diff --git a/examples/device/cdc_msc_hid/ses/stm32f4/stm32f4.emProject b/examples/device/cdc_msc_hid/ses/stm32f4/stm32f4.emProject
index 83067fd09..6f6690d21 100644
--- a/examples/device/cdc_msc_hid/ses/stm32f4/stm32f4.emProject
+++ b/examples/device/cdc_msc_hid/ses/stm32f4/stm32f4.emProject
@@ -61,8 +61,8 @@
recurse="No" />
-
-
+
+
@@ -76,11 +76,11 @@
diff --git a/examples/device/midi_test/src/usb_descriptors.c b/examples/device/midi_test/src/usb_descriptors.c
index 192dacfbe..3eef02bb2 100644
--- a/examples/device/midi_test/src/usb_descriptors.c
+++ b/examples/device/midi_test/src/usb_descriptors.c
@@ -71,10 +71,13 @@ enum
CONFIG_TOTAL_LEN = TUD_CONFIG_DESC_LEN + TUD_MIDI_DESC_LEN
};
-// Use Endpoint 2 instead of 1 due to NXP MCU
-// LPC 17xx and 40xx endpoint type (bulk/interrupt/iso) are fixed by its number
-// 0 control, 1 In, 2 Bulk, 3 Iso, 4 In etc ...
-#define EPNUM_MIDI 0x02
+#if CFG_TUSB_MCU == OPT_MCU_LPC175X_6X || CFG_TUSB_MCU == OPT_MCU_LPC177X_8X || CFG_TUSB_MCU == OPT_MCU_LPC40XX
+ // LPC 17xx and 40xx endpoint type (bulk/interrupt/iso) are fixed by its number
+ // 0 control, 1 In, 2 Bulk, 3 Iso, 4 In etc ...
+ #define EPNUM_MIDI 0x02
+#else
+ #define EPNUM_MIDI 0x01
+#endif
uint8_t const desc_configuration[] =
{
diff --git a/examples/device/msc_dual_lun/src/usb_descriptors.c b/examples/device/msc_dual_lun/src/usb_descriptors.c
index 26ebe190c..1a71b7fcc 100644
--- a/examples/device/msc_dual_lun/src/usb_descriptors.c
+++ b/examples/device/msc_dual_lun/src/usb_descriptors.c
@@ -68,10 +68,13 @@ enum
CONFIG_TOTAL_LEN = TUD_CONFIG_DESC_LEN + TUD_MSC_DESC_LEN
};
-// Use Endpoint 2 instead of 1 due to NXP MCU
-// LPC 17xx and 40xx endpoint type (bulk/interrupt/iso) are fixed by its number
-// 0 control, 1 In, 2 Bulk, 3 Iso, 4 In etc ...
-#define EPNUM_MSC 0x02
+#if CFG_TUSB_MCU == OPT_MCU_LPC175X_6X || CFG_TUSB_MCU == OPT_MCU_LPC177X_8X || CFG_TUSB_MCU == OPT_MCU_LPC40XX
+ // LPC 17xx and 40xx endpoint type (bulk/interrupt/iso) are fixed by its number
+ // 0 control, 1 In, 2 Bulk, 3 Iso, 4 In etc ...
+ #define EPNUM_MSC 0x02
+#else
+ #define EPNUM_MSC 0x01
+#endif
uint8_t const desc_configuration[] =
{
diff --git a/hw/bsp/stm32f303disc/STM32F303VCTx_FLASH.ld b/hw/bsp/stm32f303disco/STM32F303VCTx_FLASH.ld
similarity index 100%
rename from hw/bsp/stm32f303disc/STM32F303VCTx_FLASH.ld
rename to hw/bsp/stm32f303disco/STM32F303VCTx_FLASH.ld
diff --git a/hw/bsp/stm32f303disc/board.mk b/hw/bsp/stm32f303disco/board.mk
similarity index 93%
rename from hw/bsp/stm32f303disc/board.mk
rename to hw/bsp/stm32f303disco/board.mk
index 76922a46a..7a493c244 100644
--- a/hw/bsp/stm32f303disc/board.mk
+++ b/hw/bsp/stm32f303disco/board.mk
@@ -10,7 +10,7 @@ CFLAGS += \
-nostdlib -nostartfiles
# All source paths should be relative to the top level.
-LD_FILE = hw/bsp/stm32f303disc/STM32F303VCTx_FLASH.ld
+LD_FILE = hw/bsp/stm32f303disco/STM32F303VCTx_FLASH.ld
SRC_C += \
hw/mcu/st/system-init/system_stm32f3xx.c \
@@ -23,7 +23,7 @@ SRC_S += \
hw/mcu/st/startup/stm32f3/startup_stm32f303xc.s
INC += \
- $(TOP)/hw/bsp/stm32f303disc \
+ $(TOP)/hw/bsp/stm32f303disco \
$(TOP)/hw/mcu/st/cmsis \
$(TOP)/hw/mcu/st/stm32lib/CMSIS/STM32F3xx/Include \
$(TOP)/hw/mcu/st/stm32lib/STM32F3xx_HAL_Driver/Inc
diff --git a/hw/bsp/stm32f303disc/board_stm32f303disc.c b/hw/bsp/stm32f303disco/board_stm32f303disco.c
similarity index 91%
rename from hw/bsp/stm32f303disc/board_stm32f303disc.c
rename to hw/bsp/stm32f303disco/board_stm32f303disco.c
index 9a103ac60..c5e1108eb 100644
--- a/hw/bsp/stm32f303disc/board_stm32f303disc.c
+++ b/hw/bsp/stm32f303disco/board_stm32f303disco.c
@@ -29,8 +29,17 @@
#include "stm32f3xx.h"
#include "stm32f3xx_hal_conf.h"
+#define LED_PORT GPIOE
+#define LED_PIN GPIO_PIN_9
+
void board_init(void)
{
+ #if CFG_TUSB_OS == OPT_OS_NONE
+ // 1ms tick timer
+ SysTick_Config(SystemCoreClock / 1000);
+ #endif
+
+ /* Configure the system clock to 72 MHz */
RCC_ClkInitTypeDef RCC_ClkInitStruct;
RCC_OscInitTypeDef RCC_OscInitStruct;
@@ -55,22 +64,18 @@ void board_init(void)
// Notify runtime of frequency change.
