diff --git a/hw/bsp/stm32f072eval/STM32F072VBTx_FLASH.ld b/hw/bsp/stm32f072eval/STM32F072VBTx_FLASH.ld
new file mode 100644
index 000000000..581613a5f
--- /dev/null
+++ b/hw/bsp/stm32f072eval/STM32F072VBTx_FLASH.ld
@@ -0,0 +1,177 @@
+/**
+ ******************************************************************************
+ * @file LinkerScript.ld
+ * @author Auto-generated by STM32CubeIDE
+ * Abstract : Linker script for STM32072B-EVAL Board embedding STM32F072VBTx Device from stm32f0 series
+ * 128Kbytes FLASH
+ * 16Kbytes RAM
+ *
+ * Set heap size, stack size and stack location according
+ * to application requirements.
+ *
+ * Set memory bank area and size if external memory is used
+ ******************************************************************************
+ * @attention
+ *
+ * © Copyright (c) 2020 STMicroelectronics.
+ * All rights reserved.
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200 ; /* required amount of heap */
+_Min_Stack_Size = 0x400 ; /* required amount of stack */
+
+/* Memories definition */
+MEMORY
+{
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 16K
+ FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 128K
+}
+
+/* Sections */
+SECTIONS
+{
+ /* The startup code into "FLASH" Rom type memory */
+ .isr_vector :
+ {
+ . = ALIGN(4);
+ KEEP(*(.isr_vector)) /* Startup code */
+ . = ALIGN(4);
+ } >FLASH
+
+ /* The program code and other data into "FLASH" Rom type memory */
+ .text :
+ {
+ . = ALIGN(4);
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ . = ALIGN(4);
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data into "FLASH" Rom type memory */
+ .rodata :
+ {
+ . = ALIGN(4);
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM.extab : {
+ . = ALIGN(4);
+ *(.ARM.extab* .gnu.linkonce.armextab.*)
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM : {
+ . = ALIGN(4);
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ . = ALIGN(4);
+ } >FLASH
+
+ .preinit_array :
+ {
+ . = ALIGN(4);
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ . = ALIGN(4);
+ } >FLASH
+
+ .init_array :
+ {
+ . = ALIGN(4);
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ . = ALIGN(4);
+ } >FLASH
+
+ .fini_array :
+ {
+ . = ALIGN(4);
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ . = ALIGN(4);
+ } >FLASH
+
+ /* Used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections into "RAM" Ram type memory */
+ .data :
+ {
+ . = ALIGN(4);
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+ *(.RamFunc) /* .RamFunc sections */
+ *(.RamFunc*) /* .RamFunc* sections */
+
+ . = ALIGN(4);
+ _edata = .; /* define a global symbol at data end */
+
+ } >RAM AT> FLASH
+
+ /* Uninitialized data section into "RAM" Ram type memory */
+ . = ALIGN(4);
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss section */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ . = ALIGN(4);
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+ /* Remove information from the compiler libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32f072eval/board.mk b/hw/bsp/stm32f072eval/board.mk
new file mode 100644
index 000000000..f5c66505f
--- /dev/null
+++ b/hw/bsp/stm32f072eval/board.mk
@@ -0,0 +1,50 @@
+ST_FAMILY = f0
+DEPS_SUBMODULES += lib/CMSIS_5 hw/mcu/st/cmsis_device_$(ST_FAMILY) hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
+
+ST_CMSIS = hw/mcu/st/cmsis_device_$(ST_FAMILY)
+ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
+
+CFLAGS += \
+ -flto \
+ -mthumb \
+ -mabi=aapcs \
+ -mcpu=cortex-m0 \
+ -mfloat-abi=soft \
+ -nostdlib -nostartfiles \
+ -DSTM32F072xB \
+ -DCFG_EXAMPLE_MSC_READONLY \
+ -DCFG_TUSB_MCU=OPT_MCU_STM32F0
+
+# suppress warning caused by vendor mcu driver
+CFLAGS += -Wno-error=unused-parameter -Wno-error=cast-align
+
+# All source paths should be relative to the top level.
