx.h"
+#endif /* HAL_SPDIFRX_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f7xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f7xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f7xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f7xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f7xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f7xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f7xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f7xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+ #include "stm32f7xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+#ifdef HAL_DFSDM_MODULE_ENABLED
+ #include "stm32f7xx_hal_dfsdm.h"
+#endif /* HAL_DFSDM_MODULE_ENABLED */
+
+#ifdef HAL_DSI_MODULE_ENABLED
+ #include "stm32f7xx_hal_dsi.h"
+#endif /* HAL_DSI_MODULE_ENABLED */
+
+#ifdef HAL_JPEG_MODULE_ENABLED
+ #include "stm32f7xx_hal_jpeg.h"
+#endif /* HAL_JPEG_MODULE_ENABLED */
+
+#ifdef HAL_MDIOS_MODULE_ENABLED
+ #include "stm32f7xx_hal_mdios.h"
+#endif /* HAL_MDIOS_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr: If expr is false, it calls assert_failed function
+ * which reports the name of the source file and the source
+ * line number of the call that failed.
+ * If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(uint8_t* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F7xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/hw/bsp/stm32h743nucleo/board.mk b/hw/bsp/stm32h743nucleo/board.mk
index 30e52dfcc..43a4999a4 100644
--- a/hw/bsp/stm32h743nucleo/board.mk
+++ b/hw/bsp/stm32h743nucleo/board.mk
@@ -9,7 +9,8 @@ CFLAGS += \
-DSTM32H743xx \
-DCFG_TUSB_MCU=OPT_MCU_STM32H7
-# mcu driver cause following warnings
+# suppress warning caused by vendor mcu driver
+CFLAGS += -Wno-error=maybe-uninitialized -Wno-error=cast-align
ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32H7xx_HAL_Driver
ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32H7xx
@@ -24,6 +25,7 @@ SRC_C += \
$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_rcc.c \
$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_rcc_ex.c \
$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_gpio.c \
+ $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_uart.c \
$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_pwr_ex.c
SRC_S += \
diff --git a/hw/bsp/stm32h743nucleo/stm32h743nucleo.c b/hw/bsp/stm32h743nucleo/stm32h743nucleo.c
index bb768eb40..b4a723871 100644
--- a/hw/bsp/stm32h743nucleo/stm32h743nucleo.c
+++ b/hw/bsp/stm32h743nucleo/stm32h743nucleo.c
@@ -49,14 +49,22 @@ void OTG_FS_IRQHandler(void)
#define BUTTON_PIN GPIO_PIN_13
#define BUTTON_STATE_ACTIVE 1
+#define UARTx USART3
+#define UART_GPIO_PORT GPIOD
+#define UART_GPIO_AF GPIO_AF7_USART3
+#define UART_TX_PIN GPIO_PIN_8
+#define UART_RX_PIN GPIO_PIN_9
+
+UART_HandleTypeDef UartHandle;
+
// enable all LED, Button, Uart, USB clock
static void all_rcc_clk_enable(void)
{
__HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D-
__HAL_RCC_GPIOB_CLK_ENABLE(); // LED
__HAL_RCC_GPIOC_CLK_ENABLE(); // Button
-// __HAL_RCC_GPIOD_CLK_ENABLE(); // Uart tx, rx
-// __HAL_RCC_USART3_CLK_ENABLE(); // Uart module
+ __HAL_RCC_GPIOD_CLK_ENABLE(); // Uart tx, rx
+ __HAL_RCC_USART3_CLK_ENABLE(); // Uart module
}
/* PWR, RCC, GPIO (All): AHB4 (D3 domain)
@@ -170,6 +178,24 @@ void board_init(void)
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct);
+ // Uart
+ GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+ GPIO_InitStruct.Alternate = UART_GPIO_AF;
+ HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct);
+
+ UartHandle.Instance = UARTx;
+ UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE;
+ UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
+ UartHandle.Init.StopBits = UART_STOPBITS_1;
+ UartHandle.Init.Parity = UART_PARITY_NONE;
+ UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
+ UartHandle.Init.Mode = UART_MODE_TX_RX;
+ UartHandle.Init.OverSampling = UART_OVERSAMPLING_16;
+ HAL_UART_Init(&UartHandle);
+
// USB Pin Init
// PA9- VUSB, PA10- ID, PA11- DM, PA12- DP
@@ -226,8 +252,8 @@ int board_uart_read(uint8_t* buf, int len)
int board_uart_write(void const * buf, int len)
{
- (void) buf; (void) len;
- return 0;
+ HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff);
+ return len;
}
diff --git a/hw/bsp/stm32h743nucleo/stm32h7xx_hal_conf.h b/hw/bsp/stm32h743nucleo/stm32h7xx_hal_conf.h
index c58fdf75b..8548ca246 100644
--- a/hw/bsp/stm32h743nucleo/stm32h7xx_hal_conf.h
+++ b/hw/bsp/stm32h743nucleo/stm32h7xx_hal_conf.h
@@ -100,7 +100,7 @@
/* #define HAL_SRAM_MODULE_ENABLED */
/* #define HAL_SWPMI_MODULE_ENABLED */
/* #define HAL_TIM_MODULE_ENABLED */
-/* #define HAL_UART_MODULE_ENABLED */
+#define HAL_UART_MODULE_ENABLED */
/* #define HAL_USART_MODULE_ENABLED */
/* #define HAL_WWDG_MODULE_ENABLED */
@@ -211,6 +211,7 @@
#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */
#define USE_HAL_SWPMI_REGISTER_CALLBACKS 0U /* SWPMI register callback disabled */
#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */
+#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* USART register callback disabled */
#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */
/* ########################### Ethernet Configuration ######################### */
diff --git a/src/portable/st/synopsys/dcd_synopsys.c b/src/portable/st/synopsys/dcd_synopsys.c
index 845aecf1e..ba3cc3460 100644
--- a/src/portable/st/synopsys/dcd_synopsys.c
+++ b/src/portable/st/synopsys/dcd_synopsys.c
@@ -27,6 +27,7 @@
*/
#include "tusb_option.h"
+#include "../../../../hw/bsp//board.h"
#if defined (STM32F105x8) || defined (STM32F105xB) || defined (STM32F105xC) || \
defined (STM32F107xB) || defined (STM32F107xC)
@@ -53,33 +54,39 @@
// EP_FIFO_SIZE : Size of dedicated USB SRAM
#if CFG_TUSB_MCU == OPT_MCU_STM32F1
#include "stm32f1xx.h"
- #define EP_MAX 4
- #define EP_FIFO_SIZE 1280
+ #define EP_MAX_FS 4
+ #define EP_FIFO_SIZE_FS 1280
#elif CFG_TUSB_MCU == OPT_MCU_STM32F2
#include "stm32f2xx.h"
- #define EP_MAX USB_OTG_FS_MAX_IN_ENDPOINTS
- #define EP_FIFO_SIZE USB_OTG_FS_TOTAL_FIFO_SIZE
+ #define EP_MAX_FS USB_OTG_FS_MAX_IN_ENDPOINTS
+ #define EP_FIFO_SIZE_FS USB_OTG_FS_TOTAL_FIFO_SIZE
#elif CFG_TUSB_MCU == OPT_MCU_STM32F4
#include "stm32f4xx.h"
- #define EP_MAX USB_OTG_FS_MAX_IN_ENDPOINTS
- #define EP_FIFO_SIZE USB_OTG_FS_TOTAL_FIFO_SIZE
+ #define EP_MAX_FS USB_OTG_FS_MAX_IN_ENDPOINTS
+ #define EP_FIFO_SIZE_FS USB_OTG_FS_TOTAL_FIFO_SIZE
+ #define EP_MAX_HS USB_OTG_HS_MAX_IN_ENDPOINTS
+ #define EP_FIFO_SIZE_HS USB_OTG_HS_TOTAL_FIFO_SIZE
#elif CFG_TUSB_MCU == OPT_MCU_STM32H7
#include "stm32h7xx.h"
- #define EP_MAX 9
- #define EP_FIFO_SIZE 4096
+ #define EP_MAX_FS 9
+ #define EP_FIFO_SIZE_FS 4096
+ #define EP_MAX_HS 9
+ #define EP_FIFO_SIZE_HS 4096
#elif CFG_TUSB_MCU == OPT_MCU_STM32F7
#include "stm32f7xx.h"
- #define EP_MAX 6
- #define EP_FIFO_SIZE 1280
+ #define EP_MAX_FS 6
+ #define EP_FIFO_SIZE_FS 1280
+ #define EP_MAX_HS 9
+ #define EP_FIFO_SIZE_HS 4096
#elif CFG_TUSB_MCU == OPT_MCU_STM32L4
#include "stm32l4xx.h"
- #define EP_MAX 6
- #define EP_FIFO_SIZE 1280
+ #define EP_MAX_FS 6
+ #define EP_FIFO_SIZE_FS 1280
#else
#error "Unsupported MCUs"
@@ -140,6 +147,13 @@ typedef struct {