SystemCoreClockUpdate();
- #if CFG_TUSB_OS == OPT_OS_NONE
- // 1ms tick timer
- SysTick_Config(SystemCoreClock / 1000);
- #endif
-
- /* -1- Enable GPIOE Clock (to be able to program the configuration registers) */
+ /* -1- Enable GPIO Clock (to be able to program the configuration registers) */
__HAL_RCC_GPIOE_CLK_ENABLE();
/* -2- Configure PE.8 to PE.15 IOs in output push-pull mode to drive external LEDs */
- static GPIO_InitTypeDef GPIO_InitStruct;
- GPIO_InitStruct.Pin = GPIO_PIN_9;
+ GPIO_InitTypeDef GPIO_InitStruct;
+ GPIO_InitStruct.Pin = LED_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
- HAL_GPIO_Init(GPIOE, &GPIO_InitStruct);
+ board_led_write(false);
#if 0
RCC->AHB2ENR |= RCC_AHB2ENR_OTGFSEN;
@@ -97,7 +102,7 @@ void board_init(void)
void board_led_write(bool state)
{
- HAL_GPIO_WritePin(GPIOE, GPIO_PIN_9, state);
+ HAL_GPIO_WritePin(LED_PORT, LED_PIN, state);
}
uint32_t board_button_read(void)
diff --git a/hw/bsp/stm32f303disc/stm32f3xx_hal_conf.h b/hw/bsp/stm32f303disco/stm32f3xx_hal_conf.h
similarity index 100%
rename from hw/bsp/stm32f303disc/stm32f3xx_hal_conf.h
rename to hw/bsp/stm32f303disco/stm32f3xx_hal_conf.h
diff --git a/hw/bsp/stm32f407g_disc1/STM32F407VGTx_FLASH.ld b/hw/bsp/stm32f407disco/STM32F407VGTx_FLASH.ld
similarity index 100%
rename from hw/bsp/stm32f407g_disc1/STM32F407VGTx_FLASH.ld
rename to hw/bsp/stm32f407disco/STM32F407VGTx_FLASH.ld
diff --git a/hw/bsp/stm32f407g_disc1/board.mk b/hw/bsp/stm32f407disco/board.mk
similarity index 63%
rename from hw/bsp/stm32f407g_disc1/board.mk
rename to hw/bsp/stm32f407disco/board.mk
index ab3043a40..bc1fd7c70 100644
--- a/hw/bsp/stm32f407g_disc1/board.mk
+++ b/hw/bsp/stm32f407disco/board.mk
@@ -10,17 +10,23 @@ CFLAGS += \
-DCFG_TUSB_MCU=OPT_MCU_STM32F4
# All source paths should be relative to the top level.
-LD_FILE = hw/bsp/stm32f407g_disc1/STM32F407VGTx_FLASH.ld
+LD_FILE = hw/bsp/stm32f407disco/STM32F407VGTx_FLASH.ld
SRC_C += \
- hw/mcu/st/system-init/system_stm32f4xx.c
+ hw/mcu/st/system-init/system_stm32f4xx.c \
+ hw/mcu/st/stm32lib/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal.c \
+ hw/mcu/st/stm32lib/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_cortex.c \
+ hw/mcu/st/stm32lib/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc.c \
+ hw/mcu/st/stm32lib/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_gpio.c
SRC_S += \
hw/mcu/st/startup/stm32f4/startup_stm32f407xx.s
INC += \
+ $(TOP)/hw/mcu/st/cmsis \
$(TOP)/hw/mcu/st/stm32lib/CMSIS/STM32F4xx/Include \
- $(TOP)/hw/mcu/st/cmsis
+ $(TOP)/hw/mcu/st/stm32lib/STM32F4xx_HAL_Driver/Inc \
+ $(TOP)/hw/bsp/stm32f407disco
# For TinyUSB port source
VENDOR = st
diff --git a/hw/bsp/stm32f407disco/board_stm32f407disco.c b/hw/bsp/stm32f407disco/board_stm32f407disco.c
new file mode 100644
index 000000000..6936f2b12
--- /dev/null
+++ b/hw/bsp/stm32f407disco/board_stm32f407disco.c
@@ -0,0 +1,188 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2019 Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#include "../board.h"
+
+#include "stm32f4xx.h"
+#include "stm32f4xx_hal_conf.h"
+
+#define LED_PORT GPIOD
+#define LED_PIN GPIO_PIN_14
+
+/**
+ * @brief System Clock Configuration
+ * The system Clock is configured as follow :
+ * System Clock source = PLL (HSE)
+ * SYSCLK(Hz) = 168000000
+ * HCLK(Hz) = 168000000
+ * AHB Prescaler = 1
+ * APB1 Prescaler = 4
+ * APB2 Prescaler = 2
+ * HSE Frequency(Hz) = 8000000
+ * PLL_M = 8
+ * PLL_N = 336
+ * PLL_P = 2
+ * PLL_Q = 7
+ * VDD(V) = 3.3
+ * Main regulator output voltage = Scale1 mode
+ * Flash Latency(WS) = 5
+ * @param None
+ * @retval None
+ */
+static void SystemClock_Config(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* Enable Power Control clock */
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ /* Enable HSE Oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 8;
+ RCC_OscInitStruct.PLL.PLLN = 336;
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+ RCC_OscInitStruct.PLL.PLLQ = 7;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2
+ clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
+}
+
+void board_init(void)
+{
+#if CFG_TUSB_OS == OPT_OS_NONE
+ // 1ms tick timer
+ SysTick_Config(SystemCoreClock / 1000);
+#elif CFG_TUSB_OS == OPT_OS_FREERTOS
+ // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher )
+ //NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY );
+#endif
+
+ SystemClock_Config();
+
+ // Notify runtime of frequency change.
