diff --git a/docs/boards.md b/docs/boards.md index 7a33bab8d..202602d30 100644 --- a/docs/boards.md +++ b/docs/boards.md @@ -90,6 +90,7 @@ This code base already had supported for a handful of following boards (sorted a - STM32 F411ce Black Pill - [STM32 F411ve Discovery](https://www.st.com/en/evaluation-tools/32f411ediscovery.html) - [STM32 F412zg Discovery](https://www.st.com/en/evaluation-tools/32f412gdiscovery.html) +- [STM32 F746zg Nucleo](https://www.st.com/en/evaluation-tools/nucleo-f746zg.html) - [STM32 F767zi Nucleo](https://www.st.com/en/evaluation-tools/nucleo-f767zi.html) - [STM32 H743zi Nucleo](https://www.st.com/en/evaluation-tools/nucleo-h743zi.html) diff --git a/hw/bsp/stm32f746nucleo/STM32F746ZGTx_FLASH.ld b/hw/bsp/stm32f746nucleo/STM32F746ZGTx_FLASH.ld new file mode 100644 index 000000000..b434a01b7 --- /dev/null +++ b/hw/bsp/stm32f746nucleo/STM32F746ZGTx_FLASH.ld @@ -0,0 +1,167 @@ +/* +***************************************************************************** +** + +** File : LinkerScript.ld +** +** Abstract : Linker script for STM32F746ZGTx Device with +** 1024KByte FLASH, 320KByte RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +** (c)Copyright Ac6. +** You may use this file as-is or modify it according to the needs of your +** project. Distribution of this file (unmodified or modified) is not +** permitted. Ac6 permit registered System Workbench for MCU users the +** rights to distribute the assembled, compiled & linked contents of this +** file as part of an application binary file, provided that it is built +** using the System Workbench for MCU toolchain. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20050000; /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x460; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 320K +FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 1024K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} diff --git a/hw/bsp/stm32f746nucleo/board.mk b/hw/bsp/stm32f746nucleo/board.mk new file mode 100644 index 000000000..7e070c1c5 --- /dev/null +++ b/hw/bsp/stm32f746nucleo/board.mk @@ -0,0 +1,48 @@ +CFLAGS += \ + -flto \ + -mthumb \ + -mabi=aapcs \ + -mcpu=cortex-m7 \ + -mfloat-abi=hard \ + -mfpu=fpv5-d16 \ + -nostdlib -nostartfiles \ + -DSTM32F746xx \ + -DCFG_TUSB_MCU=OPT_MCU_STM32F7 + +# mcu driver cause following warnings +CFLAGS += -Wno-error=shadow + +ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F7xx_HAL_Driver +ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F7xx + +# All source paths should be relative to the top level. +LD_FILE = hw/bsp/$(BOARD)/STM32F746ZGTx_FLASH.ld + +SRC_C += \ + $(ST_CMSIS)/Source/Templates/system_stm32f7xx.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_cortex.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_rcc.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_rcc_ex.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_gpio.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_uart.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_pwr_ex.c + +SRC_S += \ + $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f746xx.s + +INC += \ + $(TOP)/hw/mcu/st/st_driver/CMSIS/Include \ + $(TOP)/$(ST_CMSIS)/Include \ + $(TOP)/$(ST_HAL_DRIVER)/Inc \ + $(TOP)/hw/bsp/$(BOARD) + +# For TinyUSB port source +VENDOR = st +CHIP_FAMILY = synopsys + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM7/r0p1 + +# flash target using on-board stlink +flash: flash-stlink diff --git a/hw/bsp/stm32f746nucleo/stm32f746nucleo.c b/hw/bsp/stm32f746nucleo/stm32f746nucleo.c new file mode 100644 index 000000000..8e0cb78e3 --- /dev/null +++ b/hw/bsp/stm32f746nucleo/stm32f746nucleo.c @@ -0,0 +1,255 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019 William D. Jones (thor0505@comcast.net), + * Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "../board.h" + +#include "stm32f7xx_hal.h" + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void OTG_FS_IRQHandler(void) +{ + tud_int_handler(0); +} + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ + +#define LED_PORT GPIOB +#define LED_PIN GPIO_PIN_14 +#define LED_STATE_ON 1 + +#define BUTTON_PORT GPIOC +#define BUTTON_PIN GPIO_PIN_13 +#define BUTTON_STATE_ACTIVE 1 + +#define UARTx USART3 +#define UART_GPIO_PORT GPIOD +#define UART_GPIO_AF GPIO_AF7_USART3 +#define UART_TX_PIN GPIO_PIN_8 +#define UART_RX_PIN GPIO_PIN_9 + +UART_HandleTypeDef UartHandle; + +// enable all LED, Button, Uart, USB clock +static void all_rcc_clk_enable(void) +{ + __HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D- + __HAL_RCC_GPIOB_CLK_ENABLE(); // LED + __HAL_RCC_GPIOC_CLK_ENABLE(); // Button + __HAL_RCC_GPIOD_CLK_ENABLE(); // Uart tx, rx + __HAL_RCC_USART3_CLK_ENABLE(); // Uart module +} + +/** + * @brief System Clock Configuration + * The system Clock is configured as follow : + * System Clock source = PLL (HSE) + * SYSCLK(Hz) = 216000000 + * HCLK(Hz) = 216000000 + * AHB Prescaler = 1 + * APB1 Prescaler = 4 + * APB2 Prescaler = 2 + * HSE Frequency(Hz) = 8000000 + * PLL_M = HSE_VALUE/1000000 + * PLL_N = 432 + * PLL_P = 2 + * PLL_Q = 9 + * VDD(V) = 3.3 + * Main regulator output voltage = Scale1 