typedef volatile uint32_t * usb_fifo_t;
+#if TUD_OPT_RHPORT == 1
+# define EP_MAX EP_MAX_HS
+# define EP_FIFO_SIZE EP_FIFO_SIZE_HS
+#else
+# define EP_MAX EP_MAX_FS
+# define EP_FIFO_SIZE EP_FIFO_SIZE_FS
+#endif
xfer_ctl_t xfer_status[EP_MAX][2];
#define XFER_CTL_BASE(_ep, _dir) &xfer_status[_ep][_dir]
@@ -287,6 +301,59 @@ static void edpt_schedule_packets(uint8_t rhport, uint8_t const epnum, uint8_t c
}
+# if defined(USB_HS_PHYC) && TUD_OPT_HIGH_SPEED
+static bool USB_HS_PHYCInit(void)
+{
+ USB_HS_PHYC_GlobalTypeDef *usb_hs_phyc = (USB_HS_PHYC_GlobalTypeDef *)USB_HS_PHYC_CONTROLLER_BASE;
+ // Enable LDO
+ usb_hs_phyc->USB_HS_PHYC_LDO |= USB_HS_PHYC_LDO_ENABLE;
+ int32_t count = 2000000;
+ while(1) {
+ if (usb_hs_phyc->USB_HS_PHYC_LDO & USB_HS_PHYC_LDO_STATUS)
+ break;
+ TU_ASSERT(count > 0);
+ }
+ uint32_t phyc_pll = 0;
+ switch (HSE_VALUE) {
+ case 12000000:
+ phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_12MHZ;
+ break;
+ case 12500000:
+ phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_12_5MHZ;
+ break;
+ case 16000000:
+ phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_16MHZ;
+ break;
+ case 24000000:
+ phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_24MHZ;
+ break;
+ case 25000000:
+ phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_25MHZ;
+ break;
+ case 32000000:
+ // Value not defined in header
+ phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_Msk;
+ break;
+ default:
+ TU_ASSERT(0);
+ }
+ usb_hs_phyc->USB_HS_PHYC_PLL = phyc_pll;
+
+ // Use magic value as in stm32f7xx_ll_usb.
+# if !defined (USB_HS_PHYC_TUNE_VALUE)
+# define USB_HS_PHYC_TUNE_VALUE 0x00000F13U /*!< Value of USB HS PHY Tune */
+# endif /* USB_HS_PHYC_TUNE_VALUE */
+ // Control the tuning interface of the High Speed PHY */
+ usb_hs_phyc->USB_HS_PHYC_TUNE |= USB_HS_PHYC_TUNE_VALUE;
+
+ // Enable PLL internal PHY
+ usb_hs_phyc->USB_HS_PHYC_PLL = phyc_pll | USB_HS_PHYC_PLL_PLLEN;
+
+ board_delay(2);
+ return true;
+}
+# endif
+
/*------------------------------------------------------------------*/
/* Controller API
*------------------------------------------------------------------*/
@@ -301,12 +368,31 @@ void dcd_init (uint8_t rhport)
#if TUD_OPT_HIGH_SPEED // TODO may pass parameter instead of using macro for HighSpeed
if ( rhport == 1 )
{
- // Highspeed with external ULPI PHY
-
// deactivate internal PHY
usb_otg->GCCFG &= ~USB_OTG_GCCFG_PWRDWN;
- // On selected MCUs HS port1 can be used with external PHY via ULPI interface
+ // TODO may pass parameter instead of using macro for HighSpeed
+#if defined(USB_HS_PHYC)
+ // Highspeed with embedded UTMI PHYC
+ // Init The UTMI Interface
+ usb_otg->GUSBCFG &= ~(USB_OTG_GUSBCFG_TSDPS | USB_OTG_GUSBCFG_ULPIFSLS | USB_OTG_GUSBCFG_PHYSEL);
+
+ // Select vbus source
+ usb_otg->GUSBCFG &= ~(USB_OTG_GUSBCFG_ULPIEVBUSD | USB_OTG_GUSBCFG_ULPIEVBUSI);
+
+ // Select UTMI Interace
+ usb_otg->GUSBCFG &= ~USB_OTG_GUSBCFG_ULPI_UTMI_SEL;
+ usb_otg->GCCFG |= USB_OTG_GCCFG_PHYHSEN;
+
+ //Enables control of a High Speed USB PHY
+ USB_HS_PHYCInit();
+
+ // Disable external VBUS detection
+ usb_otg->GUSBCFG &= ~USB_OTG_GUSBCFG_ULPIEVBUSD;
+
+# else// On selected MCUs HS port1 can be used with external PHY via ULPI interface
+ // Highspeed with external ULPI PHY
+
// Init ULPI Interface
usb_otg->GUSBCFG &= ~(USB_OTG_GUSBCFG_TSDPS | USB_OTG_GUSBCFG_ULPIFSLS | USB_OTG_GUSBCFG_PHYSEL);
@@ -314,6 +400,7 @@ void dcd_init (uint8_t rhport)
usb_otg->GUSBCFG &= ~(USB_OTG_GUSBCFG_ULPIEVBUSD | USB_OTG_GUSBCFG_ULPIEVBUSI);
set_turnaround(usb_otg, TUSB_SPEED_HIGH);
+# endif
}
else
#endif