+ SystemCoreClockUpdate();
+
+ // Enable USB OTG clock
+ __HAL_RCC_USB_OTG_FS_CLK_ENABLE();
+
+ GPIO_InitTypeDef GPIO_InitStruct;
+
+ // USB Pin Init
+ // PA9- VUSB, PA10- ID, PA11- DM, PA12- DP
+ __HAL_RCC_GPIOA_CLK_ENABLE();
+
+ /* Configure DM DP Pins */
+ GPIO_InitStruct.Pin = GPIO_PIN_11 | GPIO_PIN_12;
+ GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* Configure VBUS Pin */
+ GPIO_InitStruct.Pin = GPIO_PIN_9;
+ GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* This for ID line debug */
+ GPIO_InitStruct.Pin = GPIO_PIN_10;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_OD;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ // Init the LED
+ __HAL_RCC_GPIOD_CLK_ENABLE();
+
+ GPIO_InitStruct.Pin = LED_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FAST;
+ HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
+
+ board_led_write(false);
+
+ // TODO Button
+}
+
+//--------------------------------------------------------------------+
+// Board porting API
+//--------------------------------------------------------------------+
+
+void board_led_write(bool state)
+{
+ HAL_GPIO_WritePin(LED_PORT, LED_PIN, state);
+}
+
+uint32_t board_button_read(void)
+{
+ // TODO implement
+ return 0;
+}
+
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+volatile uint32_t system_ticks = 0;
+void SysTick_Handler (void)
+{
+ system_ticks++;
+}
+
+uint32_t board_millis(void)
+{
+ return system_ticks;
+}
+#endif
+
+void HardFault_Handler (void)
+{
+ asm("bkpt");
+}
+
+// Required by __libc_init_array in startup code if we are compiling using
+// -nostdlib/-nostartfiles.
+void _init(void)
+{
+
+}
diff --git a/hw/bsp/stm32f407disco/stm32f4xx_hal_conf.h b/hw/bsp/stm32f407disco/stm32f4xx_hal_conf.h
new file mode 100644
index 000000000..d9a690041
--- /dev/null
+++ b/hw/bsp/stm32f407disco/stm32f4xx_hal_conf.h
@@ -0,0 +1,394 @@
+/**
+ ******************************************************************************
+ * @file GPIO/GPIO_EXTI/Inc/stm32f4xx_hal_conf.h
+ * @author MCD Application Team
+ * @brief HAL configuration file
+ ******************************************************************************
+ * @attention
+ *
+ *
© COPYRIGHT(c) 2017 STMicroelectronics
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F4xx_HAL_CONF_H
+#define __STM32F4xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+ * @brief This is the list of modules to be used in the HAL driver
+ */
+#define HAL_MODULE_ENABLED
+/* #define HAL_ADC_MODULE_ENABLED */
+/* #define HAL_CAN_MODULE_ENABLED */
+/* #define HAL_CAN_LEGACY_MODULE_ENABLED */
+/* #define HAL_CRC_MODULE_ENABLED */
+/* #define HAL_CRYP_MODULE_ENABLED */
+/* #define HAL_DAC_MODULE_ENABLED */
+/* #define HAL_DCMI_MODULE_ENABLED */
+#define HAL_DMA_MODULE_ENABLED
+/* #define HAL_DMA2D_MODULE_ENABLED */
+/* #define HAL_ETH_MODULE_ENABLED */
+#define HAL_FLASH_MODULE_ENABLED
+/* #define HAL_NAND_MODULE_ENABLED */
+/* #define HAL_NOR_MODULE_ENABLED */
+/* #define HAL_PCCARD_MODULE_ENABLED */
+/* #define HAL_SRAM_MODULE_ENABLED */
+/* #define HAL_SDRAM_MODULE_ENABLED */
+/* #define HAL_HASH_MODULE_ENABLED */
+#define HAL_GPIO_MODULE_ENABLED
+// #define HAL_I2C_MODULE_ENABLED
+/* #define HAL_I2S_MODULE_ENABLED */
+/* #define HAL_IWDG_MODULE_ENABLED */
+/* #define HAL_LTDC_MODULE_ENABLED */
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+/* #define HAL_RNG_MODULE_ENABLED */
+/* #define HAL_RTC_MODULE_ENABLED */
+/* #define HAL_SAI_MODULE_ENABLED */
+/* #define HAL_SD_MODULE_ENABLED */
+// #define HAL_SPI_MODULE_ENABLED
+/* #define HAL_TIM_MODULE_ENABLED */
+/* #define HAL_UART_MODULE_ENABLED */
+/* #define HAL_USART_MODULE_ENABLED */
+/* #define HAL_IRDA_MODULE_ENABLED */
+/* #define HAL_SMARTCARD_MODULE_ENABLED */
+/* #define HAL_WWDG_MODULE_ENABLED */
+#define HAL_CORTEX_MODULE_ENABLED
+/* #define HAL_PCD_MODULE_ENABLED */
+/* #define HAL_HCD_MODULE_ENABLED */
+
+
+/* ########################## HSE/HSI Values adaptation ##################### */
+/**
+ * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSE is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE (8000000U) /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined (HSE_STARTUP_TIMEOUT)
+ #define HSE_STARTUP_TIMEOUT (100U) /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator (HSI) value.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSI is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE (16000000U) /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+ * @brief Internal Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSI_VALUE)
+ #define LSI_VALUE (32000U)
+#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+/**
+ * @brief External Low Speed oscillator (LSE) value.