+LD_FILE = hw/bsp/$(BOARD)/STM32F072VBTx_FLASH.ld
+
+SRC_C += \
+ src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c \
+ $(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \
+ $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \
+ $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \
+ $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \
+ $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \
+ $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c \
+ $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_uart.c
+
+SRC_S += \
+ $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f072xb.s
+
+INC += \
+ $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \
+ $(TOP)/$(ST_CMSIS)/Include \
+ $(TOP)/$(ST_HAL_DRIVER)/Inc \
+ $(TOP)/hw/bsp/$(BOARD)
+
+# For freeRTOS port source
+FREERTOS_PORT = ARM_CM0
+
+# For flash-jlink target
+JLINK_DEVICE = stm32f072vb
+
+# flash target using on-board stlink
+flash: flash-stlink
diff --git a/hw/bsp/stm32f072eval/stm32f072eval.c b/hw/bsp/stm32f072eval/stm32f072eval.c
new file mode 100644
index 000000000..e8486d88e
--- /dev/null
+++ b/hw/bsp/stm32f072eval/stm32f072eval.c
@@ -0,0 +1,245 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2019 Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#include "../board.h"
+#include "stm32f0xx_hal.h"
+
+//--------------------------------------------------------------------+
+// Forward USB interrupt events to TinyUSB IRQ Handler
+//--------------------------------------------------------------------+
+void USB_IRQHandler(void)
+{
+ tud_int_handler(0);
+}
+
+//--------------------------------------------------------------------+
+// MACRO TYPEDEF CONSTANT ENUM
+//--------------------------------------------------------------------+
+#define LED_PORT GPIOD
+#define LED_PIN GPIO_PIN_8 // LED1, GREEN
+// #define LED_PIN GPIO_PIN_9 // LED2, ORANGE
+// #define LED_PIN GPIO_PIN_10 // LED3, RED
+// #define LED_PIN GPIO_PIN_11 // LED4, BLUE
+#define LED_STATE_ON 0
+
+#define BUTTON_PORT GPIOA
+#define BUTTON_PIN GPIO_PIN_0 // JOY_SEL
+#define BUTTON_STATE_ACTIVE 1
+
+#define UARTx USART2
+#define UART_GPIO_PORT GPIOD
+#define UART_GPIO_AF GPIO_AF0_USART2
+#define UART_TX_PIN GPIO_PIN_5
+#define UART_RX_PIN GPIO_PIN_6
+
+UART_HandleTypeDef UartHandle;
+
+
+// enable all LED, Button, Uart, USB clock
+static void all_rcc_clk_enable(void)
+{
+ __HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D-, button
+ // __HAL_RCC_GPIOB_CLK_ENABLE();
+ //__HAL_RCC_GPIOC_CLK_ENABLE();
+ __HAL_RCC_GPIOD_CLK_ENABLE(); // Uart tx, rx, LED
+ __HAL_RCC_USART2_CLK_ENABLE(); // Uart module
+}
+
+/**
+ * @brief System Clock Configuration
+ * The system Clock is configured as follow :
+ * System Clock source = PLL (HSI48)
+ * SYSCLK(Hz) = 48000000
+ * HCLK(Hz) = 48000000
+ * AHB Prescaler = 1
+ * APB1 Prescaler = 1
+ * HSI Frequency(Hz) = 48000000
+ * PREDIV = 2
+ * PLLMUL = 2
+ * Flash Latency(WS) = 1
+ * @param None
+ * @retval None
+ */
+static void SystemClock_Config(void)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct = {0};
+ RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
+ RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};
+
+ /** Initializes the RCC Oscillators according to the specified parameters
+ * in the RCC_OscInitTypeDef structure.
+ */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSI48State = RCC_HSI48_ON;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL6;
+ RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV1;
+
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ /** Initializes the CPU, AHB and APB buses clocks
+ */
+ RCC_ClkInitStruct.ClockType =
+ RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
+
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1);
+
+ PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USB | RCC_PERIPHCLK_USART2;
+ PeriphClkInit.Usart2ClockSelection = RCC_USART2CLKSOURCE_PCLK1;
+ PeriphClkInit.UsbClockSelection = RCC_USBCLKSOURCE_HSI48;
+
+ HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
+}
+
+
+void board_init(void)
+{
+ SystemClock_Config();
+ all_rcc_clk_enable();
+
+ #if CFG_TUSB_OS == OPT_OS_NONE
+ // 1ms tick timer
+ SysTick_Config(SystemCoreClock / 1000);
+ #endif
+
+ // LED
+ GPIO_InitTypeDef GPIO_InitStruct;
+ GPIO_InitStruct.Pin = LED_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
+
+ // Button
+ GPIO_InitStruct.Pin = BUTTON_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+ GPIO_InitStruct.Pull = GPIO_PULLDOWN;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct);
+
+ // Uart
+ GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ GPIO_InitStruct.Alternate = UART_GPIO_AF;
+ HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct);
+
+ UartHandle.Instance = UARTx;
+ UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE;
+ UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
+ UartHandle.Init.StopBits = UART_STOPBITS_1;
+ UartHandle.Init.Parity = UART_PARITY_NONE;
+ UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
+ UartHandle.Init.Mode = UART_MODE_TX_RX;
+ UartHandle.Init.OverSampling = UART_OVERSAMPLING_16;
+ HAL_UART_Init(&UartHandle);
+
+ // USB Pins
+ // Configure USB DM and DP pins. This is optional, and maintained only for user guidance.
+ GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12);
+ GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ // USB Clock enable
+ __HAL_RCC_USB_CLK_ENABLE();
+}
+
+//--------------------------------------------------------------------+
+// Board porting API
+//--------------------------------------------------------------------+
+
+void board_led_write(bool state)
+{
+ HAL_GPIO_WritePin(LED_PORT, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON));
+}
+
+uint32_t board_button_read(void)
+{
+ return BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN);
+}
+
+int board_uart_read(uint8_t* buf, int len)
+{
+ (void) buf; (void) len;
+ return 0;
+}
+
+int board_uart_write(void const * buf, int len)
+{
+ HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff);
+ return len;
+}
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+volatile uint32_t system_ticks = 0;
+void SysTick_Handler (void)
+{
+ system_ticks++;
+}
+
+uint32_t board_millis(void)
+{
+ return system_ticks;
+}
+#endif
+
+void HardFault_Handler (void)
+{
+ asm("bkpt");
+}
+
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief Reports the name of the source file and the source line number
+ * where the assert_param error has occurred.
+ * @param file: pointer to the source file name
+ * @param line: assert_param error line source number
+ * @retval None
+ */
+void assert_failed(uint8_t* file, uint32_t line)
+{
+ (void) file; (void) line;
+ /* USER CODE BEGIN 6 */
+ /* User can add his own implementation to report the file name and line number,
+ tex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
+ /* USER CODE END 6 */
+}
+#endif /* USE_FULL_ASSERT */
+
+// Required by __libc_init_array in startup code if we are compiling using
+// -nostdlib/-nostartfiles.
+void _init(void)
+{
+
+}
diff --git a/hw/bsp/stm32f072eval/stm32f0xx_hal_conf.h b/hw/bsp/stm32f072eval/stm32f0xx_hal_conf.h
new file mode 100644
index 000000000..6fdf24f18
--- /dev/null
+++ b/hw/bsp/stm32f072eval/stm32f0xx_hal_conf.h
@@ -0,0 +1,321 @@
+/**
+ ******************************************************************************
+ * @file stm32f0xx_hal_conf.h
+ * @author MCD Application Team
+ * @brief HAL configuration file.
+ ******************************************************************************
+ * @attention
+ *
+ * © Copyright (c) 2016 STMicroelectronics.
+ * All rights reserved.
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_CONF_H
+#define __STM32F0xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+ * @brief This is the list of modules to be used in the HAL driver
+ */
+#define HAL_MODULE_ENABLED
+/*#define HAL_ADC_MODULE_ENABLED */
+/*#define HAL_CAN_MODULE_ENABLED */
+/*#define HAL_CEC_MODULE_ENABLED */
+/*#define HAL_COMP_MODULE_ENABLED */
+#define HAL_CORTEX_MODULE_ENABLED
+/*#define HAL_CRC_MODULE_ENABLED */
+/*#define HAL_DAC_MODULE_ENABLED */
+#define HAL_DMA_MODULE_ENABLED
+#define HAL_FLASH_MODULE_ENABLED
+#define HAL_GPIO_MODULE_ENABLED
+/*#define HAL_EXTI_MODULE_ENABLED */
+/*#define HAL_I2C_MODULE_ENABLED */
+/*#define HAL_I2S_MODULE_ENABLED */
+/*#define HAL_IRDA_MODULE_ENABLED */
+/*#define HAL_IWDG_MODULE_ENABLED */
+#define HAL_PCD_MODULE_ENABLED
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+/*#define HAL_RTC_MODULE_ENABLED */
+/*#define HAL_SMARTCARD_MODULE_ENABLED */
+/*#define HAL_SMBUS_MODULE_ENABLED */
+/*#define HAL_SPI_MODULE_ENABLED */
+/*#define HAL_TIM_MODULE_ENABLED */
+/*#define HAL_TSC_MODULE_ENABLED */
+#define HAL_UART_MODULE_ENABLED
+/*#define HAL_USART_MODULE_ENABLED */
+/*#define HAL_WWDG_MODULE_ENABLED */
+
+/* ######################### Oscillator Values adaptation ################### */
+/**
+ * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSE is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+/**
+ * @brief In the following line adjust the External High Speed oscillator (HSE) Startup
+ * Timeout value
+ */
+#if !defined (HSE_STARTUP_TIMEOUT)
+ #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator (HSI) value.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSI is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE 8000000U /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+ * @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup
+ * Timeout value
+ */
+#if !defined (HSI_STARTUP_TIMEOUT)
+ #define HSI_STARTUP_TIMEOUT 5000U /*!< Time out for HSI start up */
+#endif /* HSI_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator for ADC (HSI14) value.