mode + * Flash Latency(WS) = 7 + * The USB clock configuration from PLLSAI: + * PLLSAIP = 8 + * PLLSAIN = 384 + * PLLSAIQ = 7 + * @param None + * @retval None + */ +void SystemClock_Config(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + + /* Enable Power Control clock */ + __HAL_RCC_PWR_CLK_ENABLE(); + + /* The voltage scaling allows optimizing the power consumption when the device is + clocked below the maximum system frequency, to update the voltage scaling value + regarding system frequency refer to product datasheet. */ + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); + + /* Enable HSE Oscillator and activate PLL with HSE as source */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000; + RCC_OscInitStruct.PLL.PLLN = 432; + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; + RCC_OscInitStruct.PLL.PLLQ = 9; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + /* Activate the OverDrive to reach the 216 MHz Frequency */ + HAL_PWREx_EnableOverDrive(); + + /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; + + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7); +} + +void board_init(void) +{ + + + SystemClock_Config(); + all_rcc_clk_enable(); + +#if CFG_TUSB_OS == OPT_OS_NONE + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); +#endif + + GPIO_InitTypeDef GPIO_InitStruct; + + // LED + GPIO_InitStruct.Pin = LED_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); + + // Button + GPIO_InitStruct.Pin = BUTTON_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); + + // Uart + GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Alternate = UART_GPIO_AF; + HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct); + + UartHandle.Instance = UARTx; + UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; + UartHandle.Init.WordLength = UART_WORDLENGTH_8B; + UartHandle.Init.StopBits = UART_STOPBITS_1; + UartHandle.Init.Parity = UART_PARITY_NONE; + UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE; + UartHandle.Init.Mode = UART_MODE_TX_RX; + UartHandle.Init.OverSampling = UART_OVERSAMPLING_16; + HAL_UART_Init(&UartHandle); + + /* Configure USB FS GPIOs */ + /* Configure DM DP Pins */ + GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12); + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Configure VBUS Pin */ + GPIO_InitStruct.Pin = GPIO_PIN_9; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Configure ID pin */ + GPIO_InitStruct.Pin = GPIO_PIN_10; + GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Enable USB FS Clocks */ + __HAL_RCC_USB_OTG_FS_CLK_ENABLE(); + + // Enable VBUS sense (B device) via pin PA9 + USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN; +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + HAL_GPIO_WritePin(LED_PORT, LED_PIN, state); +} + +uint32_t board_button_read(void) +{ + return HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN); +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ + HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff); + return len; +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler (void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif + +void HardFault_Handler (void) +{ + asm("bkpt"); +} + +// Required by __libc_init_array in startup code if we are compiling using +// -nostdlib/-nostartfiles. +void _init(void) +{ + +} diff --git a/hw/bsp/stm32f746nucleo/stm32f7xx_hal_conf.h b/hw/bsp/stm32f746nucleo/stm32f7xx_hal_conf.h new file mode 100644 index 000000000..234191b00 --- /dev/null +++ b/hw/bsp/stm32f746nucleo/stm32f7xx_hal_conf.h @@ -0,0 +1,472 @@ +/** + ****************************************************************************** + * @file stm32f7xx_hal_conf.h + * @author MCD Application Team + * @brief HAL configuration file. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F7xx_HAL_CONF_H +#define __STM32F7xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +/* #define HAL_ADC_MODULE_ENABLED */ +/* #define HAL_CAN_MODULE_ENABLED */ +/* #define HAL_CAN_LEGACY_MODULE_ENABLED */ +/* #define HAL_CEC_MODULE_ENABLED */ +/* #define HAL_CRC_MODULE_ENABLED */ +/* #define HAL_CRYP_MODULE_ENABLED */ +/* #define HAL_DAC_MODULE_ENABLED */ +/* #define HAL_DCMI_MODULE_ENABLED */ +#define HAL_DMA_MODULE_ENABLED +/* #define HAL_DMA2D_MODULE_ENABLED */ +/* #define HAL_ETH_MODULE_ENABLED */ +#define HAL_FLASH_MODULE_ENABLED +/* #define HAL_NAND_MODULE_ENABLED */ +/* #define HAL_NOR_MODULE_ENABLED */ +/* #define HAL_SRAM_MODULE_ENABLED */ +/* #define HAL_SDRAM_MODULE_ENABLED */ +/* #define HAL_HASH_MODULE_ENABLED */ +#define HAL_GPIO_MODULE_ENABLED +/* #define HAL_I2C_MODULE_ENABLED */ +/* #define HAL_I2S_MODULE_ENABLED */ +/* #define HAL_IWDG_MODULE_ENABLED */ +/* #define HAL_LPTIM_MODULE_ENABLED */ +/* #define HAL_LTDC_MODULE_ENABLED */ +#define HAL_PWR_MODULE_ENABLED +/* #define HAL_QSPI_MODULE_ENABLED */ +#define HAL_RCC_MODULE_ENABLED +/* #define HAL_RNG_MODULE_ENABLED */ +/* #define HAL_RTC_MODULE_ENABLED */ +/* #define HAL_SAI_MODULE_ENABLED */ +/* #define HAL_SD_MODULE_ENABLED */ +/* #define HAL_SPDIFRX_MODULE_ENABLED */ +/* #define HAL_SPI_MODULE_ENABLED */ +/* #define HAL_TIM_MODULE_ENABLED */ +#define HAL_UART_MODULE_ENABLED +/* #define HAL_USART_MODULE_ENABLED */ +/* #define HAL_IRDA_MODULE_ENABLED */ +/* #define HAL_SMARTCARD_MODULE_ENABLED */ +/* #define HAL_WWDG_MODULE_ENABLED */ +#define HAL_CORTEX_MODULE_ENABLED +/* #define HAL_PCD_MODULE_ENABLED */ +/* #define HAL_HCD_MODULE_ENABLED */ +/* #define HAL_DFSDM_MODULE_ENABLED */ +/* #define HAL_DSI_MODULE_ENABLED */ +/* #define HAL_JPEG_MODULE_ENABLED */ +/* #define HAL_MDIOS_MODULE_ENABLED */ + + +/* ########################## HSE/HSI Values adaptation ##################### */ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) + #define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) + #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#if !defined (LSI_VALUE) + #define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature. */ +/** + * @brief External Low Speed oscillator (LSE) value. + */ +#if !defined (LSE_VALUE) + #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */ +#endif /* LSE_VALUE */ + +#if !defined (LSE_STARTUP_TIMEOUT) + #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +/** + * @brief External clock source for I2S peripheral + * This value is used by the I2S HAL module to compute the I2S clock source + * frequency, this source is inserted directly through I2S_CKIN pad. + */ +#if !defined (EXTERNAL_CLOCK_VALUE) + #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the Internal oscillator in Hz*/ +#endif /* EXTERNAL_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY ((uint32_t)0x0FU) /*!< tick interrupt priority */ +#define USE_RTOS 0U +#define PREFETCH_ENABLE 1U +#define ART_ACCLERATOR_ENABLE 1U /* To enable instruction cache and prefetch */ + +#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ +#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ +#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ +#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ +#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ +#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ +#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */ +#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */ +#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */ +#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ +#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ +#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ +#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ +#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ +#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ +#define USE_HAL_JPEG_REGISTER_CALLBACKS 0U /* JPEG register callback disabled */ +#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */ +#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */ +#define USE_HAL_MDIOS_REGISTER_CALLBACKS 0U /* MDIOS register callback disabled */ +#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ +#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ +#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ +#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ +#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */ +#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ +#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ +#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */ +#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ +#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ +#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */ +#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ +#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */ +#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ +#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ +#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ +#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1 */ + +/* ################## Ethernet peripheral configuration for NUCLEO 144 board ##################### */ + +/* Section 1 : Ethernet peripheral configuration */ + +/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ +#define MAC_ADDR0 2U +#define MAC_ADDR1 0U +#define MAC_ADDR2 0U +#define MAC_ADDR3 0U +#define MAC_ADDR4 0U +#define MAC_ADDR5 0U + +/* Definition of the Ethernet driver buffers size and count */ +#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ +#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ +#define ETH_RXBUFNB ((uint32_t)5) /* 5 Rx buffers of size ETH_RX_BUF_SIZE */ +#define ETH_TXBUFNB ((uint32_t)5) /* 5 Tx buffers of size ETH_TX_BUF_SIZE */ + +/* Section 2: PHY configuration section */ +/* LAN8742A PHY Address*/ +#define LAN8742A_PHY_ADDRESS 0x00 +/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ +#define PHY_RESET_DELAY ((uint32_t)0x00000FFF) +/* PHY Configuration delay */ +#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF) + +#define PHY_READ_TO ((uint32_t)0x0000FFFF) +#define PHY_WRITE_TO ((uint32_t)0x0000FFFF) + +/* Section 3: Common PHY Registers */ + +#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */ +#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */ + +#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ +#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ +#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ +#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ +#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ +#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ +#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ +#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ +#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ +#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ + +#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ +#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ +#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ + +/* Section 4: Extended PHY Registers */ + +#define PHY_SR ((uint16_t)0x1F) /*!