+ */
+#if !defined (LSE_VALUE)
+ #define LSE_VALUE (32768U) /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+#if !defined (LSE_STARTUP_TIMEOUT)
+ #define LSE_STARTUP_TIMEOUT (5000U) /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief External clock source for I2S peripheral
+ * This value is used by the I2S HAL module to compute the I2S clock source
+ * frequency, this source is inserted directly through I2S_CKIN pad.
+ */
+#if !defined (EXTERNAL_CLOCK_VALUE)
+ #define EXTERNAL_CLOCK_VALUE (12288000U) /*!< Value of the External oscillator in Hz*/
+#endif /* EXTERNAL_CLOCK_VALUE */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+ === you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+ * @brief This is the HAL system configuration section
+ */
+#define VDD_VALUE (3300U) /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY (0x0FU) /*!< tick interrupt priority */
+#define USE_RTOS 0U
+#define PREFETCH_ENABLE 1U
+#define INSTRUCTION_CACHE_ENABLE 1U
+#define DATA_CACHE_ENABLE 1U
+
+#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */
+#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */
+#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */
+#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */
+#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */
+#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */
+#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */
+#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */
+#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */
+#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */
+#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */
+#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */
+#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */
+#define USE_HAL_FMPI2C_REGISTER_CALLBACKS 0U /* FMPI2C register callback disabled */
+#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */
+#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */
+#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */
+#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */
+#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */
+#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */
+#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */
+#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */
+#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */
+#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */
+#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */
+#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */
+#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */
+#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */
+#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */
+#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */
+#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */
+#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */
+#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */
+#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */
+#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */
+#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */
+#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */
+#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */
+
+/* ########################## Assert Selection ############################## */
+/**
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * HAL drivers code
+ */
+/* #define USE_FULL_ASSERT 1U */
+
+/* ################## SPI peripheral configuration ########################## */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+* Activated: CRC code is present inside driver
+* Deactivated: CRC code cleaned from driver
+*/
+
+#define USE_SPI_CRC 1U
+
+/* Includes ------------------------------------------------------------------*/
+/**
+ * @brief Include module's header file
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32f4xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32f4xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+ #include "stm32f4xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32f4xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32f4xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32f4xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
+ #include "stm32f4xx_hal_can_legacy.h"
+#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32f4xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+ #include "stm32f4xx_hal_cryp.h"
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DMA2D_MODULE_ENABLED
+ #include "stm32f4xx_hal_dma2d.h"
+#endif /* HAL_DMA2D_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32f4xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_DCMI_MODULE_ENABLED
+ #include "stm32f4xx_hal_dcmi.h"
+#endif /* HAL_DCMI_MODULE_ENABLED */
+
+#ifdef HAL_ETH_MODULE_ENABLED
+ #include "stm32f4xx_hal_eth.h"
+#endif /* HAL_ETH_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32f4xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+ #include "stm32f4xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+ #include "stm32f4xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+ #include "stm32f4xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_PCCARD_MODULE_ENABLED
+ #include "stm32f4xx_hal_pccard.h"
+#endif /* HAL_PCCARD_MODULE_ENABLED */
+
+#ifdef HAL_SDRAM_MODULE_ENABLED
+ #include "stm32f4xx_hal_sdram.h"
+#endif /* HAL_SDRAM_MODULE_ENABLED */
+
+#ifdef HAL_HASH_MODULE_ENABLED
+ #include "stm32f4xx_hal_hash.h"
+#endif /* HAL_HASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f4xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f4xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f4xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_LTDC_MODULE_ENABLED
+ #include "stm32f4xx_hal_ltdc.h"
+#endif /* HAL_LTDC_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f4xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+ #include "stm32f4xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f4xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SAI_MODULE_ENABLED
+ #include "stm32f4xx_hal_sai.h"
+#endif /* HAL_SAI_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+ #include "stm32f4xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f4xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f4xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f4xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f4xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f4xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f4xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f4xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f4xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+ #include "stm32f4xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr: If expr is false, it calls assert_failed function
+ * which reports the name of the source file and the source
+ * line number of the call that failed.