+ */
+#if !defined (HSI14_VALUE)
+ #define HSI14_VALUE 14000000U /*!< Value of the Internal High Speed oscillator for ADC in Hz.
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+#endif /* HSI14_VALUE */
+
+/**
+ * @brief Internal High Speed oscillator for USB (HSI48) value.
+ */
+#if !defined (HSI48_VALUE)
+ #define HSI48_VALUE 48000000U /*!< Value of the Internal High Speed oscillator for USB in Hz.
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+#endif /* HSI48_VALUE */
+
+/**
+ * @brief Internal Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSI_VALUE)
+ #define LSI_VALUE 40000U
+#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+/**
+ * @brief External Low Speed oscillator (LSE) value.
+ */
+#if !defined (LSE_VALUE)
+ #define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+/**
+ * @brief Time out for LSE start up value in ms.
+ */
+#if !defined (LSE_STARTUP_TIMEOUT)
+ #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+ === you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+ * @brief This is the HAL system configuration section
+ */
+#define VDD_VALUE 3300U /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY ((uint32_t)(1U<<__NVIC_PRIO_BITS) - 1U) /*!< tick interrupt priority (lowest by default) */
+ /* Warning: Must be set to higher priority for HAL_Delay() */
+ /* and HAL_GetTick() usage under interrupt context */
+#define USE_RTOS 0U
+#define PREFETCH_ENABLE 1U
+#define INSTRUCTION_CACHE_ENABLE 0U
+#define DATA_CACHE_ENABLE 0U
+#define USE_SPI_CRC 1U
+
+#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */
+#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */
+#define USE_HAL_COMP_REGISTER_CALLBACKS 0U /* COMP register callback disabled */
+#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */
+#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */
+#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */
+#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */
+#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */
+#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */
+#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */
+#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */
+#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */
+#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */
+#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */
+#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */
+#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */
+#define USE_HAL_TSC_REGISTER_CALLBACKS 0U /* TSC register callback disabled */
+#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */
+
+/* ########################## Assert Selection ############################## */
+/**
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * HAL drivers code
+ */
+ #define USE_FULL_ASSERT 1
+
+/* Includes ------------------------------------------------------------------*/
+/**
+ * @brief Include module's header file
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32f0xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32f0xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_EXTI_MODULE_ENABLED
+ #include "stm32f0xx_hal_exti.h"
+#endif /* HAL_EXTI_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+ #include "stm32f0xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32f0xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32f0xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32f0xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CEC_MODULE_ENABLED
+ #include "stm32f0xx_hal_cec.h"
+#endif /* HAL_CEC_MODULE_ENABLED */
+
+#ifdef HAL_COMP_MODULE_ENABLED
+ #include "stm32f0xx_hal_comp.h"
+#endif /* HAL_COMP_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32f0xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32f0xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32f0xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f0xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f0xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f0xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f0xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f0xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f0xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f0xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f0xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_SMBUS_MODULE_ENABLED
+ #include "stm32f0xx_hal_smbus.h"
+#endif /* HAL_SMBUS_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f0xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f0xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_TSC_MODULE_ENABLED
+ #include "stm32f0xx_hal_tsc.h"
+#endif /* HAL_TSC_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f0xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f0xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f0xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr If expr is false, it calls assert_failed function
+ * which reports the name of the source file and the source
+ * line number of the call that failed.
+ * If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(uint8_t* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F0xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+