< PHY special control/ status register Offset */ + +#define PHY_SPEED_STATUS ((uint16_t)0x0004) /*!< PHY Speed mask */ +#define PHY_DUPLEX_STATUS ((uint16_t)0x0010) /*!< PHY Duplex mask */ + + +#define PHY_ISFR ((uint16_t)0x1D) /*!< PHY Interrupt Source Flag register Offset */ +#define PHY_ISFR_INT4 ((uint16_t)0x0010) /*!< PHY Link down inturrupt */ + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver +* Activated: CRC code is present inside driver +* Deactivated: CRC code cleaned from driver +*/ + +#define USE_SPI_CRC 1U + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32f7xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32f7xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32f7xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32f7xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32f7xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED + #include "stm32f7xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_CAN_LEGACY_MODULE_ENABLED + #include "stm32f7xx_hal_can_legacy.h" +#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED + #include "stm32f7xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32f7xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED + #include "stm32f7xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DMA2D_MODULE_ENABLED + #include "stm32f7xx_hal_dma2d.h" +#endif /* HAL_DMA2D_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32f7xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_DCMI_MODULE_ENABLED + #include "stm32f7xx_hal_dcmi.h" +#endif /* HAL_DCMI_MODULE_ENABLED */ + +#ifdef HAL_ETH_MODULE_ENABLED + #include "stm32f7xx_hal_eth.h" +#endif /* HAL_ETH_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32f7xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED + #include "stm32f7xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED + #include "stm32f7xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED + #include "stm32f7xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_SDRAM_MODULE_ENABLED + #include "stm32f7xx_hal_sdram.h" +#endif /* HAL_SDRAM_MODULE_ENABLED */ + +#ifdef HAL_HASH_MODULE_ENABLED + #include "stm32f7xx_hal_hash.h" +#endif /* HAL_HASH_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32f7xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED + #include "stm32f7xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32f7xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED + #include "stm32f7xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_LTDC_MODULE_ENABLED + #include "stm32f7xx_hal_ltdc.h" +#endif /* HAL_LTDC_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32f7xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_QSPI_MODULE_ENABLED + #include "stm32f7xx_hal_qspi.h" +#endif /* HAL_QSPI_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED + #include "stm32f7xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32f7xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SAI_MODULE_ENABLED + #include "stm32f7xx_hal_sai.h" +#endif /* HAL_SAI_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED + #include "stm32f7xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SPDIFRX_MODULE_ENABLED + #include "stm32f7xx_hal_spdifrx.h" +#endif /* HAL_SPDIFRX_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32f7xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32f7xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32f7xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32f7xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32f7xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32f7xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32f7xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32f7xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED + #include "stm32f7xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +#ifdef HAL_DFSDM_MODULE_ENABLED + #include "stm32f7xx_hal_dfsdm.h" +#endif /* HAL_DFSDM_MODULE_ENABLED */ + +#ifdef HAL_DSI_MODULE_ENABLED + #include "stm32f7xx_hal_dsi.h" +#endif /* HAL_DSI_MODULE_ENABLED */ + +#ifdef HAL_JPEG_MODULE_ENABLED + #include "stm32f7xx_hal_jpeg.h" +#endif /* HAL_JPEG_MODULE_ENABLED */ + +#ifdef HAL_MDIOS_MODULE_ENABLED + #include "stm32f7xx_hal_mdios.h" +#endif /* HAL_MDIOS_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t* file, uint32_t line); +#else + #define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F7xx_HAL_CONF_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/