+ * If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(uint8_t* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F4xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/hw/bsp/stm32f407g_disc1/board_stm32f407g_disc1.c b/hw/bsp/stm32f407g_disc1/board_stm32f407g_disc1.c
deleted file mode 100644
index c5695733c..000000000
--- a/hw/bsp/stm32f407g_disc1/board_stm32f407g_disc1.c
+++ /dev/null
@@ -1,132 +0,0 @@
-/*
- * The MIT License (MIT)
- *
- * Copyright (c) 2019 Ha Thach (tinyusb.org)
- *
- * Permission is hereby granted, free of charge, to any person obtaining a copy
- * of this software and associated documentation files (the "Software"), to deal
- * in the Software without restriction, including without limitation the rights
- * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
- * copies of the Software, and to permit persons to whom the Software is
- * furnished to do so, subject to the following conditions:
- *
- * The above copyright notice and this permission notice shall be included in
- * all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
- * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
- * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
- * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
- * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
- * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
- * THE SOFTWARE.
- *
- * This file is part of the TinyUSB stack.
- */
-
-#include "../board.h"
-
-#include "stm32f4xx.h"
-
-void board_init(void)
-{
- // Init the LED on PD14
- RCC->AHB1ENR |= RCC_AHB1ENR_GPIODEN;
- GPIOD->MODER |= GPIO_MODER_MODE14_0;
-
- // TODO Button
-
- // USB Clock init
- // PLL input- 8 MHz (External oscillator clock; HSI clock tolerance isn't
- // tight enough- 1%, need 0.25%)
- // VCO input- 1 to 2 MHz (2 MHz, M = 4)
- // VCO output- 100 to 432 MHz (144 MHz, N = 72)
- // Main PLL out- <= 180 MHz (18 MHz, P = 3- divides by 8)
- // USB PLL out- 48 MHz (Q = 3)
- RCC->PLLCFGR = RCC_PLLCFGR_PLLSRC_HSE | (3 << RCC_PLLCFGR_PLLQ_Pos) | \
- (3 << RCC_PLLCFGR_PLLP_Pos) | (72 << RCC_PLLCFGR_PLLN_Pos) | \
- (4 << RCC_PLLCFGR_PLLM_Pos);
-
- // Wait for external clock to become ready
- RCC->CR |= RCC_CR_HSEON;
- while(!(RCC->CR & RCC_CR_HSERDY_Msk));
-
- // Wait for PLL to become ready
- RCC->CR |= RCC_CR_PLLON;
- while(!(RCC->CR & RCC_CR_PLLRDY_Msk));
-
- // Switch clocks!
- RCC->CFGR |= RCC_CFGR_SW_1;
-
- // Notify runtime of frequency change.
- SystemCoreClockUpdate();
-
-#if CFG_TUSB_OS == OPT_OS_NONE
- // 1ms tick timer
- SysTick_Config(SystemCoreClock / 1000);
-#elif CFG_TUSB_OS == OPT_OS_FREERTOS
- // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher )
- //NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY );
-#endif
-
- RCC->AHB2ENR |= RCC_AHB2ENR_OTGFSEN;
-
- // USB Pin Init
- // PA9- VUSB, PA10- ID, PA11- DM, PA12- DP
- // PC0- Power on
- RCC->AHB1ENR |= RCC_AHB1ENR_GPIOAEN;
- GPIOA->MODER |= GPIO_MODER_MODE9_1 | GPIO_MODER_MODE10_1 | \
- GPIO_MODER_MODE11_1 | GPIO_MODER_MODE12_1;
- GPIOA->AFR[1] |= (10 << GPIO_AFRH_AFSEL9_Pos) | \
- (10 << GPIO_AFRH_AFSEL10_Pos) | (10 << GPIO_AFRH_AFSEL11_Pos) | \
- (10 << GPIO_AFRH_AFSEL12_Pos);
-
- // Pullup required on ID, despite the manual claiming there's an
- // internal pullup already (page 1245, Rev 17)
- GPIOA->PUPDR |= GPIO_PUPDR_PUPD10_0;
-}
-
-//--------------------------------------------------------------------+
-// Board porting API
-//--------------------------------------------------------------------+
-
-void board_led_write(bool state)
-{
- if (!state) {
- GPIOD->BSRR = GPIO_BSRR_BR14;
- } else {
- GPIOD->BSRR = GPIO_BSRR_BS14;
- }
-}
-
-uint32_t board_button_read(void)
-{
- // TODO implement
- return 0;
-}
-
-
-#if CFG_TUSB_OS == OPT_OS_NONE
-volatile uint32_t system_ticks = 0;
-void SysTick_Handler (void)
-{
- system_ticks++;
-}
-
-uint32_t board_millis(void)
-{
- return system_ticks;
-}
-#endif
-
-void HardFault_Handler (void)
-{
- asm("bkpt");
-}
-
-// Required by __libc_init_array in startup code if we are compiling using
-// -nostdlib/-nostartfiles.
-void _init(void)
-{
-
-}
diff --git a/hw/bsp/stm32f411disco/STM32F411VETx_FLASH.ld b/hw/bsp/stm32f411disco/STM32F411VETx_FLASH.ld
new file mode 100644
index 000000000..3a0ce526f
--- /dev/null
+++ b/hw/bsp/stm32f411disco/STM32F411VETx_FLASH.ld
@@ -0,0 +1,169 @@
+/*
+*****************************************************************************
+**
+
+** File : LinkerScript.ld
+**
+** Abstract : Linker script for STM32F411VETx Device with
+** 512KByte FLASH, 128KByte RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+**
+** Distribution: The file is distributed as is, without any warranty
+** of any kind.
+**
+** (c)Copyright Ac6.
+** You may use this file as-is or modify it according to the needs of your
+** project. Distribution of this file (unmodified or modified) is not
+** permitted. Ac6 permit registered System Workbench for MCU users the
+** rights to distribute the assembled, compiled & linked contents of this
+** file as part of an application binary file, provided that it is built
+** using the System Workbench for MCU toolchain.
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = 0x20020000; /* end of RAM */
+/* Generate a link error if heap and stack don't fit into RAM */
+_Min_Heap_Size = 0x200;; /* required amount of heap */
+_Min_Stack_Size = 0x400;; /* required amount of stack */
+
+/* Specify the memory areas */
+MEMORY
+{
+FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 512K
+RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K
+}
+
+/* Define output sections */
+SECTIONS
+{
+ /* The startup code goes first into FLASH */
+ .isr_vector :
+ {
+ . = ALIGN(4);
+ KEEP(*(.isr_vector)) /* Startup code */
+ . = ALIGN(4);
+ } >FLASH
+
+ /* The program code and other data goes into FLASH */
+ .text :
+ {
+ . = ALIGN(4);
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ . = ALIGN(4);
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data goes into FLASH */
+ .rodata :
+ {
+ . = ALIGN(4);
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
+ .ARM : {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections goes into RAM, load LMA copy after code */
+ .data :
+ {
+ . = ALIGN(4);
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+
+ . = ALIGN(4);
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+
+ /* Uninitialized data section */
+ . = ALIGN(4);
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss secion */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ . = ALIGN(4);
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough RAM left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+
+
+ /* Remove information from the standard libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
+
+
diff --git a/hw/bsp/stm32f411disco/board.mk b/hw/bsp/stm32f411disco/board.mk
new file mode 100644
index 000000000..8154545f7
--- /dev/null
+++ b/hw/bsp/stm32f411disco/board.mk
@@ -0,0 +1,47 @@
+CFLAGS += \
+ -DHSE_VALUE=8000000 \
+ -DCFG_TUSB_MCU=OPT_MCU_STM32F4 \
+ -DSTM32F411xE \
+ -mthumb \
+ -mabi=aapcs-linux \
+ -mcpu=cortex-m4 \
+ -mfloat-abi=hard \
+ -mfpu=fpv4-sp-d16 \
+ -nostdlib -nostartfiles
+
+# All source paths should be relative to the top level.
+LD_FILE = hw/bsp/stm32f411disco/STM32F411VETx_FLASH.ld
+
+SRC_C += \
+ hw/mcu/st/system-init/system_stm32f4xx.c \
+ hw/mcu/st/stm32lib/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal.c \
+ hw/mcu/st/stm32lib/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_cortex.c \
+ hw/mcu/st/stm32lib/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc.c \
+ hw/mcu/st/stm32lib/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_gpio.c
+
+SRC_S += \
+ hw/mcu/st/startup/stm32f4/startup_stm32f411xe.s
+
+INC += \
+ $(TOP)/hw/mcu/st/cmsis \
+ $(TOP)/hw/mcu/st/stm32lib/CMSIS/STM32F4xx/Include \
+ $(TOP)/hw/mcu/st/stm32lib/STM32F4xx_HAL_Driver/Inc \
+ $(TOP)/hw/bsp/stm32f411disco
+
+# For TinyUSB port source
+VENDOR = st
+CHIP_FAMILY = stm32f4
+
+# For freeRTOS port source
+FREERTOS_PORT = ARM_CM4F
+
+# For flash-jlink target
+JLINK_DEVICE = stm32f41ve
+JLINK_IF = swd
+
+# Path to STM32 Cube Programmer CLI, should be added into system path
+STM32Prog = STM32_Programmer_CLI
+
+# flash target using on-board stlink
+flash: $(BUILD)/$(BOARD)-firmware.elf
+ $(STM32Prog) --connect port=swd --write $< --go
diff --git a/hw/bsp/stm32f411disco/board_stm32f411disco.c b/hw/bsp/stm32f411disco/board_stm32f411disco.c
new file mode 100644
index 000000000..cb5983760
--- /dev/null
+++ b/hw/bsp/stm32f411disco/board_stm32f411disco.c
@@ -0,0 +1,188 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2019 Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#include "../board.h"
+
+#include "stm32f4xx.h"
+#include "stm32f4xx_hal_conf.h"
+
+#define LED_PORT GPIOD
+#define LED_PIN GPIO_PIN_13
+
+/**
+ * @brief System Clock Configuration
+ * The system Clock is configured as follow :
+ * System Clock source = PLL (HSE)
+ * SYSCLK(Hz) = 84000000
+ * HCLK(Hz) = 84000000
+ * AHB Prescaler = 1
+ * APB1 Prescaler = 2
+ * APB2 Prescaler = 1
+ * HSE Frequency(Hz) = 8000000
+ * PLL_M = 8
+ * PLL_N = 336
+ * PLL_P = 4
+ * PLL_Q = 7
+ * VDD(V) = 3.3
+ * Main regulator output voltage = Scale2 mode
+ * Flash Latency(WS) = 2
+ * @param None
+ * @retval None
+ */
+static void SystemClock_Config(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* Enable Power Control clock */
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ /* Enable HSE Oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 8;
+ RCC_OscInitStruct.PLL.PLLN = 336;
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4;
+ RCC_OscInitStruct.PLL.PLLQ = 7;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2
+ clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2);
+}
+
+void board_init(void)
+{
+#if CFG_TUSB_OS == OPT_OS_NONE
+ // 1ms tick timer
+ SysTick_Config(SystemCoreClock / 1000);
+#elif CFG_TUSB_OS == OPT_OS_FREERTOS
+ // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher )
+ //NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY );
+#endif
+
+ SystemClock_Config();
+
+ // Notify runtime of frequency change.
+ SystemCoreClockUpdate();
+
+ // Enable USB OTG clock
+ __HAL_RCC_USB_OTG_FS_CLK_ENABLE();
+
+
+ /* Configure USB FS GPIOs */
+ __HAL_RCC_GPIOA_CLK_ENABLE();
+
+ GPIO_InitTypeDef GPIO_InitStruct;
+
+ /* Configure DM DP Pins */
+ GPIO_InitStruct.Pin = GPIO_PIN_11 | GPIO_PIN_12;
+ GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* Configure VBUS Pin */
+ GPIO_InitStruct.Pin = GPIO_PIN_9;
+ GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* This for ID line debug */
+ GPIO_InitStruct.Pin = GPIO_PIN_10;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_OD;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ // Init the LED
+ __HAL_RCC_GPIOD_CLK_ENABLE();
+
+ GPIO_InitStruct.Pin = LED_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FAST;
+ HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
+
+ board_led_write(false);
+
+ // TODO Button
+}
+
+//--------------------------------------------------------------------+
+// Board porting API
+//--------------------------------------------------------------------+
+
+void board_led_write(bool state)
+{
+ HAL_GPIO_WritePin(LED_PORT, LED_PIN, state);
+}
+
+uint32_t board_button_read(void)
+{
+ // TODO implement
+ return 0;
+}
+
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+volatile uint32_t system_ticks = 0;
+void SysTick_Handler (void)
+{
+ system_ticks++;
+}
+
+uint32_t board_millis(void)
+{
+ return system_ticks;
+}
+#endif
+
+void HardFault_Handler (void)
+{
+ asm("bkpt");
+}
+
+// Required by __libc_init_array in startup code if we are compiling using
+// -nostdlib/-nostartfiles.
+void _init(void)
+{
+
+}
diff --git a/hw/bsp/stm32f411disco/stm32f4xx_hal_conf.h b/hw/bsp/stm32f411disco/stm32f4xx_hal_conf.h
new file mode 100644
index 000000000..d9a690041
--- /dev/null
+++ b/hw/bsp/stm32f411disco/stm32f4xx_hal_conf.h
@@ -0,0 +1,394 @@
+/**
+ ******************************************************************************
+ * @file GPIO/GPIO_EXTI/Inc/stm32f4xx_hal_conf.h
+ * @author MCD Application Team
+ * @brief HAL configuration file
+ ******************************************************************************
+ * @attention
+ *
+ * © COPYRIGHT(c) 2017 STMicroelectronics
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F4xx_HAL_CONF_H
+#define __STM32F4xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+ * @brief This is the list of modules to be used in the HAL driver
+ */
+#define HAL_MODULE_ENABLED
+/* #define HAL_ADC_MODULE_ENABLED */
+/* #define HAL_CAN_MODULE_ENABLED */
+/* #define HAL_CAN_LEGACY_MODULE_ENABLED */
+/* #define HAL_CRC_MODULE_ENABLED */
+/* #define HAL_CRYP_MODULE_ENABLED */
+/* #define HAL_DAC_MODULE_ENABLED */
+/* #define HAL_DCMI_MODULE_ENABLED */
+#define HAL_DMA_MODULE_ENABLED
+/* #define HAL_DMA2D_MODULE_ENABLED */
+/* #define HAL_ETH_MODULE_ENABLED */
+#define HAL_FLASH_MODULE_ENABLED
+/* #define HAL_NAND_MODULE_ENABLED */
+/* #define HAL_NOR_MODULE_ENABLED */
+/* #define HAL_PCCARD_MODULE_ENABLED */
+/* #define HAL_SRAM_MODULE_ENABLED */
+/* #define HAL_SDRAM_MODULE_ENABLED */
+/* #define HAL_HASH_MODULE_ENABLED */
+#define HAL_GPIO_MODULE_ENABLED
+// #define HAL_I2C_MODULE_ENABLED
+/* #define HAL_I2S_MODULE_ENABLED */
+/* #define HAL_IWDG_MODULE_ENABLED */
+/* #define HAL_LTDC_MODULE_ENABLED */
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+/* #define HAL_RNG_MODULE_ENABLED */
+/* #define HAL_RTC_MODULE_ENABLED */
+/* #define HAL_SAI_MODULE_ENABLED */
+/* #define HAL_SD_MODULE_ENABLED */
+// #define HAL_SPI_MODULE_ENABLED
+/* #define HAL_TIM_MODULE_ENABLED */
+/* #define HAL_UART_MODULE_ENABLED */
+/* #define HAL_USART_MODULE_ENABLED */
+/* #define HAL_IRDA_MODULE_ENABLED */
+/* #define HAL_SMARTCARD_MODULE_ENABLED */
+/* #define HAL_WWDG_MODULE_ENABLED */
+#define HAL_CORTEX_MODULE_ENABLED
+/* #define HAL_PCD_MODULE_ENABLED */
+/* #define HAL_HCD_MODULE_ENABLED */
+
+
+/* ########################## HSE/HSI Values adaptation ##################### */
+/**
+ * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSE is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE (8000000U) /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined (HSE_STARTUP_TIMEOUT)
+ #define HSE_STARTUP_TIMEOUT (100U) /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator (HSI) value.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSI is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE (16000000U) /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+ * @brief Internal Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSI_VALUE)
+ #define LSI_VALUE (32000U)
+#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+/**
+ * @brief External Low Speed oscillator (LSE) value.
+ */
+#if !defined (LSE_VALUE)
+ #define LSE_VALUE (32768U) /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+#if !defined (LSE_STARTUP_TIMEOUT)
+ #define LSE_STARTUP_TIMEOUT (5000U) /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief External clock source for I2S peripheral
+ * This value is used by the I2S HAL module to compute the I2S clock source
+ * frequency, this source is inserted directly through I2S_CKIN pad.
+ */
+#if !defined (EXTERNAL_CLOCK_VALUE)
+ #define EXTERNAL_CLOCK_VALUE (12288000U) /*!< Value of the External oscillator in Hz*/
+#endif /* EXTERNAL_CLOCK_VALUE */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+ === you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+ * @brief This is the HAL system configuration section
+ */
+#define VDD_VALUE (3300U) /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY (0x0FU) /*!< tick interrupt priority */
+#define USE_RTOS 0U
+#define PREFETCH_ENABLE 1U
+#define INSTRUCTION_CACHE_ENABLE 1U
+#define DATA_CACHE_ENABLE 1U
+
+#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */
+#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */
+#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */
+#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */
+#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */
+#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */
+#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */
+#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */
+#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */
+#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */
+#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */
+#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */
+#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */
+#define USE_HAL_FMPI2C_REGISTER_CALLBACKS 0U /* FMPI2C register callback disabled */
+#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */
+#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */
+#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */
+#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */
+#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */
+#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */
+#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */
+#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */
+#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */
+#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */
+#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */
+#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */
+#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */
+#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */
+#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */
+#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */
+#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */
+#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */
+#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */
+#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */
+#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */
+#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */
+#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */
+#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */
+
+/* ########################## Assert Selection ############################## */
+/**
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * HAL drivers code
+ */
+/* #define USE_FULL_ASSERT 1U */
+
+/* ################## SPI peripheral configuration ########################## */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+* Activated: CRC code is present inside driver
+* Deactivated: CRC code cleaned from driver
+*/
+
+#define USE_SPI_CRC 1U
+
+/* Includes ------------------------------------------------------------------*/
+/**
+ * @brief Include module's header file
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32f4xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32f4xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+ #include "stm32f4xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32f4xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32f4xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32f4xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
+ #include "stm32f4xx_hal_can_legacy.h"
+#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32f4xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+ #include "stm32f4xx_hal_cryp.h"
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DMA2D_MODULE_ENABLED
+ #include "stm32f4xx_hal_dma2d.h"
+#endif /* HAL_DMA2D_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32f4xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_DCMI_MODULE_ENABLED
+ #include "stm32f4xx_hal_dcmi.h"
+#endif /* HAL_DCMI_MODULE_ENABLED */
+
+#ifdef HAL_ETH_MODULE_ENABLED
+ #include "stm32f4xx_hal_eth.h"
+#endif /* HAL_ETH_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32f4xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+ #include "stm32f4xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+ #include "stm32f4xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+ #include "stm32f4xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_PCCARD_MODULE_ENABLED
+ #include "stm32f4xx_hal_pccard.h"
+#endif /* HAL_PCCARD_MODULE_ENABLED */
+
+#ifdef HAL_SDRAM_MODULE_ENABLED
+ #include "stm32f4xx_hal_sdram.h"
+#endif /* HAL_SDRAM_MODULE_ENABLED */
+
+#ifdef HAL_HASH_MODULE_ENABLED
+ #include "stm32f4xx_hal_hash.h"
+#endif /* HAL_HASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f4xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f4xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f4xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_LTDC_MODULE_ENABLED
+ #include "stm32f4xx_hal_ltdc.h"
+#endif /* HAL_LTDC_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f4xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+ #include "stm32f4xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f4xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SAI_MODULE_ENABLED
+ #include "stm32f4xx_hal_sai.h"
+#endif /* HAL_SAI_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+ #include "stm32f4xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f4xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f4xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f4xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f4xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f4xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f4xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f4xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f4xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+ #include "stm32f4xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr: If expr is false, it calls assert_failed function
+ * which reports the name of the source file and the source
+ * line number of the call that failed.
+ * If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(uint8_t* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F4xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/hw/mcu/st/README.md b/hw/mcu/st/README.md
index 203e47c38..c1313d8d7 100644
--- a/hw/mcu/st/README.md
+++ b/hw/mcu/st/README.md
@@ -47,6 +47,6 @@ these files in one place.
* ARM-provided headers are stored in the [cmsis](cmsis) directory.
* The linker script for the STM32F4-DISCOVERY board demo is supplied as
part of TinyUSB's
- [Board Support Packages](../../bsp/stm32f407g_disc1/STM32F407VGTx_FLASH.ld).
+ [Board Support Packages](../../bsp/stm32f407disco/STM32F407VGTx_FLASH.ld).
The above files were extracted from a dummy stm32cube project in February
2019.